Bonjour,
Je n’ai pas l’habitude de poster pour des cartes graphiques, je n’ai que des nvidia
Mais là… J’essaye d’installer une machine pour mes enfants (Lenny + junior) et j’ai un problème de carte :
lspci -v
01:00.0 VGA compatible controller: VIA Technologies, Inc. KM400/KN400/P4M800 [S3 UniChrome] (rev 01) (prog-if 00 [VGA controller])
Subsystem: VIA Technologies, Inc. KM400/KN400/P4M800 [S3 UniChrome]
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at f4000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at f5000000 [disabled] [size=64K]
Capabilities: <access denied>
C’est une carte intégrée…
J’ai un beau “out of range” lorsque le serveur X démarre. Je suppose que c’est un problème de fréquence qui ne colle pas avec l’écran (plat)
Mais je ne sais pas comment régler ce problème…
J’avais un problème que j’ai réglé ce matin (genre “no screen”) à coup de “Xorg -configure”
Pas de EE dans les logs de xorg…
Le xorg.conf si ça peut servir…
[code]$ cat /etc/X11/xorg.conf
Section “ServerLayout”
Identifier “X.org Configured”
Screen 0 “Screen0” 0 0
InputDevice “Mouse0” “CorePointer”
InputDevice “Keyboard0” “CoreKeyboard”
EndSection
Section “Files”
RgbPath “/etc/X11/rgb”
ModulePath “/usr/lib/xorg/modules”
FontPath “/usr/share/fonts/X11/misc”
FontPath “/usr/share/fonts/X11/cyrillic”
FontPath “/usr/share/fonts/X11/100dpi/:unscaled”
FontPath “/usr/share/fonts/X11/75dpi/:unscaled”
FontPath “/usr/share/fonts/X11/Type1”
FontPath “/usr/share/fonts/X11/100dpi”
FontPath “/usr/share/fonts/X11/75dpi”
FontPath “/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType”
EndSection
Section “Module”
Load “glx”
Load “xtrap”
Load “record”
Load “GLcore”
Load “dri”
Load “extmod”
Load “dbe”
EndSection
Section “InputDevice”
Identifier “Keyboard0”
Driver “kbd”
EndSection
Section “InputDevice”
Identifier “Mouse0”
Driver “mouse”
Option “Protocol” “auto”
Option “Device” “/dev/input/mice”
Option “ZAxisMapping” “4 5 6 7”
EndSection
Section “Monitor”
Identifier “Monitor0”
VendorName “Monitor Vendor”
ModelName “Monitor Model”
EndSection
Section “Device”
### Available Driver options are:-
### Values: : integer, : float, : “True”/“False”,
### : “String”, : " Hz/kHz/MHz"
### [arg]: arg optional
#Option “PrintVGARegs” # []
#Option “PrintTVRegs” # []
#Option “I2CScan” # []
#Option “VBEModes” # []
#Option “NoAccel” # []
#Option “AccelMethod” #
#Option “ExaNoComposite” # []
#Option “ExaScratchSize” #
#Option “SWCursor” # []
#Option “ShadowFB” # []
#Option “Rotate” # []
#Option “VideoRAM” #
#Option “ActiveDevice” # []
#Option “BusWidth” # []
#Option “Center” # []
#Option “PanelSize” # []
#Option “ForcePanel” # []
#Option “TVDotCrawl” # []
#Option “TVDeflicker” #
#Option “TVType” # []
#Option “TVOutput” # []
#Option “DisableVQ” # []
#Option “DisableIRQ” # []
#Option “EnableAGPDMA” # []
#Option “NoAGPFor2D” # []
#Option “NoXVDMA” # []
#Option “VbeSaveRestore” # []
#Option “DisableXvBWCheck” # []
#Option “MaxDRIMem” #
#Option “AGPMem” #
Identifier “Card0”
Driver “openchrome”
VendorName “Unknown Vendor”
BoardName “Unknown Board”
BusID “PCI:1:0:0”
EndSection
Section “Screen”
Identifier “Screen0”
Device “Card0”
Monitor “Monitor0”
SubSection “Display”
Viewport 0 0
Depth 1
EndSubSection
SubSection “Display”
Viewport 0 0
Depth 4
EndSubSection
SubSection “Display”
Viewport 0 0
Depth 8
EndSubSection
SubSection “Display”
Viewport 0 0
Depth 15
EndSubSection
SubSection “Display”
Viewport 0 0
Depth 16
EndSubSection
SubSection “Display”
Viewport 0 0
Depth 24
EndSubSection
EndSection[/code]
Merci d’avance pour vos suggestions.
PS : Je n’ai pour l’instant qu’un accès SSH à la machine…