Pas de connexion wifi avec nouvelle box

@Verner
Merci pour la précaution mais je n’ai aucune intention de tout casser, je cherche à droite et à gauche et je pose des questions

joel@joel-k70ij:~$ lsmod | grep '^ath'
ath9k                 143360  0
ath9k_common           20480  1 ath9k
ath9k_hw              503808  2 ath9k_common,ath9k
ath                    36864  3 ath9k_common,ath9k,ath9k_hw
joel@joel-k70ij:~$ ls /lib/firmware/ath9k*
ls: impossible d'accéder à '/lib/firmware/ath9k*': Aucun fichier ou dossier de ce type
joel@joel-k70ij:~$ ls /sys/class/net/
enp3s0  lo  wlp2s0
joel@joel-k70ij:~$ sudo apt install wireless-tools
[sudo] Mot de passe de joel : 
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances... Fait
Lecture des informations d'état... Fait      
wireless-tools est déjà la version la plus récente (30~pre9-13.1).
wireless-tools passé en « installé manuellement ».
0 mis à jour, 0 nouvellement installés, 0 à enlever et 0 non mis à jour.
joel@joel-k70ij:~$ /sbin/iwlist wlan0 channel
wlan0     no frequency information.
joel@joel-k70ij:~$ /sbin/iwlist wlan0 scanning |grep ESSID
wlan0     Interface doesn't support scanning.

Voilà, c’est exactement ça, il te manque les firmwares atheros.

Sinon, que donne la commande suivante ?

sudo iw dev wlp2s0 scan

Tu confirmes que ton wifi fonctionnait parfaitement avec la box précédente sans les firmware atheros ???
Si oui, ton wifi n’utilise pas atheros, mais autre chose: pas très clair tout ça.

Ta connexion s’appelle wlp2s0 et non pas wlan0.
rappel: ‹ # en supposant que wlan0 soit le nom de ta connexion wifi: ›
Donc, refais:

/sbin/iwlist wlp2s0 channel
/sbin/iwlist wlp2s0 scanning |grep ESSID

Pour clarifier: tu utilises ubuntu ou Debian ?

Et
/sbin/iwlist wlp2s0 auth

@Almtesh

joel@joel-k70ij:~$ sudo iw dev wlp2s0 scan
[sudo] Mot de passe de joel : 
BSS 50:39:2f:4a:9c:90(on wlp2s0)
	TSF: 15631038770 usec (0d, 04:20:31)
	freq: 2412
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
	signal: -35.00 dBm
	last seen: 944 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-9C90
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 1
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	Power constraint: 0 dB
	TPC report: TX power: 17 dBm
	ERP: <no flags>
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 0
		 * channel utilisation: 35/255
		 * available admission capacity: 0 [*32us]
	Measurement Pilot Transmission:
		 * interval: 0 TUs
	RM enabled capabilities:
		Capabilities: 0x33 0x4f 0x01 0x00 0x00
			Link Measurement
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
			Frame Measurement
			Channel Load
			Noise Histogram Measurement
			Statistics Measurement
			Transmit Stream/Category Measurement
			AP Channel Report
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0x9ac
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 1
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: nonmember
		 * non-GF present: 0
		 * OBSS non-GF present: 1
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * BSS Transition
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 00000000-0000-0000-0000-000000000000
		 * Manufacturer: Sagemcom
		 * Model: SagemcomFast5656_OFR
		 * Model Number: SG_LBF_1.2.1
		 * Serial Number: IA22172FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox Fibre
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x1
		 * Version2: 2.0
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 44:a6:1e:a1:6a:86(on wlp2s0)
	TSF: 190528875449 usec (2d, 04:55:28)
	freq: 2437
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
	signal: -66.00 dBm
	last seen: 648 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-6A86
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 6
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	Power constraint: 0 dB
	TPC report: TX power: 16 dBm
	ERP: <no flags>
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 0
		 * channel utilisation: 39/255
		 * available admission capacity: 0 [*32us]
	RM enabled capabilities:
		Capabilities: 0x32 0x00 0x00 0x00 0x00
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0x1ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-23
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 6
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 34344136-3145-f131-f641-383634344136
		 * Manufacturer: Sagemcom
		 * Model: SagemcomFast5360_MIB4
		 * Model Number: SG_LB4_1.2.0
		 * Serial Number: AN20055FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox 4
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x1
		 * Version2: 2.0
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 70:fc:8f:3d:7e:b4(on wlp2s0)
	TSF: 585260144991 usec (6d, 18:34:20)
	freq: 2437
	beacon interval: 120 TUs
	capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
	signal: -89.00 dBm
	last seen: 692 ms ago
	SSID: Freebox_2629
	Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0 
	DS Parameter set: channel 6
	TIM: DTIM Count 0 DTIM Period 2 Bitmap Control 0x0 Bitmap[0] 0x4
	ERP: Barker_Preamble_Mode
	Extended supported rates: 24.0 36.0 48.0 54.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 4
		 * channel utilisation: 51/255
		 * available admission capacity: 0 [*32us]
	RM enabled capabilities:
		Capabilities: 0x72 0x00 0x00 0x00 0x00
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
			Beacon Table Measurement
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0xee
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			No RX STBC
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: No restriction (0x00)
		HT TX/RX MCS rate indexes supported: 0-23, 32
	HT operation:
		 * primary channel: 6
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * BSS Transition
		 * SSID List
		 * Operating Mode Notification
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 50:39:2f:3e:9f:20(on wlp2s0)
	TSF: 317129640241 usec (3d, 16:05:29)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy SpectrumMgmt ShortSlotTime RadioMeasure (0x1511)
	signal: -87.00 dBm
	last seen: 208 ms ago
	Information elements from Probe Response frame:
	SSID: Livebox-9F20
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 11
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 20 dBm
	Power constraint: 0 dB
	TPC report: TX power: 17 dBm
	ERP: Barker_Preamble_Mode
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 1
		 * channel utilisation: 36/255
		 * available admission capacity: 0 [*32us]
	Measurement Pilot Transmission:
		 * interval: 0 TUs
	RM enabled capabilities:
		Capabilities: 0x33 0x4f 0x01 0x00 0x00
			Link Measurement
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
			Frame Measurement
			Channel Load
			Noise Histogram Measurement
			Statistics Measurement
			Transmit Stream/Category Measurement
			AP Channel Report
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0x9ac
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * BSS Transition
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 00000000-0000-0000-0000-000000000000
		 * Manufacturer: Sagemcom
		 * Model: SagemcomFast5656_OFR
		 * Model Number: SG_LBF_1.2.1
		 * Serial Number: IA22131FF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: Livebox Fibre
		 * Config methods: Ethernet, Label
		 * RF Bands: 0x1
		 * Version2: 2.0
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 34:49:5b:df:22:60(on wlp2s0)
	TSF: 2291076836730 usec (26d, 12:24:36)
	freq: 2412
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -89.00 dBm
	last seen: 1004 ms ago
	Information elements from Probe Response frame:
	SSID: Bbox-C1EDD1A7
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 1
	ERP: <no flags>
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 0
		 * channel utilisation: 31/255
		 * available admission capacity: 0 [*32us]
	Measurement Pilot Transmission:
		 * interval: 0 TUs
	HT capabilities:
		Capabilities: 0x8bc
			HT20
			SM Power Save disabled
			RX Greenfield
			RX HT20 SGI
			TX STBC
			No RX STBC
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 1
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * BSS Transition
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: 111242c3-4f87-50b9-4fcb-c503bbf806af
		 * Manufacturer: Broadcom
		 * Model: Broadcom
		 * Model Number: 123456
		 * Serial Number: 1234
		 * Primary Device Type: 6-0050f204-1
		 * Device name: BroadcomAP
		 * Config methods: Label, Display
		 * RF Bands: 0x1
		 * Version2: 2.0
	WPA:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 76:79:70:76:8c:84(on wlp2s0)
	TSF: 2291163955570 usec (26d, 12:26:03)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -88.00 dBm
	last seen: 392 ms ago
	SSID: papaquenamel
	Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0 
	DS Parameter set: channel 11
	Extended supported rates: 6.0 12.0 24.0 48.0 
	AP Channel Report:
		 * operating class: 32
		 * channel(s): 1 2 3 4 5 6 7
	AP Channel Report:
		 * operating class: 33
		 * channel(s): 5 6 7 8 9 10 11
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0xc
	ERP: Barker_Preamble_Mode
	HT capabilities:
		Capabilities: 0x106e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * HT Information Exchange Supported
	WPA:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: TKIP CCMP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	BSS Load:
		 * station count: 1
		 * channel utilisation: 74/255
		 * available admission capacity: 31250 [*32us]
BSS 76:79:70:76:8c:85(on wlp2s0)
	TSF: 2291163958075 usec (26d, 12:26:03)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -90.00 dBm
	last seen: 392 ms ago
	SSID: 
	Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0 
	DS Parameter set: channel 11
	Extended supported rates: 6.0 12.0 24.0 48.0 
	AP Channel Report:
		 * operating class: 32
		 * channel(s): 1 2 3 4 5 6 7
	AP Channel Report:
		 * operating class: 33
		 * channel(s): 5 6 7 8 9 10 11
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	HT capabilities:
		Capabilities: 0x106e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * HT Information Exchange Supported
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	BSS Load:
		 * station count: 1
		 * channel utilisation: 74/255
		 * available admission capacity: 31250 [*32us]
BSS 76:79:70:76:8c:86(on wlp2s0)
	TSF: 2291163960437 usec (26d, 12:26:03)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -86.00 dBm
	last seen: 388 ms ago
	SSID: FreeWifi_secure
	Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0 
	DS Parameter set: channel 11
	Extended supported rates: 6.0 12.0 24.0 48.0 
	AP Channel Report:
		 * operating class: 32
		 * channel(s): 1 2 3 4 5 6 7
	AP Channel Report:
		 * operating class: 33
		 * channel(s): 5 6 7 8 9 10 11
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	HT capabilities:
		Capabilities: 0x106e
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: 20 MHz
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * HT Information Exchange Supported
	WPA:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: IEEE 802.1X
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	BSS Load:
		 * station count: 1
		 * channel utilisation: 74/255
		 * available admission capacity: 31250 [*32us]
BSS cc:2d:1b:b1:43:fe(on wlp2s0)
	TSF: 30381158814 usec (0d, 08:26:21)
	freq: 2412
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
	signal: -91.00 dBm
	last seen: 1044 ms ago
	SSID: HG BG 10 2021 2G
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 1
	TIM: DTIM Count 0 DTIM Period 3 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 1
		 * channel utilisation: 53/255
		 * available admission capacity: 0 [*32us]
	RM enabled capabilities:
		Capabilities: 0x32 0x08 0x01 0x00 0x00
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
			Statistics Measurement
			AP Channel Report
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0x8bc
			HT20
			SM Power Save disabled
			RX Greenfield
			RX HT20 SGI
			TX STBC
			No RX STBC
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 1
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * BSS Transition
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
	WPA:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 6c:ba:b8:0a:d9:90(on wlp2s0)
	TSF: 2291071590801 usec (26d, 12:24:31)
	freq: 2412
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime (0x0411)
	signal: -84.00 dBm
	last seen: 1028 ms ago
	SSID: \x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 1
	TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 1
		 * channel utilisation: 34/255
		 * available admission capacity: 0 [*32us]
	Measurement Pilot Transmission:
		 * interval: 0 TUs
	HT capabilities:
		Capabilities: 0x8bc
			HT20
			SM Power Save disabled
			RX Greenfield
			RX HT20 SGI
			TX STBC
			No RX STBC
			Max AMSDU length: 7935 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 1
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 1
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * BSS Transition
		 * Operating Mode Notification
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Version2: 2.0
	WPA:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS ec:6c:9a:39:b0:c2(on wlp2s0)
	TSF: 1210669158809 usec (14d, 00:17:49)
	freq: 2437
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
	signal: -92.00 dBm
	last seen: 704 ms ago
	SSID: Livebox-D910
	Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0* 9.0* 12.0* 18.0* 
	DS Parameter set: channel 6
	TIM: DTIM Count 2 DTIM Period 3 Bitmap Control 0x0 Bitmap[0] 0x0
	Country: FR	Environment: Indoor/Outdoor
		Channels [1 - 13] @ 30 dBm
	Power constraint: 0 dB
	TPC report: TX power: 20 dBm
	ERP: Barker_Preamble_Mode
	Extended supported rates: 24.0* 36.0* 48.0* 54.0* 
	BSS Load:
		 * station count: 2
		 * channel utilisation: 42/255
		 * available admission capacity: 0 [*32us]
	RM enabled capabilities:
		Capabilities: 0x73 0x00 0x01 0x00 0x00
			Link Measurement
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
			Beacon Table Measurement
			AP Channel Report
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0x19ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 7935 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 16 usec (0x07)
		HT RX MCS rate indexes supported: 0-15
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 6
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Version2: 2.0
	Extended capabilities:
		 * BSS Transition
BSS 00:06:91:c8:29:b0(on wlp2s0)
	TSF: 2291132504592 usec (26d, 12:25:32)
	freq: 2462
	beacon interval: 100 TUs
	capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
	signal: -94.00 dBm
	last seen: 360 ms ago
	Information elements from Probe Response frame:
	SSID: SFR_29AF
	Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0 
	DS Parameter set: channel 11
	TPC report: TX power: 20 dBm
	ERP: Barker_Preamble_Mode
	Extended supported rates: 6.0 9.0 12.0 48.0 
	RSN:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC MFP-capable (0x008c)
	BSS Load:
		 * station count: 0
		 * channel utilisation: 71/255
		 * available admission capacity: 0 [*32us]
	RM enabled capabilities:
		Capabilities: 0x32 0x00 0x00 0x00 0x00
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	AP Channel Report:
		 * operating class: 128
		 * channel(s): 100
	HT capabilities:
		Capabilities: 0x1ad
			RX LDPC
			HT20
			SM Power Save disabled
			RX HT20 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-31
		HT TX MCS rate indexes are undefined
	HT operation:
		 * primary channel: 11
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 1
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * Extended Channel Switching
		 * Event
		 * BSS Transition
		 * Interworking
		 * QoS Map
		 * Operating Mode Notification
		 * Reserved Reserved Channel Schedule Management
		 * Reserved Channel Schedule Management
		 * 6
	802.11u Interworking:
		Network Options: 0x0
			Network Type: 0 (Private)
	802.11u Advertisement:
		Query Response Info: 0x7f
			Query Response Length Limit: 127
			ANQP
	WPS:	 * Version: 1.0
		 * Wi-Fi Protected Setup State: 2 (Configured)
		 * Response Type: 3 (AP)
		 * UUID: b45ea7c6-7577-ad34-9241-fd2fb545a995
		 * Manufacturer: AlticeLabs
		 * Model: AlticeLabs GR120DG
		 * Model Number: GR120DG
		 * Serial Number: 5054494E91C829AF
		 * Primary Device Type: 6-0050f204-1
		 * Device name: FiberGateway
		 * Config methods: Display
		 * RF Bands: 0x3
		 * Version2: 2.0
	WPA:	 * Version: 1
		 * Group cipher: CCMP
		 * Pairwise ciphers: CCMP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * u-APSD
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS e4:9e:12:10:b5:77(on wlp2s0)
	TSF: 856185062751 usec (9d, 21:49:45)
	freq: 2472
	beacon interval: 120 TUs
	capability: ESS Privacy ShortSlotTime RadioMeasure (0x1411)
	signal: -94.00 dBm
	last seen: 140 ms ago
	SSID: BOX_embu
	Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0 
	DS Parameter set: channel 13
	TIM: DTIM Count 0 DTIM Period 2 Bitmap Control 0x0 Bitmap[0] 0x0
	ERP: Barker_Preamble_Mode
	Extended supported rates: 24.0 36.0 48.0 54.0 
	RSN:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
		 * Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
	BSS Load:
		 * station count: 0
		 * channel utilisation: 62/255
		 * available admission capacity: 0 [*32us]
	RM enabled capabilities:
		Capabilities: 0x72 0x00 0x00 0x00 0x00
			Neighbor Report
			Beacon Passive Measurement
			Beacon Active Measurement
			Beacon Table Measurement
		Nonoperating Channel Max Measurement Duration: 0
		Measurement Pilot Capability: 0
	HT capabilities:
		Capabilities: 0xec
			HT20
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			No RX STBC
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: No restriction (0x00)
		HT TX/RX MCS rate indexes supported: 0-23, 32
	HT operation:
		 * primary channel: 13
		 * secondary channel offset: no secondary
		 * STA channel width: 20 MHz
		 * RIFS: 0
		 * HT protection: no
		 * non-GF present: 0
		 * OBSS non-GF present: 0
		 * dual beacon: 0
		 * dual CTS protection: 0
		 * STBC beacon: 0
		 * L-SIG TXOP Prot: 0
		 * PCO active: 0
		 * PCO phase: 0
	Extended capabilities:
		 * BSS Transition
		 * SSID List
		 * Operating Mode Notification
	WPA:	 * Version: 1
		 * Group cipher: TKIP
		 * Pairwise ciphers: CCMP TKIP
		 * Authentication suites: PSK
	WMM:	 * Parameter version 1
		 * BE: CW 15-1023, AIFSN 3
		 * BK: CW 15-1023, AIFSN 7
		 * VI: CW 7-15, AIFSN 2, TXOP 3008 usec
		 * VO: CW 3-7, AIFSN 2, TXOP 1504 usec
joel@joel-k70ij:~$ 

Désolé pour la taille du copier coller, il y a moyen de réduire ?

@Verner : oui je suis bien sous Bullseye, en simple boot

joel@joel-k70ij:~$ /sbin/iwlist wlp2s0 channel
wlp2s0    14 channels in total; available frequencies :
          Channel 01 : 2.412 GHz
          Channel 02 : 2.417 GHz
          Channel 03 : 2.422 GHz
          Channel 04 : 2.427 GHz
          Channel 05 : 2.432 GHz
          Channel 06 : 2.437 GHz
          Channel 07 : 2.442 GHz
          Channel 08 : 2.447 GHz
          Channel 09 : 2.452 GHz
          Channel 10 : 2.457 GHz
          Channel 11 : 2.462 GHz
          Channel 12 : 2.467 GHz
          Channel 13 : 2.472 GHz
          Channel 14 : 2.484 GHz
joel@joel-k70ij:~$
joel@joel-k70ij:~$ /sbin/iwlist wlp2s0 scanning |grep ESSID
joel@joel-k70ij:~$

Avec ces questions/réponses croisées dans tous les sens, ça va vite s’embrouiller.
Comme il y a du monde maintenant subitement ré-interessé par ton problème, pas la peine d’être plusieurs, d’autant plus que tu en oublies en cours de route, genre:

–>> « Confirmes-tu que ton wifi fonctionnait parfaitement avec la box précédente sans les firmware atheros ??? »
ou encore
/sbin/iwlist wlp2s0 auth

Continuez tranquillement jusqu’à résolution.

@Verner Désolé pour les oublis

  • oui le wifi marchait avec la box précédente sans les firmwares atheros
joel@joel-k70ij:~$ /sbin/iwlist wlp2s0 auth
wlp2s0    Authentication capabilities :
                WPA
                WPA2
                CIPHER-TKIP
                CIPHER-CCMP

joel@joel-k70ij:~$

J’ai installé les firmwares-atheros

joel@joel-k70ij:~$ sudo apt install firmware-atheros
......
Sélection du paquet firmware-atheros précédemment désélectionné.
(Lecture de la base de données... 160101 fichiers et répertoires déjà installés.)
Préparation du dépaquetage de .../firmware-atheros_20210315-3_all.deb ...
Dépaquetage de firmware-atheros (20210315-3) ...
Paramétrage de firmware-atheros (20210315-3) ...

joel@joel-k70ij:~$ ls /lib/firmware/ath9k*
htc_7010-1.4.0.fw  htc_9271-1.4.0.fw
joel@joel-k70ij:~$

C’est bizarre je ne vois pas le post de Clochette annoncé dans mes sujets
je suis allé voir cette doc debian facile
et je lis :

Depuis Debian 11 bullseye, à condition d’avoir installé auparavant les dépôts non-free à votre fichier /etc/apt/sources.list, un paquet permettrait de trouver et d’installer automatiquement les firmwares manquants : isenkram-cli
apt install isenkram-cli
isenkram-autoinstall-firmware
mon fichier sources.list a l’air de bien contenir les dépôts non-free

deb http://deb.debian.org/debian bullseye main contrib non-free
#deb-src http://deb.debian.org/debian bullseye main contrib non-free

deb http://deb.debian.org/debian-security/ bullseye-security main contrib non-free
#deb-src http://deb.debian.org/debian-security/ bullseye-security main contrib non-free

deb http://deb.debian.org/debian bullseye-updates main contrib non-free
#deb-src http://deb.debian.org/debian bullseye-updates main contrib non-free

je n’ose pas taper ces commandes ayant déjà installé firmware-atheros
merci

C’est normal, c’est une modification de tes message pour faire la mise en forme des retours de commandes, n’hésite pas à jeter un œil aux modification faites par la modération.

Concernant les firmwares, je ne sais pas s’ils était nécessaires, mais tes retours de commandes laissent penser que le matériel est maintenant opérationnel.
Essaie la commande suivante en remplaçant <ssid> par le nom de ton réseau.

sudo iw dev wlp2s0 scan | grep -i "<ssid>"

Si ton point d’accès apparaît dans le retour de la commande, c’est que ta carte Wifi voit bien le point d’accès, sinon, ce n’est pas le cas.

joel@joel-k70ij:~$ sudo iw dev wlp2s0 scan | grep -i "Livebox-9C90"
	SSID: Livebox-9C90
joel@joel-k70ij:~$

La box est donc bien détectée mais toujours pas de connexion. J’ai essayé WPA + WPA 2 personnel ainsi que WPA3 sans résultat
Aucun des autres choix ne fonctionne non plus

  • clé WEP 40/128 bit
  • WEP 128 bit à phrase secrète
  • LEAP
  • WEP dynamique
  • Enhanced Open
    En fait je comprends que la box était détectée depuis le début puisqu’elle a toujours figuré dans la liste des connexions, sauf qu’il y a la mention : jamais dans la colonne « dernière connexion » . Finalement, que les firmware soient installés ou non ne change rien
    Je reprends une réflexion de Verner :

oui je confirme bien que ça marchait avant sans les firmware atheros

Je me demande quels firmwares manquants les commandes indiquées permettent d’installer. Des firmwares différents des firmwares atheros ?

Attention ath9k c’est aussi firmware-ath9k-htc

Quel est l’intérêt de tenter ces commandes ?
Y a-t-il un risque à le faire ?
Merci

Bonjour
J’ai installé le paquet
isenkram-cli puis installé les firmware
sudo isenkram-autoinstall-firmware
et remis le mot de passe wifi avec la clé WAP et WPA2 personnel
pas de résultat

7 jours après je vais reposer les mêmes questions du coup.

Bonjour Clochette
Je ne sais pas comment te répondre, par exemple où trouver les logs
Pour me connecter j’utilise mon vieux PC Asus de 2009 sous Bullseye
j’ai trouvé une adresse MAC sur la box, je ne sais pas comment l’utiliser ni même si c’est nécessaire, ce n’était pas le cas avec l’ancienne box Free
merci

Sur les livebox tu as un filtrage des mac disponible, il te faut te connecter à l’interface depuis l’ip 192.168.1.1 et vérifie déjà ce point, ensuite sur les version livebox 4 était disponible un bouton à appuyer pour permettre l’appairage des éléments fonctionnant en wifi tel que les décodeurs, téléphones etc … ) cela fait donc un second point à vérifier.

Tu précise être sur Bullseye, très bien mais avec quoi te connectes-tu ? Networkmanager ?

Si c’est le cas alors il te faudra ta clé wpa, tu sélectionnera ton SSID et tu remplieras ce qu’il faut.
Si jamais tu désire un poil plus de liberté laisse la configuration en DHCP mais utilise des DNS autres que ceux du FAI, tel que 1.1.1.1 par exemple et laisse la configuration de la route en automatique.

Si tu est en ipv6 alors adapte l’ipv6 pour la partie dns (pour cloudflare ce doit-être 2606:4700:4700::1111 ).

Tu as perdu 7 jours car tu ne précise pas assez les outils que tu utilise et tout le monde finalement est parti sur une fausse piste avec le firmware.

Si tu arrive à détecter les SSID des réseau wifi alors il est envisageable que le problème soit plus de l’ordre du blocage ou de la mauvaise configuration de la connexion (erreur wpa, blocage mac par le routeur, etc …).

Bonjour
L’important pour moi n’est pas de gagner 7 jours mais d’apprendre à bien poser mes questions, et parfois aussi comprendre les réponses :>))
Networkmanager n’est pas installé sur ma machine, faut-il l’installer ?
‹ joel@joel-k70ij:~$ networkmanager
bash: networkmanager : commande introuvable ›
Je regarde la configuration de la connexion ouvrant " connexions réseau " dans le menu des applications
voici l’état actuel :








Pour vérifier qu’un paquet est installé il suffit en règle générale de vérifier la version candidate :

apt policy network-manager

Si tu cherche des paquets depuis le terminal ce sera ainsi :

apt search network-manager

ça ressemble bien à Network manager ce que tu nous montre par contre pour le wifi à moins de savoir ce que l’on fait en laisse en automatique.
Tu doit avoir une applet réseaux sur ton bureau, il te suffit en générale de sélectionner le réseau wifi voulu et rentrer tes identifiants, tu fini par enregistré pour la prochaine connexion et basta.

Avec les livebox comme expliqué précédemment tu as une mécanique qui peux réclamer lors de la première connexion de passer en mode association/appairage, une fois connecté tu pourras après coup enregistrer la MAC pour permettre de sécuriser un minimum le wifi et empêcher d’autre appareils de se connecter.

Pour te connecter sur l’interface utilise un câble ethernet temporairement et rends toi sur https://192.168.1.1 pour gérer les accès diffusion SSID etc …

Je suis allé sur l’interface et j’ai trouvé solution au moins provisoire : en attendant mieux j’ai créé une connexion invité, l’interface m’a donné une clé WPA + WPA2.
La question est de savoir si c’est aussi bien sécurisé qu’une connexion normale