Bonjour, peu après l’upgrade à Debian 9 le boot est devenu très lent. D’abord écran noir pendant plusieurs minutes, puis le logo ASUS pendant plusieurs minutes, puis le boot pendant lequel les messages suivants apparaissent :
nouveau - pointer to TMDS table invalid
nouveau - pointer to flat panel table invalid
Merci
C’est bizarre, car ça, c’est hardware, debian ne démarre qu’aprés le logo asus.
Ca recommence au reboot suivant ?
Ca semble indiquer un soucis avec ton pilote de carte graphique.
Tu sais quel pilote tu utilisais ?
~$ lspci | grep VGA
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
Donc pas immédiatement après ?
Tu veux dire que c’est l’initialisation du firmware (BIOS, UEFI) de la machine ?
Pour la petite histoire, j’ai une carte mère Intel dont l’initialisation peut être extrêmement lente en fonction des supports de stockages connectés (disques internes, lecteur optique surtout quand un CD ou DVD est présent, supports USB).
“nouveau” est le pilote libre des GPU Nvidia. Or lspci affiche un GPU Intel. Il doit y avoir un GPU secondaire Nvidia qui n’est pas identifié “VGA” mais “3D controller” ou quelque chose du genre. Technologie Optimus ?
$ lspci
00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09)
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
00:16.0 Communication controller: Intel Corporation 7 Series/C216 Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C216 Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C216 Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C216 Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C216 Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C216 Chipset Family SMBus Controller (rev 04)
01:00.0 3D controller: NVIDIA Corporation GK208M [GeForce GT 740M] (rev a1)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 07)
03:00.0 Network controller: Qualcomm Atheros AR9485 Wireless Network Adapter (rev 01)
C’est ça.
Si tu veux passer sur le pilote propriétaire pour savoir s’il fonctionne mieux, voici la démarche:
https://wiki.debian.org/fr/NvidiaGraphicsDrivers#Version_375.66
J’ai installé
# apt install linux-headers-$(uname -r|sed 's/[^-]*-[^-]*-//') nvidia-driver
–> tjrs démarrage lent … et en plus impossible de démarrer Evolution -->
# apt autoremove linux-headers-$(uname -r|sed 's/[^-]*-[^-]*-//') nvidia-driver
Retour au problème du démarrage : je viens de chronométrer avec précision : en fait la lenteur est avant le boot Debian : démarrage --> 2min d’écran noir --> 1min de logo asus --> puis le boot Debian …
C’est ce que je disais, l’install de debian me semble une coïncidence, et ça viens du hard:
le logo asus arrive avant le boot du système.
Regardes si les réglages bios n’ont pas sauté ?
sinon, pour connaitre le chronométrage de ton boot sur la partie ou debian prend la main, tu regardes dmesg juste aprés ton boot, il y a un timestamp des messages en secondes depuis le boot.
Oui, à mon avis cela a été causé suite à une mise à jour (je les fais environ tous les quinze jours). Mais quoi … ?
# dmesg
(...)
[ 19.492697] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
[ 34.044239] usblp0: removed
[ 34.120737] usb 2-1.6: reset full-speed USB device number 4 using ehci-pci
[ 39.408845] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0224
[ 59.295626] evolution[1500]: segfault at 0 ip 00007fec2451a1d5 sp 00007ffc19413790 error 4 in libc-2.24.so[7fec244e3000+195000]
[ 836.045568] evolution[1766]: segfault at 0 ip 00007f678586d1d5 sp 00007fff95f0ef90 error 4 in libc-2.24.so[7f6785836000+195000]
[ 1238.292379] systemd[1]: apt-daily.timer: Adding 1h 17min 30.650080s random time.
[ 1238.292549] systemd[1]: apt-daily-upgrade.timer: Adding 36min 32.587628s random time.
[ 1238.292632] systemd[1]: anacron.timer: Adding 3min 23.338789s random time.
[ 1270.009489] device-mapper: uevent: version 1.0.3
[ 1270.009640] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 1274.734583] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 1274.757041] JFS: nTxBlock = 8192, nTxLock = 65536
[ 1274.810781] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[ 1274.856605] QNX4 filesystem 0.2.3 registered.
[ 1274.956926] raid6: sse2x1 gen() 7633 MB/s
[ 1275.024930] raid6: sse2x1 xor() 6880 MB/s
[ 1275.092938] raid6: sse2x2 gen() 11587 MB/s
[ 1275.160941] raid6: sse2x2 xor() 8225 MB/s
[ 1275.228947] raid6: sse2x4 gen() 13476 MB/s
[ 1275.296948] raid6: sse2x4 xor() 9951 MB/s
[ 1275.296949] raid6: using algorithm sse2x4 gen() 13476 MB/s
[ 1275.296949] raid6: .... xor() 9951 MB/s, rmw enabled
[ 1275.296950] raid6: using ssse3x2 recovery algorithm
[ 1275.315659] xor: automatically using best checksumming function avx
[ 1275.347551] Btrfs loaded, crc32c=crc32c-intel
[ 1275.360990] fuse init (API version 7.26)
[ 2575.695303] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2575.695305] Bluetooth: BNEP filters: protocol multicast
[ 2575.695308] Bluetooth: BNEP socket layer initialized
[ 3084.398509] usb 3-2: new high-speed USB device number 3 using xhci_hcd
[ 3084.539204] usb 3-2: New USB device found, idVendor=0781, idProduct=5572
[ 3084.539208] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3084.539210] usb 3-2: Product: Cruzer Switch
[ 3084.539212] usb 3-2: Manufacturer: SanDisk
[ 3084.539214] usb 3-2: SerialNumber: 4C530012520401122125
[ 3084.539704] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 3084.540152] scsi host7: usb-storage 3-2:1.0
[ 3085.563770] scsi 7:0:0:0: Direct-Access SanDisk Cruzer Switch 1.27 PQ: 0 ANSI: 6
[ 3085.564737] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 3085.565924] sd 7:0:0:0: [sdb] 122107136 512-byte logical blocks: (62.5 GB/58.2 GiB)
[ 3085.567602] sd 7:0:0:0: [sdb] Write Protect is off
[ 3085.567607] sd 7:0:0:0: [sdb] Mode Sense: 43 00 00 00
[ 3085.567911] sd 7:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3085.582879] sdb: sdb1
[ 3085.585358] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 3085.811757] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[21557.312425] perf: interrupt took too long (2512 > 2500), lowering kernel.perf_event_max_sample_rate to 79500
[27740.470901] perf: interrupt took too long (3147 > 3140), lowering kernel.perf_event_max_sample_rate to 63500
Donc le timing part en cacahouète juste après des infos sur “printer” et “Evolution”. Or le problème de lenteur au démarrage fut concomitant avec l’apparition d’ un prob de l’impression : je dois éteindre puis rallumer manuellement l’imprimante (brother dcp-375cw) pour pouvoir imprimer …
Je viens de remarquer que quand je retire le câble usb de l’imprimante, le problème de démarrage lent disparaît …
personnellement ce qui me ferait peur c’est plutôt ça, comme disait Mickey,
[ 59.295626] evolution[1500]: segfault at 0 ip 00007fec2451a1d5 sp 00007ffc19413790 error 4 in libc-2.24.so[7fec244e3000+195000]
[ 836.045568] evolution[1766]: segfault at 0 ip 00007f678586d1d5 sp 00007fff95f0ef90 error 4 in libc-2.24.so[7f6785836000+195000]
836-59=777 secondes perdues
puis
1238-836= 402 secondes perdues
peut etre essayer
apt install --reinstall evolution
Tous ces messages ne me semblent pas faire partie du démarrage. Evolution est une application lancée par l’utilisateur ou à l’ouverture d’une session utilisateur, pas au démarrage du système.
Tu l’as écrit toi-même : la lenteur se produit avant le boot Debian, donc inutile de la chercher dans les dates des messages du noyau.
Tiens donc…
Et evolution, il plante toujours si l’imprimante est débranchée ?
C’est juste un plantage d’une application qui peut être dû à un bug de celle-ci.
Avant d’essayer de réinstaller des trucs et des machins, il vaudrait mieux tester l’application sans l’imprimante d’une part et dans la session d’un autre utilisateur d’autre part pour vérifier que le plantage est indépendant du profil utilisateur et des ses données.
il existe evolution-calendar-factory, evolution-addressbook-factory qui sont lancés au démarrage sans action de l’utilisateur
Pour le voir, il suffit de faire
ps -edf | grep evolut
root@debian:/# journalctl -xb | grep evol
févr. 18 13:43:41 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Activating via systemd: service name='org.gnome.evolution.dataserver.Sources5' unit='evolution-source-registry.service' requested by ':1.19' (uid=1001 pid=7745 comm="/usr/lib/gnome-shell/gnome-shell-calendar-server ")
févr. 18 13:43:42 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Activating service name='org.gnome.OnlineAccounts' requested by ':1.20' (uid=1001 pid=7749 comm="/usr/lib/evolution/evolution-source-registry ")
févr. 18 13:43:44 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Successfully activated service 'org.gnome.evolution.dataserver.Sources5'
févr. 18 13:43:50 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Activating via systemd: service name='org.gnome.evolution.dataserver.Calendar7' unit='evolution-calendar-factory.service' requested by ':1.19' (uid=1001 pid=7745 comm="/usr/lib/gnome-shell/gnome-shell-calendar-server ")
févr. 18 13:43:58 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Successfully activated service 'org.gnome.evolution.dataserver.Calendar7'
févr. 18 13:43:58 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Activating service name='ca.desrt.dconf' requested by ':1.58' (uid=1001 pid=8016 comm="/usr/lib/evolution/evolution-calendar-factory-subp")
févr. 18 13:43:58 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Activating via systemd: service name='org.gnome.evolution.dataserver.AddressBook9' unit='evolution-addressbook-factory.service' requested by ':1.58' (uid=1001 pid=8016 comm="/usr/lib/evolution/evolution-calendar-factory-subp")
févr. 18 13:43:59 debian dbus-daemon[7529]: [session uid=1001 pid=7529] Successfully activated service 'org.gnome.evolution.dataserver.AddressBook9'
févr. 18 14:43:43 debian evolution-sourc[7749]: secret_service_search_sync: must specify at least one attribute to match
root@debian:/#
Plutôt à l’ouverture de session, non ?
Exact.
On ne peut pas désinstaller Evolution , ça casse gnome-shell
Si on n’utilise pas les fonctions d’Evolution, on peut les masquer pour s’en affranchir:
debian:~$ systemctl --user mask evolution-calendar-factory.service evolution-source-registry.service evolution-addressbook-factory.service
Je n’ai plus le problème avec Evolution, qui était apparu suite à l’installation de nvidia-driver (maintenant supprimé). Mais le problème originel subsiste : si le câble usb de l’imprimante Brother dcp-375cw est branché le démarrage du shell est ralenti. Je viens de réinstaller Debian et les drivers HP, mais maintenant c’est pire : impossible d’imprimer, alors qu’avant j’y arrivais encore en éteignant puis rallumant l’imprimante.
E [18/Feb/2018:19:04:30 +0100] [Client 14] Empty Basic password.
E [18/Feb/2018:22:24:55 +0100] [cups-deviced] PID 8761 (gutenprint52+usb) stopped with status 1!
E [18/Feb/2018:22:31:37 +0100] [Job 1] Unable to send data to printer.
J’ai réinstallé Debian 9 et les drivers de l’imprimante. Mais le problème demeure :
# dmesg (...) [ 2.297620] usb 2-1.6: New USB device found, idVendor=04f9, idProduct=0224 [ 2.297622] usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.297624] usb 2-1.6: Product: DCP-375CW [ 2.297626] usb 2-1.6: Manufacturer: Brother [ 2.297628] usb 2-1.6: SerialNumber: BROE9F197221 (...) [ 4.459726] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ 4.864099] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 4.945401] lp: driver loaded but no devices found [ 5.057058] systemd-journald[275]: Received request to flush runtime journal from PID 1 (...) [ 6.111053] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20160831/utaddress-247) [ 6.111057] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 6.111059] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20160831/utaddress-247) [ 6.111062] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x000000000000055F (\_SB.PCI0.PEG0.PEGP.GPIO) (20160831/utaddress-247) [ 6.111064] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 6.111064] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20160831/utaddress-247) [ 6.111066] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000055F (\_SB.PCI0.PEG0.PEGP.GPIO) (20160831/utaddress-247) [ 6.111068] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 6.111068] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20160831/utaddress-247) [ 6.111070] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000055F (\_SB.PCI0.PEG0.PEGP.GPIO) (20160831/utaddress-247) [ 6.111072] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 6.111072] lpc_ich: Resource conflict(s) found affecting gpio_ich [ 6.295047] [Firmware Bug]: battery: (dis)charge rate invalid. (...) [ 6.552447] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 6.581073] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS (...) [ 6.923358] MXM: GUID detected in BIOS [ 6.923420] ACPI Warning: \_SB.PCI0.GFX0._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 6.923439] ACPI: \_SB_.PCI0.GFX0: failed to evaluate _DSM [ 6.923526] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 6.923616] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 6.923868] pci 0000:01:00.0: optimus capabilities: enabled, status dynamic power, hda bios codec supported [ 6.923871] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG0.PEGP handle [ 6.923897] nouveau 0000:01:00.0: enabling device (0006 -> 0007) [ 7.113872] usb 1-1.3: firmware: failed to load ar3k/AthrBT_0x01020200.dfu (-2) [ 7.113875] usb 1-1.3: Direct firmware load for ar3k/AthrBT_0x01020200.dfu failed with error -2 [ 7.113878] Bluetooth: Loading patch file failed [ 7.113885] ath3k: probe of 1-1.3:1.0 failed with error -2 (...) [ 7.503070] nouveau 0000:01:00.0: priv: HUB0: 085014 ffffffff (1970820b) [ 7.503115] nouveau 0000:01:00.0: priv: GPC0: 4188ac 00000001 (1c70822e) [ 7.503157] nouveau 0000:01:00.0: priv: HUB0: 10ecc0 ffffffff (1f70822c) [ 7.557517] vga_switcheroo: enabled [ 7.557614] [TTM] Zone kernel: Available graphics memory: 4027010 kiB [ 7.557615] [TTM] Zone dma32: Available graphics memory: 2097152 kiB [ 7.557615] [TTM] Initializing pool allocator [ 7.557618] [TTM] Initializing DMA pool allocator [ 7.557635] nouveau 0000:01:00.0: DRM: VRAM: 2048 MiB [ 7.557636] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB [ 7.557639] nouveau 0000:01:00.0: DRM: Pointer to TMDS table invalid [ 7.557640] nouveau 0000:01:00.0: DRM: DCB version 4.0 [ 7.557641] nouveau 0000:01:00.0: DRM: Pointer to flat panel table invalid (...) [ 7.988079] USB Video Class driver (1.1.1) [ 8.772709] Adding 8262652k swap on /dev/sda3. Priority:-1 extents:1 across:8262652k FS [ 13.039568] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 13.040064] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM [ 13.040072] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 13.040398] nouveau 0000:01:00.0: DRM: evicting buffers... [ 13.040401] nouveau 0000:01:00.0: DRM: waiting for kernel channels to go idle... [ 13.040423] nouveau 0000:01:00.0: DRM: suspending client object trees... [ 13.041649] nouveau 0000:01:00.0: DRM: suspending kernel object tree... [ 13.554894] usblp: can't set desired altsetting 0 on interface 0 [ 13.555018] usbcore: registered new interface driver usblp [ 14.794097] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready [ 14.794364] r8169 0000:02:00.0: firmware: failed to load rtl_nic/rtl8168e-3.fw (-2) [ 14.794428] r8169 0000:02:00.0: Direct firmware load for rtl_nic/rtl8168e-3.fw failed with error -2 [ 14.794432] r8169 0000:02:00.0 enp2s0: unable to load firmware patch rtl_nic/rtl8168e-3.fw (-2) [ 14.813791] r8169 0000:02:00.0 enp2s0: link down [ 14.813792] r8169 0000:02:00.0 enp2s0: link down [ 14.813861] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready [ 14.818710] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready [ 14.833512] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready [ 14.858673] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready [ 14.963823] nouveau 0000:01:00.0: DRM: resuming kernel object tree... [ 15.006670] nouveau 0000:01:00.0: priv: HUB0: 085014 ffffffff (1a70820b) [ 15.006731] nouveau 0000:01:00.0: priv: GPC0: 4188ac 00000001 (1d70822e) [ 15.037792] nouveau 0000:01:00.0: priv: HUB0: 10ecc0 ffffffff (1970822c) [ 15.058113] nouveau 0000:01:00.0: DRM: resuming client object trees... [ 15.774367] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready [ 16.532122] r8169 0000:02:00.0 enp2s0: link up [ 16.532138] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready [ 26.864612] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 26.865189] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM [ 26.865199] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 26.865581] nouveau 0000:01:00.0: DRM: evicting buffers... [ 26.881663] nouveau 0000:01:00.0: DRM: waiting for kernel channels to go idle... [ 26.881684] nouveau 0000:01:00.0: DRM: suspending client object trees... [ 26.882983] nouveau 0000:01:00.0: DRM: suspending kernel object tree... [ 34.421240] nouveau 0000:01:00.0: DRM: resuming kernel object tree... [ 34.464083] nouveau 0000:01:00.0: priv: HUB0: 085014 ffffffff (1a70820b) [ 34.464093] nouveau 0000:01:00.0: priv: GPC0: 4188ac 00000001 (1d70822e) [ 34.509114] nouveau 0000:01:00.0: priv: HUB0: 10ecc0 ffffffff (1970822c) [ 34.590015] nouveau 0000:01:00.0: DRM: resuming client object trees... [ 35.149171] usb 2-1.6: reset full-speed USB device number 4 using ehci-pci [ 39.921587] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 39.922053] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM [ 39.922060] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 39.922435] nouveau 0000:01:00.0: DRM: evicting buffers... [ 39.922438] nouveau 0000:01:00.0: DRM: waiting for kernel channels to go idle... [ 39.922466] nouveau 0000:01:00.0: DRM: suspending client object trees... [ 39.924124] nouveau 0000:01:00.0: DRM: suspending kernel object tree... [ 40.375981] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 105.447617] usb 2-1.6: USB disconnect, device number 4 [ 123.623515] usb 2-1.6: new full-speed USB device number 5 using ehci-pci [ 123.734465] usb 2-1.6: New USB device found, idVendor=04f9, idProduct=0224 [ 123.734470] usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 123.734472] usb 2-1.6: Product: DCP-375CW [ 123.734474] usb 2-1.6: Manufacturer: Brother [ 123.734475] usb 2-1.6: SerialNumber: BROE9F197221 [ 123.736236] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0224 [ 123.736506] usb-storage 2-1.6:1.2: USB Mass Storage device detected [ 123.736669] scsi host7: usb-storage 2-1.6:1.2 [ 124.774833] scsi 7:0:0:0: Direct-Access Brother DCP-375CW 1.00 PQ: 0 ANSI: 2 [ 124.775540] sd 7:0:0:0: Attached scsi generic sg3 type 0 [ 124.835074] sd 7:0:0:0: [sdc] Attached SCSI removable disk [ 125.811516] usblp0: removed [ 126.065102] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0224 [ 126.083617] usblp0: removed [ 128.092486] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0224 [ 230.205327] nouveau 0000:01:00.0: DRM: resuming kernel object tree... [ 230.248172] nouveau 0000:01:00.0: priv: HUB0: 085014 ffffffff (1a70820b) [ 230.248182] nouveau 0000:01:00.0: priv: GPC0: 4188ac 00000001 (1d70822e) [ 230.291191] nouveau 0000:01:00.0: priv: HUB0: 10ecc0 ffffffff (1970822c) [ 230.370137] nouveau 0000:01:00.0: DRM: resuming client object trees... [ 235.801431] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 235.801845] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM [ 235.801850] ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20160831/nsarguments-95) [ 235.802094] nouveau 0000:01:00.0: DRM: evicting buffers... [ 235.802097] nouveau 0000:01:00.0: DRM: waiting for kernel channels to go idle... [ 235.802118] nouveau 0000:01:00.0: DRM: suspending client object trees... [ 235.803522] nouveau 0000:01:00.0: DRM: suspending kernel object tree... [ 357.881583] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready [ 672.090106] usblp0: removed [ 672.853757] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready [ 674.093178] usblp 2-1.6:1.0: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0224
Comment interpréter ces infos ?
Salut
Brother fourni le driver compatible Linux pour cette imprimante:
As tu essayé?
Oui ce sont bien ceux-là que j’avais installé :
dpkg -l | grep Brother
ii dcp375cwcupswrapper:i386 1.1.3-1 i386 Brother CUPS Inkjet Printer Definitions
ii dcp375cwlpr:i386 1.1.3-1 i386 Brother lpr Inkjet Printer Definitions
ii printer-driver-brlaser 3-5+b1 amd64 printer driver for (some) Brother laser printers
ii printer-driver-ptouch 1.4.2-2+b1 amd64 printer driver Brother P-touch label printers
Mais toujours ce problème. Quand je lance une impression CUPS affiche "“Waiting for printer to become available.” --> si j’éteins et rallume l’imprimante alors ça fonctionne …