Bonjour
je viens d’installer Debian Lenny sur un portable D610, et j’ai voulu faire marcher le wifi.
Bon j’y ai passé toute la journée et ca ne marche pas …
la carte semble reconnu en tout cas elle apparait avec lspci
mais je ne vois aucun reseau, et meme en essayant de me connecter a mon reseau (qui est vsible) ca ne marche pas.
Je sais pas du tout quoi faire …
Si quelqu’un a une ptite idée …
Que renvoie lspci, dmesg, ifconfig, ifconfig -a et iwconfig ?
Bon entre temps j’ai réinstallé Debian pour avoir un systeme tout neuf (j’avai essayé d’installer les drivers etc d’apres different tuto, sauf que pour ieee80211 et ipw2200 impossible de compiler etc …)
Donc voici les resultat
lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 03)
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 01)
03:01.0 CardBus bridge: Texas Instruments PCI6515 Cardbus Controller
03:01.5 Communication controller: Texas Instruments PCI6515 SmartCard Controller
03:03.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-13) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f7d1800 (usable)
[ 0.000000] BIOS-e820: 000000003f7d1800 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] 119MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 260049) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 260049
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 260049
[ 0.000000] On node 0 totalpages: 260049
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 240 pages used for memmap
[ 0.000000] HighMem zone: 30433 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FC9B0, 0014 (r0 DELL )
[ 0.000000] ACPI: RSDT 3F7D1F90, 0040 (r1 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: FACP 3F7D2C00, 0074 (r1 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: DSDT 3F7D3800, 3C51 (r1 INT430 SYSFexxx 1001 MSFT 100000E)
[ 0.000000] ACPI: FACS 3F7E2000, 0040
[ 0.000000] ACPI: APIC 3F7D3400, 0068 (r1 DELL CPi R 27D50A02 ASL 47)
[ 0.000000] ACPI: ASF! 3F7D3000, 005B (r16 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: MCFG 3F7D33C0, 003E (r16 DELL CPi R 27D50A02 ASL 61)
[ 0.000000] ACPI: SSDT 3F7D23E6, 0280 (r1 PmRef Cpu0Ist 3000 INTL 20030522)
[ 0.000000] ACPI: SSDT 3F7D220E, 01D8 (r1 PmRef Cpu0Cst 3001 INTL 20030522)
[ 0.000000] ACPI: SSDT 3F7D2013, 01FB (r1 PmRef CpuPm 3000 INTL 20030522)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 258017
[ 0.000000] Kernel command line: root=/dev/sda6 ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1862.051 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 1021156k/1040196k available (1769k kernel code, 18328k reserved, 752k data, 244k init, 122692k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba4ab - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba4ab (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084009] Calibrating delay using timer specific routine.. 3728.43 BogoMIPS (lpj=7456871)
[ 0.084046] Security Framework initialized
[ 0.084052] SELinux: Disabled at boot.
[ 0.084056] Capability LSM initialized
[ 0.084072] Mount-cache hash table entries: 512
[ 0.084210] Initializing cgroup subsys ns
[ 0.084214] Initializing cgroup subsys cpuacct
[ 0.084217] Initializing cgroup subsys devices
[ 0.084238] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084241] CPU: L2 cache: 2048K
[ 0.084246] Intel machine check architecture supported.
[ 0.084251] Intel machine check reporting enabled on CPU#0.
[ 0.084262] Checking 'hlt' instruction... OK.
[ 0.100304] SMP alternatives: switching to UP code
[ 0.105188] ACPI: Core revision 20080321
[ 0.115103] ENABLING IO-APIC IRQs
[ 0.115303] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.155048] CPU0: Intel(R) Pentium(R) M processor 1.86GHz stepping 08
[ 0.156009] Brought up 1 CPUs
[ 0.156009] Total of 1 processors activated (3728.43 BogoMIPS).
[ 0.156009] CPU0 attaching sched-domain:
[ 0.156009] domain 0: span 0
[ 0.156009] groups: 0
[ 0.156009] net_namespace: 660 bytes
[ 0.156009] Booting paravirtualized kernel on bare hardware
[ 0.156009] NET: Registered protocol family 16
[ 0.156009] ACPI: bus type pci registered
[ 0.156009] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.156009] PCI: MCFG area at e0000000 reserved in E820
[ 0.156009] PCI: Using MMCONFIG for extended config space
[ 0.156009] PCI: Using configuration type 1 for base access
[ 0.156009] Setting up standard PCI resources
[ 0.156010] ACPI: EC: Look up EC in DSDT
[ 0.177902] ACPI: SSDT 3F7D1FD0, 0043 (r1 LMPWR DELLLOM 1001 INTL 20030522)
[ 0.178455] ACPI: Interpreter enabled
[ 0.178459] ACPI: (supports S0 S3 S4 S5)
[ 0.178472] ACPI: Using IOAPIC for interrupt routing
[ 0.209582] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.210353] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.210360] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 0.210365] pci 0000:00:1f.0: quirk: region 1080-10bf claimed by ICH6 GPIO
[ 0.210870] PCI: Transparent bridge - 0000:00:1e.0
[ 0.210919] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.211351] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
[ 0.230691] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
[ 0.230811] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10
[ 0.230929] ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11)
[ 0.231045] ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
[ 0.231147] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.231253] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.231359] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.231561] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.231588] pnp: PnP ACPI init
[ 0.231594] ACPI: bus type pnp registered
[ 0.297706] pnp 00:0f: can't add resource for IO 0x57b0-0x57bb
[ 0.298730] pnp: PnP ACPI: found 16 devices
[ 0.298733] ACPI: ACPI bus type pnp unregistered
[ 0.298736] PnPBIOS: Disabled by ACPI PNP
[ 0.298956] PCI: Using ACPI for IRQ routing
[ 0.299208] hpet clockevent registered
[ 0.299215] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.299219] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.300284] system 00:00: iomem range 0x0-0x9fbff could not be reserved
[ 0.300287] system 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
[ 0.300290] system 00:00: iomem range 0xc0000-0xcffff could not be reserved
[ 0.300293] system 00:00: iomem range 0xe0000-0xfffff could not be reserved
[ 0.300296] system 00:00: iomem range 0x100000-0x3f7d17ff could not be reserved
[ 0.300299] system 00:00: iomem range 0x3f7d1800-0x3f7fffff could not be reserved
[ 0.300302] system 00:00: iomem range 0x3f800000-0x3fffffff could not be reserved
[ 0.300306] system 00:00: iomem range 0xfeda0000-0xfedfffff could not be reserved
[ 0.300309] system 00:00: iomem range 0xffb00000-0xffffffff could not be reserved
[ 0.300312] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.300315] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.300318] system 00:00: iomem range 0xfed20000-0xfed9ffff could not be reserved
[ 0.300321] system 00:00: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 0.300324] system 00:00: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 0.300327] system 00:00: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 0.300330] system 00:00: iomem range 0xf0006000-0xf0006fff could not be reserved
[ 0.300334] system 00:00: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 0.300337] system 00:00: iomem range 0xe0000000-0xefffffff could not be reserved
[ 0.300343] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.300346] system 00:02: ioport range 0x1000-0x1005 has been reserved
[ 0.300349] system 00:02: ioport range 0x1008-0x100f has been reserved
[ 0.300355] system 00:03: ioport range 0xf400-0xf4fe has been reserved
[ 0.300357] system 00:03: ioport range 0x1006-0x1007 has been reserved
[ 0.300360] system 00:03: ioport range 0x100a-0x1059 could not be reserved
[ 0.300363] system 00:03: ioport range 0x1060-0x107f has been reserved
[ 0.300366] system 00:03: ioport range 0x1080-0x10bf has been reserved
[ 0.300369] system 00:03: ioport range 0x10c0-0x10df has been reserved
[ 0.300372] system 00:03: ioport range 0x10e0-0x10ff has been reserved
[ 0.300379] system 00:08: ioport range 0x900-0x90f has been reserved
[ 0.300382] system 00:08: ioport range 0x910-0x91f has been reserved
[ 0.300385] system 00:08: ioport range 0x920-0x92f has been reserved
[ 0.300387] system 00:08: ioport range 0x93c-0x93f has been reserved
[ 0.300390] system 00:08: ioport range 0x940-0x97f has been reserved
[ 0.300398] system 00:0e: ioport range 0x930-0x93b has been reserved
[ 0.300403] system 00:0f: ioport range 0x7b0-0x7bb has been reserved
[ 0.300406] system 00:0f: ioport range 0x7c0-0x7df has been reserved
[ 0.300409] system 00:0f: ioport range 0xbb0-0xbbb has been reserved
[ 0.300412] system 00:0f: ioport range 0xbc0-0xbdf has been reserved
[ 0.300414] system 00:0f: ioport range 0xfb0-0xfbb has been reserved
[ 0.300417] system 00:0f: ioport range 0xfc0-0xfdf has been reserved
[ 0.300421] system 00:0f: ioport range 0x13b0-0x13bb has been reserved
[ 0.300423] system 00:0f: ioport range 0x13c0-0x13df has been reserved
[ 0.300426] system 00:0f: ioport range 0x17b0-0x17bb has been reserved
[ 0.300429] system 00:0f: ioport range 0x17c0-0x17df has been reserved
[ 0.300432] system 00:0f: ioport range 0x1bb0-0x1bbb has been reserved
[ 0.300435] system 00:0f: ioport range 0x1bc0-0x1bdf has been reserved
[ 0.300438] system 00:0f: ioport range 0x1fb0-0x1fbb has been reserved
[ 0.300441] system 00:0f: ioport range 0x1fc0-0x1fdf has been reserved
[ 0.300443] system 00:0f: ioport range 0x23b0-0x23bb has been reserved
[ 0.300446] system 00:0f: ioport range 0x23c0-0x23df has been reserved
[ 0.300449] system 00:0f: ioport range 0x27b0-0x27bb has been reserved
[ 0.300452] system 00:0f: ioport range 0x27c0-0x27df has been reserved
[ 0.300455] system 00:0f: ioport range 0x2bb0-0x2bbb has been reserved
[ 0.300458] system 00:0f: ioport range 0x2bc0-0x2bdf has been reserved
[ 0.300461] system 00:0f: ioport range 0x2fb0-0x2fbb has been reserved
[ 0.300464] system 00:0f: ioport range 0x2fc0-0x2fdf has been reserved
[ 0.300466] system 00:0f: ioport range 0x33b0-0x33bb has been reserved
[ 0.300469] system 00:0f: ioport range 0x33c0-0x33df has been reserved
[ 0.300472] system 00:0f: ioport range 0x37b0-0x37bb has been reserved
[ 0.300475] system 00:0f: ioport range 0x37c0-0x37df has been reserved
[ 0.300478] system 00:0f: ioport range 0x3bb0-0x3bbb has been reserved
[ 0.300481] system 00:0f: ioport range 0x3bc0-0x3bdf has been reserved
[ 0.300484] system 00:0f: ioport range 0x3fb0-0x3fbb has been reserved
[ 0.300487] system 00:0f: ioport range 0x3fc0-0x3fdf has been reserved
[ 0.300490] system 00:0f: ioport range 0x43b0-0x43bb has been reserved
[ 0.300492] system 00:0f: ioport range 0x43c0-0x43df has been reserved
[ 0.300497] system 00:0f: ioport range 0x47b0-0x47bb has been reserved
[ 0.300500] system 00:0f: ioport range 0x47c0-0x47df has been reserved
[ 0.300503] system 00:0f: ioport range 0x4bb0-0x4bbb has been reserved
[ 0.300506] system 00:0f: ioport range 0x4bc0-0x4bdf has been reserved
[ 0.300509] system 00:0f: ioport range 0x4fb0-0x4fbb has been reserved
[ 0.300512] system 00:0f: ioport range 0x4fc0-0x4fdf has been reserved
[ 0.300515] system 00:0f: ioport range 0x53b0-0x53bb has been reserved
[ 0.300518] system 00:0f: ioport range 0x53c0-0x53df has been reserved
[ 0.330885] PCI: region 0000:03:01.0/9 too large: 0x0000000000000000-0x0000000003ffffff
[ 0.330893] PCI: Bridge: 0000:00:1c.0
[ 0.330895] IO window: disabled.
[ 0.330901] MEM window: 0xdfd00000-0xdfdfffff
[ 0.330905] PREFETCH window: disabled.
[ 0.330917] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[ 0.330919] IO window: 0x00006000-0x000060ff
[ 0.330924] IO window: 0x00006400-0x000064ff
[ 0.330930] MEM window: 0x50000000-0x53ffffff
[ 0.330936] PCI: Bridge: 0000:00:1e.0
[ 0.330939] IO window: 6000-6fff
[ 0.330944] MEM window: 0xdfc00000-0xdfcfffff
[ 0.330949] PREFETCH window: disabled.
[ 0.330977] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.330984] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.330997] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.331013] pci 0000:03:01.0: enabling device (0000 -> 0003)
[ 0.331018] ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 0.331043] NET: Registered protocol family 2
[ 0.331126] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.331344] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.332275] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.332884] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.332888] TCP reno registered
[ 0.333044] NET: Registered protocol family 1
[ 0.333170] checking if image is initramfs... it is
[ 0.800038] Switched to high resolution mode on CPU 0
[ 0.852117] Freeing initrd memory: 6059k freed
[ 0.852765] audit: initializing netlink socket (disabled)
[ 0.852786] type=2000 audit(1235314522.852:1): initialized
[ 0.852947] highmem bounce pool size: 64 pages
[ 0.852952] Total HugeTLB memory allocated, 0
[ 0.853036] VFS: Disk quotas dquot_6.5.1
[ 0.853066] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.853107] msgmni has been set to 1767
[ 0.853226] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.853231] io scheduler noop registered
[ 0.853233] io scheduler anticipatory registered
[ 0.853234] io scheduler deadline registered
[ 0.853252] io scheduler cfq registered (default)
[ 0.853267] pci 0000:00:02.0: Boot video device
[ 0.853463] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.853507] assign_interrupt_mode Found MSI capability
[ 0.853552] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.853589] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.853624] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.853926] isapnp: Scanning for PnP cards...
[ 1.208138] isapnp: No Plug & Play device found
[ 1.210440] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.210580] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.210753] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
[ 1.211101] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.211235] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 1.211243] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 1.212487] brd: module loaded
[ 1.212577] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.217489] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.217494] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.217622] mice: PS/2 mouse device common for all mice
[ 1.217732] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.217754] rtc0: alarms up to one month, y3k
[ 1.217784] cpuidle: using governor ladder
[ 1.217786] cpuidle: using governor menu
[ 1.217790] No iBFT detected.
[ 1.218196] TCP cubic registered
[ 1.218199] NET: Registered protocol family 17
[ 1.218205] Using IPI No-Shortcut mode
[ 1.218312] registered taskstats version 1
[ 1.218461] rtc_cmos 00:06: setting system clock to 2009-02-22 14:55:23 UTC (1235314523)
[ 1.218594] Freeing unused kernel memory: 244k freed
[ 1.222361] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.302137] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 1.302178] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.302182] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 1.304929] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 1.306430] ACPI: Thermal Zone [THM] (60 C)
[ 1.830443] ACPI: ACPI Dock Station Driver
[ 1.860296] tg3.c:v3.92.1 (June 9, 2008)
[ 1.860329] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.860339] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1.882606] eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCI Express) 10/100/1000Base-T Ethernet 00:12:3f:1f:45:0e
[ 1.882612] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
[ 1.882615] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.888148] usbcore: registered new interface driver usbfs
[ 1.888176] usbcore: registered new interface driver hub
[ 1.888202] usbcore: registered new device driver usb
[ 1.889223] USB Universal Host Controller Interface driver v3.0
[ 1.889265] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.889279] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.889283] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.889413] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 1.889446] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000bf80
[ 1.889519] usb usb1: configuration #1 chosen from 1 choice
[ 1.889545] hub 1-0:1.0: USB hub found
[ 1.889551] hub 1-0:1.0: 2 ports detected
[ 1.992127] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.992131] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.992134] usb usb1: Product: UHCI Host Controller
[ 1.992136] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.992138] usb usb1: SerialNumber: 0000:00:1d.0
[ 1.992179] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 1.992192] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 1.992196] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.992219] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 1.992254] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60
[ 1.992333] usb usb2: configuration #1 chosen from 1 choice
[ 1.992360] hub 2-0:1.0: USB hub found
[ 1.992366] hub 2-0:1.0: 2 ports detected
[ 2.048241] SCSI subsystem initialized
[ 2.070936] libata version 3.00 loaded.
[ 2.096115] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.096119] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.096123] usb usb2: Product: UHCI Host Controller
[ 2.096125] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.096128] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.096180] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.096193] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.096197] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.096221] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.096255] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40
[ 2.096334] usb usb3: configuration #1 chosen from 1 choice
[ 2.096364] hub 3-0:1.0: USB hub found
[ 2.096370] hub 3-0:1.0: 2 ports detected
[ 2.200111] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.200116] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.200119] usb usb3: Product: UHCI Host Controller
[ 2.200121] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.200123] usb usb3: SerialNumber: 0000:00:1d.2
[ 2.200173] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 2.200187] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 2.200192] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 2.200220] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 2.200256] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000bf20
[ 2.200332] usb usb4: configuration #1 chosen from 1 choice
[ 2.200358] hub 4-0:1.0: USB hub found
[ 2.200365] hub 4-0:1.0: 2 ports detected
[ 2.201771] Marking TSC unstable due to: TSC halts in idle.
[ 2.418825] Clocksource tsc unstable (delta = -212199850 ns)
[ 2.426778] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.426778] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.426778] usb usb4: Product: UHCI Host Controller
[ 2.426778] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.426778] usb usb4: SerialNumber: 0000:00:1d.3
[ 2.426778] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.426778] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.426778] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.426778] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 2.426778] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.426778] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.426778] ehci_hcd 0000:00:1d.7: irq 16, io mem 0xffa80800
[ 2.438184] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.438184] usb usb5: configuration #1 chosen from 1 choice
[ 2.438184] hub 5-0:1.0: USB hub found
[ 2.438184] hub 5-0:1.0: 8 ports detected
[ 2.541500] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.541500] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.541500] usb usb5: Product: EHCI Host Controller
[ 2.541500] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.541500] usb usb5: SerialNumber: 0000:00:1d.7
[ 2.541500] ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 2.541500] ssb: Sonics Silicon Backplane found on PCI device 0000:03:03.0
[ 2.541500] ata_piix 0000:00:1f.2: version 2.12
[ 2.541500] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 2.541500] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 2.588035] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.588194] scsi0 : ata_piix
[ 2.588299] scsi1 : ata_piix
[ 2.590350] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xbfa0 irq 14
[ 2.590354] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xbfa8 irq 15
[ 2.752601] ata1.00: ATA-6: TOSHIBA MK4026GAX, PA102D, max UDMA/100
[ 2.752605] ata1.00: 78140160 sectors, multi 8: LBA
[ 2.752608] ata1.00: applying bridge limits
[ 2.760602] ata1.00: configured for UDMA/100
[ 2.924458] ata2.00: ATAPI: PHILIPS CD-RW/DVD-ROM SCB5265, TD15, max UDMA/33
[ 2.940393] ata2.00: configured for UDMA/33
[ 2.940506] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4026GA PA10 PQ: 0 ANSI: 5
[ 2.941188] scsi 1:0:0:0: CD-ROM PHILIPS CDRW/DVD SCB5265 TD15 PQ: 0 ANSI: 5
[ 2.949785] Uniform Multi-Platform E-IDE driver
[ 2.949788] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 2.979122] Driver 'sd' needs updating - please use bus_type methods
[ 2.979229] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[ 2.979250] sd 0:0:0:0: [sda] Write Protect is off
[ 2.979252] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.979286] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.979351] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[ 2.979370] sd 0:0:0:0: [sda] Write Protect is off
[ 2.979372] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.979406] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.979410] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 3.031775] sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 >
[ 3.110581] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.118755] sr0: scsi3-mmc drive: 4x/24x writer cd/rw xa/form2 cdda tray
[ 3.118760] Uniform CD-ROM driver Revision: 3.20
[ 3.118828] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.130095] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.130117] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.538770] kjournald starting. Commit interval 5 seconds
[ 3.538770] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.366392] udevd version 125 started
[ 6.080122] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 6.174740] Linux agpgart interface v0.103
[ 6.176710] agpgart: Detected an Intel 915GM Chipset.
[ 6.177099] agpgart: Detected 7932K stolen memory.
[ 6.193597] agpgart: AGP aperture is 256M @ 0xc0000000
[ 6.617623] ACPI: AC Adapter [AC] (on-line)
[ 6.944419] ACPI: Battery Slot [BAT0] (battery present)
[ 6.944528] ACPI: Battery Slot [BAT1] (battery absent)
[ 6.944614] input: Lid Switch as /class/input/input1
[ 6.960485] ACPI: Lid Switch [LID]
[ 6.960542] input: Power Button (CM) as /class/input/input2
[ 6.988049] ACPI: Power Button (CM) [PBTN]
[ 6.988462] input: Sleep Button (CM) as /class/input/input3
[ 7.016057] ACPI: Sleep Button (CM) [SBTN]
[ 7.602887] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
[ 7.602893] ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
[ 7.602922] ACPI: Error installing bay notify handler
[ 7.646416] input: Video Bus as /class/input/input4
[ 7.676066] ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
[ 7.676553] input: Video Bus as /class/input/input5
[ 7.708057] ACPI: Video Device [VID1] (multi-head: yes rom: no post: no)
[ 7.708201] input: Video Bus as /class/input/input6
[ 7.740052] ACPI: Video Device [VID2] (multi-head: yes rom: no post: no)
[ 8.043622] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 8.043646] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 8.108421] intel_rng: FWH not detected
[ 8.260483] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 8.260562] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 8.260590] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 8.384609] input: PC Speaker as /class/input/input7
[ 8.527359] b43-phy0: Broadcom 4306 WLAN found
[ 8.572561] phy0: Selected rate control algorithm 'pid'
[ 8.853088] NET: Registered protocol family 23
[ 8.868155] intel8x0_measure_ac97_clock: measured 54265 usecs
[ 8.868159] intel8x0: clocking to 48000
[ 8.877490] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 8.877518] PCI: Setting latency timer of device 0000:00:1e.3 to 64
[ 8.878411] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 8.980059] MC'97 1 converters and GPIO not ready (0xff00)
[ 8.980597] Yenta: CardBus bridge found at 0000:03:01.0 [1028:0182]
[ 8.980621] PCI: Bus 4, cardbus bridge: 0000:03:01.0
[ 8.980623] IO window: 0x00006000-0x000060ff
[ 8.980628] IO window: 0x00006400-0x000064ff
[ 8.980634] PREFETCH window: 0x54000000-0x543fffff
[ 8.980639] MEM window: 0x50000000-0x53ffffff
[ 8.980648] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 8.980650] Yenta: Routing CardBus interrupts to PCI
[ 8.980656] Yenta TI: socket 0000:03:01.0, mfunc 0x01111122, devctl 0x64
[ 9.004448] input: PS/2 Mouse as /class/input/input8
[ 9.053190] input: AlpsPS/2 ALPS GlidePoint as /class/input/input9
[ 9.084682] parport_pc 00:0d: reported by Plug and Play ACPI
[ 9.084750] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 9.212704] Yenta: ISA IRQ mask 0x0c78, PCI irq 19
[ 9.212709] Socket status: 30000006
[ 9.212712] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[ 9.212717] pcmcia: parent PCI bridge I/O window: 0x6000 - 0x6fff
[ 9.212720] cs: IO port probe 0x6000-0x6fff: clean.
[ 9.213045] pcmcia: parent PCI bridge Memory window: 0xdfc00000 - 0xdfcfffff
[ 9.800242] cs: IO port probe 0x100-0x3af: excluding 0x290-0x297
[ 9.801908] cs: IO port probe 0x3e0-0x4ff: clean.
[ 9.802568] cs: IO port probe 0x820-0x8ff: clean.
[ 9.803149] cs: IO port probe 0xc00-0xcf7: clean.
[ 9.803839] cs: IO port probe 0xa00-0xaff: clean.
[ 10.811322] EXT3 FS on sda6, internal journal
[ 11.021385] loop: module loaded
[ 12.167378] kjournald starting. Commit interval 5 seconds
[ 12.167453] EXT3 FS on sda9, internal journal
[ 12.167453] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.207033] kjournald starting. Commit interval 5 seconds
[ 12.207211] EXT3 FS on sda8, internal journal
[ 12.207211] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.240075] kjournald starting. Commit interval 5 seconds
[ 12.240148] EXT3 FS on sda7, internal journal
[ 12.240148] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.468760] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 15.468763] tg3: eth0: Flow control is off for TX and off for RX.
[ 17.048953] NET: Registered protocol family 10
[ 17.049390] lo: Disabled Privacy Extensions
[ 17.507575] lp0: using parport0 (interrupt-driven).
[ 17.555503] ppdev: user-space parallel port driver
[ 22.065178] Bluetooth: Core ver 2.11
[ 22.067279] NET: Registered protocol family 31
[ 22.067289] Bluetooth: HCI device and connection manager initialized
[ 22.067295] Bluetooth: HCI socket layer initialized
[ 22.119610] Bluetooth: L2CAP ver 2.9
[ 22.119621] Bluetooth: L2CAP socket layer initialized
[ 22.218451] Bluetooth: RFCOMM socket layer initialized
[ 22.218465] Bluetooth: RFCOMM TTY layer initialized
[ 22.218467] Bluetooth: RFCOMM ver 1.8
[ 22.453029] input: b43-phy0 as /class/input/input10
[ 22.520042] firmware: requesting b43/ucode5.fw
[ 22.621776] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 22.621776] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 25.325523] input: b43-phy0 as /class/input/input11
[ 25.368066] firmware: requesting b43/ucode5.fw
[ 25.375715] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 25.375730] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 27.802760] [drm] Initialized drm 1.1.0 20060810
[ 27.806454] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 27.806463] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 27.806536] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 39.768165] eth0: no IPv6 routers present
[ 42.513700] input: b43-phy0 as /class/input/input12
[ 42.552119] firmware: requesting b43/ucode5.fw
[ 42.559792] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 42.559806] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 59.684878] input: b43-phy0 as /class/input/input13
[ 59.728051] firmware: requesting b43/ucode5.fw
[ 59.732021] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 59.732028] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 76.849637] input: b43-phy0 as /class/input/input14
[ 76.888183] firmware: requesting b43/ucode5.fw
[ 76.896013] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 76.896013] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 94.049665] input: b43-phy0 as /class/input/input15
[ 94.088159] firmware: requesting b43/ucode5.fw
[ 94.095855] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 94.095869] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 111.237604] input: b43-phy0 as /class/input/input16
[ 111.276189] firmware: requesting b43/ucode5.fw
[ 111.283910] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 111.283924] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 128.429794] input: b43-phy0 as /class/input/input17
[ 128.468063] firmware: requesting b43/ucode5.fw
[ 128.475676] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 128.475691] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 145.616793] input: b43-phy0 as /class/input/input18
[ 145.660043] firmware: requesting b43/ucode5.fw
[ 145.663679] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 145.663684] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 267.777478] input: b43-phy0 as /class/input/input19
[ 267.816068] firmware: requesting b43/ucode5.fw
[ 267.823768] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 267.823782] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 389.962942] input: b43-phy0 as /class/input/input20
[ 390.000072] firmware: requesting b43/ucode5.fw
[ 390.004323] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 390.004331] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 512.150063] input: b43-phy0 as /class/input/input21
[ 512.188046] firmware: requesting b43/ucode5.fw
[ 512.197658] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 512.197666] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 634.326949] input: b43-phy0 as /class/input/input22
[ 634.364062] firmware: requesting b43/ucode5.fw
[ 634.371785] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 634.371799] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 756.513488] input: b43-phy0 as /class/input/input23
[ 756.552063] firmware: requesting b43/ucode5.fw
[ 756.559684] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 756.559698] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 878.694111] input: b43-phy0 as /class/input/input24
[ 878.732050] firmware: requesting b43/ucode5.fw
[ 878.735784] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 878.735792] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1000.875311] input: b43-phy0 as /class/input/input25
[ 1000.916043] firmware: requesting b43/ucode5.fw
[ 1000.919868] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1000.919876] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1123.037599] input: b43-phy0 as /class/input/input26
[ 1123.080047] firmware: requesting b43/ucode5.fw
[ 1123.084033] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1123.084041] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1245.201687] input: b43-phy0 as /class/input/input27
[ 1245.240128] firmware: requesting b43/ucode5.fw
[ 1245.247905] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1245.247920] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1367.394885] input: b43-phy0 as /class/input/input28
[ 1367.432063] firmware: requesting b43/ucode5.fw
[ 1367.439762] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1367.439777] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1489.581476] input: b43-phy0 as /class/input/input29
[ 1489.620048] firmware: requesting b43/ucode5.fw
[ 1489.623774] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1489.623782] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1611.759164] input: b43-phy0 as /class/input/input30
[ 1611.800044] firmware: requesting b43/ucode5.fw
[ 1611.803855] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1611.803863] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1733.933610] input: b43-phy0 as /class/input/input31
[ 1733.976044] firmware: requesting b43/ucode5.fw
[ 1733.979738] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1733.979743] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1856.099107] input: b43-phy0 as /class/input/input32
[ 1856.136190] firmware: requesting b43/ucode5.fw
[ 1856.143882] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1856.143896] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 1978.285601] input: b43-phy0 as /class/input/input33
[ 1978.324053] firmware: requesting b43/ucode5.fw
[ 1978.327787] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 1978.327795] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2100.477533] input: b43-phy0 as /class/input/input34
[ 2100.520044] firmware: requesting b43/ucode5.fw
[ 2100.523675] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2100.523681] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2222.641511] input: b43-phy0 as /class/input/input35
[ 2222.680063] firmware: requesting b43/ucode5.fw
[ 2222.687697] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2222.687711] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2344.825612] input: b43-phy0 as /class/input/input36
[ 2344.864136] firmware: requesting b43/ucode5.fw
[ 2344.871755] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2344.871769] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2467.010057] input: b43-phy0 as /class/input/input37
[ 2467.048056] firmware: requesting b43/ucode5.fw
[ 2467.051786] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2467.051794] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2589.193710] input: b43-phy0 as /class/input/input38
[ 2589.232135] firmware: requesting b43/ucode5.fw
[ 2589.240903] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2589.240917] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2596.452171] tg3: eth0: Link is down.
[ 2611.377653] input: b43-phy0 as /class/input/input39
[ 2611.416178] firmware: requesting b43/ucode5.fw
[ 2611.423817] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2611.423832] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2633.573661] input: b43-phy0 as /class/input/input40
[ 2633.612189] firmware: requesting b43/ucode5.fw
[ 2633.620012] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2633.620012] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2655.757608] input: b43-phy0 as /class/input/input41
[ 2655.796189] firmware: requesting b43/ucode5.fw
[ 2655.803897] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2655.803911] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2675.696186] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 2675.870730] usb 3-1: configuration #1 chosen from 1 choice
[ 2675.874807] usb 3-1: New USB device found, idVendor=046d, idProduct=c00c
[ 2675.874818] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2675.874825] usb 3-1: Product: USB Optical Mouse
[ 2675.874829] usb 3-1: Manufacturer: Logitech
[ 2675.996595] usbcore: registered new interface driver hiddev
[ 2676.009189] input: Logitech USB Optical Mouse as /class/input/input42
[ 2676.009189] input,hidraw0: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.2-1
[ 2676.009189] usbcore: registered new interface driver usbhid
[ 2676.009189] usbhid: v2.6:USB HID core driver
[ 2677.945733] input: b43-phy0 as /class/input/input43
[ 2677.988055] firmware: requesting b43/ucode5.fw
[ 2677.991929] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2677.991936] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2700.133716] input: b43-phy0 as /class/input/input44
[ 2700.172050] firmware: requesting b43/ucode5.fw
[ 2700.175900] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2700.175907] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
[ 2722.313670] input: b43-phy0 as /class/input/input45
[ 2722.356043] firmware: requesting b43/ucode5.fw
[ 2722.359705] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed.
[ 2722.359711] b43-phy0 ERROR: You must go to http://linuxwireless.org/en/users/Drivers/b43#devicefirmware and download the latest firmware (version 4).
ifconfig
[code]eth0 Link encap:Ethernet HWaddr 00:12:3f:1f:45:0e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:214 errors:0 dropped:0 overruns:0 frame:0
TX packets:298 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:137493 (134.2 KiB) TX bytes:39076 (38.1 KiB)
Interruption:16
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)
[/code]
ifconfig -a
[code]eth0 Link encap:Ethernet HWaddr 00:12:3f:1f:45:0e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:214 errors:0 dropped:0 overruns:0 frame:0
TX packets:298 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:137493 (134.2 KiB) TX bytes:39076 (38.1 KiB)
Interruption:16
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)
wlan0 Link encap:Ethernet HWaddr 00:0b:7d:25:71:e9
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
wmaster0 Link encap:UNSPEC HWaddr 00-0B-7D-25-71-E9-6C-6F-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[/code]
iwconfig
[code]wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[/code]
Si tu n’installes pas le firmware, ça ne peut pas fonctionner.
Merci ! connaissais pas cette commande je vais la noter qq part.
Ca marche parfaitement.
encore Merci