Bonjour,
Je viens de réinstaller mon portable en utilisant l’image contenant les firmware (firmware-10.1.0-amd64-netinst). J’ai aussi installé KDE.
Le portable possède un carte réseau ethernet et une wifi.
La carte réseau ethernet est bien reconnue et fonctionne mais elle porte un nom qui ne correspond, il me semble, ni aux anciennes normes, ni aux nouvelles
ip a donne :
eno1
Mais ce qui m’embête le plus, c’est que je n’arrive pas à configurer la carte wifi. J’ai suivi le tuto http://debian-facile.org/doc:materiel:wifi:detecter, sans succès. J’ai installé le firmware firmware-brcm80211 mais ca ne marche toujours pas.
Voici les infos utilisées par le tuto.
lspci -nnd ::0280 :
08:00.0 Network controller [0280]: Broadcom Limited BCM43142 802.11b/g/n [14e4:4365] (rev 01)
lsusb :
Bus 003 Device 002: ID 8087:8001 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 0a5c:216d Broadcom Corp. BCM43142A0 Bluetooth 4.0
Bus 001 Device 003: ID 04f2:b50d Chicony Electronics Co., Ltd
Bus 001 Device 002: ID 046d:c52f Logitech, Inc. Unifying Receiver
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
lspci -nnkd ::0280 :
08:00.0 Network controller [0280]: Broadcom Limited BCM43142 802.11b/g/n [14e4:4365] (rev 01)
Subsystem: Hewlett-Packard Company BCM43142 802.11b/g/n [103c:804a]
Kernel modules: bcma, wl
ip a :
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether b0:5a:da:d7:ab:09 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.110/24 brd 192.168.1.255 scope global dynamic noprefixroute eno1
valid_lft 83613sec preferred_lft 83613sec
inet6 fe80::c369:b5ac:9c72:655c/64 scope link noprefixroute
valid_lft forever preferred_lft forever
dmesg | grep firmware :
[ 0.242195] Spectre V2 : Enabling Restricted Speculation for firmware calls
[ 3.530866] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_mc.bin
[ 3.533994] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_pfp.bin
[ 3.534015] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_me.bin
[ 3.534031] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_ce.bin
[ 3.534047] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_rlc.bin
[ 3.534132] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_mec.bin
[ 3.534910] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_sdma.bin
[ 3.534924] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_sdma1.bin
[ 3.535170] amdgpu 0000:0a:00.0: firmware: direct-loading firmware amdgpu/topaz_k_smc.bin
[ 5.596950] bluetooth hci0: firmware: direct-loading firmware brcm/BCM43142A0-0a5c-216d.hcd
[ 6.969204] r8169 0000:09:00.0: firmware: direct-loading firmware rtl_nic/rtl8107e-2.fw
Qu’ai-je loupé ? Je ne comprends pas .
Merci de votre aide