Debian live box et wifi résolu

Support Debian
#1

Bonjour à tous
j’espère que je pourrais avoir une aide, car voilà 2 jours que je galère.

j’essaie désespérément de connecter un pc à la live box inventel à l’aide d’une clé wifi :angry: :angry:

2 modéles essayés :
un sagem xg 760n et un d-link dwl-g122 h/w
le sagem fonctionne sous XP, sous UBUNTU j’ai la connection avec la live et pas le NET

un lsusb me donne cela : (ici le modele sagem)

[code]bene:/home/benedicte# lsusb

Bus 004 Device 003: ID 07c4:0601 Datafab Systems, Inc.
Bus 004 Device 002: ID 079b:0062 Sagem XG-76NA 802.11bg
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[/code]

et un iwconfig cela :

[code]bene:/home/benedicte# lsusb
Bus 004 Device 003: ID 07c4:0601 Datafab Systems, Inc.
Bus 004 Device 002: ID 079b:0062 Sagem XG-76NA 802.11bg
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
bene:/home/benedicte# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wmaster0 no wireless extensions.

wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[/code]

avec wicd network manager je ne trouve pas de liaison sans fil..

voilà, j’en suis là

merci de votre aide… :smiley: :smiley:

#2

t’a activé me mode association de la livebox ?

#3

bonjour,

…oui…

mais j’émets un doute, on associe la live avant de faire les reglages ?

1 - je mets la clé
2 - j'associe la live
3 - je connecte le pc a la live en entrant le ssid et la clé wep...(jamais de problèmes avec d'autres ordis pour le choix du WEP)

c'est dans l'ordre
#4

Ca doit être bon, activer le mode association = ouvrir la porte pendant quelques secondes pour autoriser un nouveau pc a se connecter.

#5

Perso. l’asso de ma box a tjs été foireuse (via le petit bouton rouge).
Je désactive la securité via le panel de la box le temps de récupérer l’adresse MAC et réactive ensuite manuellement la sécurité.
L’association via le bouton a souvent été très aléatoire dans mon cas…
(c’est une sagem)

Pour la config. préfère WICD, ça tourne très très bien.

++

Cyrille

#6

Et que donne iwlist scanning ?

As tu vu ça : wiki.debian.org/zd1211rw

Et que donne dmesg ?

++
Cyrille

#7

1-

[code]bene:/home/benedicte# iwlist scanning
lo Interface doesn’t support scanning.

eth0 Interface doesn’t support scanning.

wmaster0 Interface doesn’t support scanning.

wlan0 Interface doesn’t support scanning : Network is down

[/code]

-2

[code]bene:/home/benedicte# dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-24) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Mon Jun 21 05:58:44 UTC 2010
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000fef0000 (usable)
[ 0.000000] BIOS-e820: 000000000fef0000 - 000000000fef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000000fef3000 - 000000000ff00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 254MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 65264) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 65264
[ 0.000000] HighMem 65264 -> 65264
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65264
[ 0.000000] On node 0 totalpages: 65264
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 478 pages used for memmap
[ 0.000000] Normal zone: 60690 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.2 present.
[ 0.000000] ACPI: RSDP 000F6F80, 0014 (r0 000000)
[ 0.000000] ACPI: RSDT 0FEF3000, 0028 (r1 000000 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: FACP 0FEF3040, 0074 (r1 000000 AWRDACPI 42302E31 AWRD 0)
[ 0.000000] ACPI: DSDT 0FEF30C0, 2D6C (r1 000000 AWRDACPI 1000 MSFT 100000C)
[ 0.000000] ACPI: FACS 0FEF0000, 0040
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] Allocating PCI resources starting at 10000000 (gap: 0ff00000:efc00000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] SMP: Allowing 0 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64754
[ 0.000000] Kernel command line: root=/dev/hda1 ro quiet
[ 0.000000] Local APIC disabled by BIOS – you can enable it with “lapic”
[ 0.000000] mapped APIC to ffffb000 (0120c000)
[ 0.000000] Enabling fast FPU save and restore… done.
[ 0.000000] Enabling unmasked SIMD FPU exception support… done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 634.798 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.004000] Memory: 248900k/261056k available (1771k kernel code, 11628k reserved, 750k data, 244k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xcfef0000 ( 254 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02badcd - 0xc0376620 ( 750 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02badcd (1771 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode…Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084502] Calibrating delay using timer specific routine… 1271.57 BogoMIPS (lpj=2543142)
[ 0.084657] Security Framework initialized
[ 0.084688] SELinux: Disabled at boot.
[ 0.084703] Capability LSM initialized
[ 0.084768] Mount-cache hash table entries: 512
[ 0.085387] Initializing cgroup subsys ns
[ 0.085407] Initializing cgroup subsys cpuacct
[ 0.085417] Initializing cgroup subsys devices
[ 0.085512] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 0.085525] CPU: L2 cache: 128K
[ 0.085545] Intel machine check architecture supported.
[ 0.085558] Intel machine check reporting enabled on CPU#0.
[ 0.085620] Checking ‘hlt’ instruction… OK.
[ 0.101114] SMP alternatives: switching to UP code
[ 0.115649] Freeing SMP alternatives: 16k freed
[ 0.115677] ACPI: Core revision 20080321
[ 0.127199] ACPI: setting ELCR to 0200 (from 0a28)
[ 0.132008] weird, boot CPU (#0) not listedby the BIOS.
[ 0.132008] SMP motherboard not detected.
[ 0.132008] Local APIC not detected. Using dummy APIC emulation.
[ 0.132008] SMP disabled
[ 0.132008] Brought up 1 CPUs
[ 0.132008] Total of 1 processors activated (1271.57 BogoMIPS).
[ 0.132008] CPU0 attaching sched-domain:
[ 0.132008] domain 0: span 0
[ 0.132008] groups: 0
[ 0.132008] net_namespace: 660 bytes
[ 0.132008] Booting paravirtualized kernel on bare hardware
[ 0.132008] NET: Registered protocol family 16
[ 0.132723] ACPI: bus type pci registered
[ 0.159685] PCI: PCI BIOS revision 2.10 entry at 0xfb0f0, last bus=1
[ 0.159701] PCI: Using configuration type 1 for base access
[ 0.159736] Setting up standard PCI resources
[ 0.166655] ACPI: EC: Look up EC in DSDT
[ 0.178933] ACPI: Interpreter enabled
[ 0.178958] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.179030] ACPI: Using PIC for interrupt routing
[ 0.200980] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.201637] pci 0000:00:1f.0: quirk: region 4000-407f claimed by ICH4 ACPI/GPIO/TCO
[ 0.201656] pci 0000:00:1f.0: quirk: region 4080-40bf claimed by ICH4 GPIO
[ 0.202472] PCI: Transparent bridge - 0000:00:1e.0
[ 0.202566] ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PRT]
[ 0.203036] ACPI: PCI Interrupt Routing Table [_SB.PCI0.HUB0._PRT]
[ 0.210082] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.210455] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.210796] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
[ 0.211135] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.211963] Linux Plug and Play Support v0.97 © Adam Belay
[ 0.212262] pnp: PnP ACPI init
[ 0.212346] ACPI: bus type pnp registered
[ 0.230028] pnp: PnP ACPI: found 15 devices
[ 0.230045] ACPI: ACPI bus type pnp unregistered
[ 0.230061] PnPBIOS: Disabled by ACPI PNP
[ 0.231841] PCI: Using ACPI for IRQ routing
[ 0.232939] system 00:00: iomem range 0xca000-0xcffff has been reserved
[ 0.232960] system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.232971] system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.232982] system 00:00: iomem range 0xfc000-0xfffff could not be reserved
[ 0.232994] system 00:00: iomem range 0xfef0000-0xfefffff could not be reserved
[ 0.233005] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.233017] system 00:00: iomem range 0x100000-0xfeeffff could not be reserved
[ 0.233030] system 00:00: iomem range 0xffb00000-0xffb7ffff could not be reserved
[ 0.233042] system 00:00: iomem range 0xfff00000-0xffffffff could not be reserved
[ 0.233053] system 00:00: iomem range 0xe0000-0xeffff has been reserved
[ 0.233092] system 00:03: ioport range 0x290-0x297 has been reserved
[ 0.233103] system 00:03: ioport range 0x3f0-0x3f1 has been reserved
[ 0.233114] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[ 0.233125] system 00:03: ioport range 0x800-0x805 has been reserved
[ 0.265912] PCI: Bridge: 0000:00:1e.0
[ 0.265930] IO window: b000-cfff
[ 0.265944] MEM window: 0xd4000000-0xd40fffff
[ 0.265955] PREFETCH window: disabled.
[ 0.265987] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.266112] NET: Registered protocol family 2
[ 0.266553] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.267440] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.267752] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.268207] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.268225] TCP reno registered
[ 0.268872] NET: Registered protocol family 1
[ 0.269373] checking if image is initramfs…<7>Switched to high resolution mode on CPU 0
[ 1.171654] it is
[ 2.343985] Freeing initrd memory: 6071k freed
[ 2.347134] audit: initializing netlink socket (disabled)
[ 2.347197] type=2000 audit(1280106869.344:1): initialized
[ 2.347685] Total HugeTLB memory allocated, 0
[ 2.348139] VFS: Disk quotas dquot_6.5.1
[ 2.348271] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.348448] msgmni has been set to 498
[ 2.349142] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.349166] io scheduler noop registered
[ 2.349174] io scheduler anticipatory registered
[ 2.349181] io scheduler deadline registered
[ 2.349253] io scheduler cfq registered (default)
[ 2.349309] pci 0000:00:01.0: Boot video device
[ 2.351426] isapnp: Scanning for PnP cards…
[ 2.706199] isapnp: No Plug & Play device found
[ 2.724000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.724600] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.726762] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.736857] brd: module loaded
[ 2.737464] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.740912] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.740939] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.741871] mice: PS/2 mouse device common for all mice
[ 2.742656] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.742895] rtc0: alarms up to one month
[ 2.743150] cpuidle: using governor ladder
[ 2.743163] cpuidle: using governor menu
[ 2.743188] No iBFT detected.
[ 2.745179] TCP cubic registered
[ 2.745193] NET: Registered protocol family 17
[ 2.745220] Using IPI No-Shortcut mode
[ 2.746126] registered taskstats version 1
[ 2.747000] rtc_cmos 00:05: setting system clock to 2010-07-26 01:14:31 UTC (1280106871)
[ 2.748045] Freeing unused kernel memory: 244k freed
[ 2.770538] input: AT Translated Set 2 keyboard as /class/input/input0
[ 3.169832] ACPI: PNP0C0B:00 is registered as cooling_device0
[ 3.169861] ACPI: Fan [FAN] (on)
[ 3.200598] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 3.200876] ACPI: ACPI0007:00 is registered as cooling_device1
[ 3.200899] ACPI: Processor [CPU0] (supports 2 throttling states)
[ 3.210285] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 3.210863] ACPI: Thermal Zone [THRM] (31 C)
[ 4.956697] No dock devices found.
[ 5.490981] SCSI subsystem initialized
[ 5.619299] usbcore: registered new interface driver usbfs
[ 5.619416] usbcore: registered new interface driver hub
[ 5.619628] usbcore: registered new device driver usb
[ 6.046675] USB Universal Host Controller Interface driver v3.0
[ 6.047468] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
[ 6.047484] PCI: setting IRQ 5 as level-triggered
[ 6.047494] ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[ 6.047533] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 6.047546] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 6.047973] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
[ 6.048127] uhci_hcd 0000:00:1f.2: irq 5, io base 0x0000d000
[ 6.048549] usb usb1: configuration #1 chosen from 1 choice
[ 6.048668] hub 1-0:1.0: USB hub found
[ 6.048718] hub 1-0:1.0: 2 ports detected
[ 6.049001] libata version 3.00 loaded.
[ 6.152641] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.152660] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.152671] usb usb1: Product: UHCI Host Controller
[ 6.152679] usb usb1: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 6.152687] usb usb1: SerialNumber: 0000:00:1f.2
[ 6.153431] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3
[ 6.153447] PCI: setting IRQ 3 as level-triggered
[ 6.153456] ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKB] -> GSI 3 (level, low) -> IRQ 3
[ 6.153494] uhci_hcd 0000:01:05.0: UHCI Host Controller
[ 6.153654] uhci_hcd 0000:01:05.0: new USB bus registered, assigned bus number 2
[ 6.153716] uhci_hcd 0000:01:05.0: irq 3, io base 0x0000b400
[ 6.154117] usb usb2: configuration #1 chosen from 1 choice
[ 6.154240] hub 2-0:1.0: USB hub found
[ 6.154291] hub 2-0:1.0: 2 ports detected
[ 6.256640] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.256659] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.256670] usb usb2: Product: UHCI Host Controller
[ 6.256678] usb usb2: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 6.256686] usb usb2: SerialNumber: 0000:01:05.0
[ 6.257591] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 6.257611] PCI: setting IRQ 11 as level-triggered
[ 6.257621] ACPI: PCI Interrupt 0000:01:05.1[B] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 6.257662] uhci_hcd 0000:01:05.1: UHCI Host Controller
[ 6.257832] uhci_hcd 0000:01:05.1: new USB bus registered, assigned bus number 3
[ 6.257896] uhci_hcd 0000:01:05.1: irq 11, io base 0x0000b800
[ 6.258344] usb usb3: configuration #1 chosen from 1 choice
[ 6.258472] hub 3-0:1.0: USB hub found
[ 6.258517] hub 3-0:1.0: 2 ports detected
[ 6.360547] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.360567] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.360577] usb usb3: Product: UHCI Host Controller
[ 6.360586] usb usb3: Manufacturer: Linux 2.6.26-2-686 uhci_hcd
[ 6.360594] usb usb3: SerialNumber: 0000:01:05.1
[ 6.384584] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 6.384608] via-rhine: Broken BIOS detected, avoid_D3 enabled.
[ 6.385332] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 6.385348] ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 6.391718] eth0: VIA Rhine III at 0x1b000, 00:40:f4:8b:ea:7d, IRQ 11.
[ 6.395123] eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
[ 6.507300] Uniform Multi-Platform E-IDE driver
[ 6.507324] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 6.545601] ACPI: PCI Interrupt 0000:01:05.2[C] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[ 6.545669] ehci_hcd 0000:01:05.2: EHCI Host Controller
[ 6.545808] ehci_hcd 0000:01:05.2: new USB bus registered, assigned bus number 4
[ 6.545961] ehci_hcd 0000:01:05.2: irq 5, io mem 0xd4001000
[ 6.636207] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 6.648150] ehci_hcd 0000:01:05.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 6.648515] usb usb4: configuration #1 chosen from 1 choice
[ 6.648652] hub 4-0:1.0: USB hub found
[ 6.648699] hub 4-0:1.0: 4 ports detected
[ 6.704246] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 6.752586] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.752604] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.752615] usb usb4: Product: EHCI Host Controller
[ 6.752623] usb usb4: Manufacturer: Linux 2.6.26-2-686 ehci_hcd
[ 6.752632] usb usb4: SerialNumber: 0000:01:05.2
[ 6.763499] ICH0: IDE controller (0x8086:0x2421 rev 0x01) at PCI slot 0000:00:1f.1
[ 6.763554] ICH0: not 100% native mode: will probe irqs later
[ 6.763590] ide0: BM-DMA at 0xf000-0xf007
[ 6.763614] ide1: BM-DMA at 0xf008-0xf00f
[ 6.763631] Probing IDE interface ide0…
[ 6.867832] Floppy drive(s): fd0 is 1.44M
[ 6.888681] FDC 0 is a post-1991 82077
[ 7.052369] hda: Maxtor 6K040L0, ATA DISK drive
[ 7.204196] usb 4-2: new high speed USB device using ehci_hcd and address 2
[ 7.332320] hdb: ST310212A, ATA DISK drive
[ 7.337920] usb 4-2: configuration #1 chosen from 1 choice
[ 7.338780] usb 4-2: New USB device found, idVendor=079b, idProduct=0062
[ 7.338797] usb 4-2: New USB device strings: Mfr=16, Product=32, SerialNumber=0
[ 7.338808] usb 4-2: Product: 802.11b/g USB WLAN
[ 7.338815] usb 4-2: Manufacturer: ZyDAS
[ 7.388409] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 7.388535] hda: UDMA/33 mode selected
[ 7.388656] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 7.388918] hdb: UDMA/33 mode selected
[ 7.389240] Probing IDE interface ide1…
[ 7.576186] usb 4-3: new high speed USB device using ehci_hcd and address 3
[ 7.737190] usb 4-3: configuration #1 chosen from 1 choice
[ 7.738298] usb 4-3: New USB device found, idVendor=07c4, idProduct=0601
[ 7.738315] usb 4-3: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[ 7.738326] usb 4-3: Product: MULTI READER
[ 7.738333] usb 4-3: Manufacturer: Datafab
[ 7.738340] usb 4-3: SerialNumber: 090410000404
[ 8.103865] Initializing USB Mass Storage driver…
[ 8.104448] scsi0 : SCSI emulation for USB Mass Storage devices
[ 8.104977] usbcore: registered new interface driver usb-storage
[ 8.104996] USB Mass Storage support registered.
[ 8.110479] usb-storage: device found at 3
[ 8.110496] usb-storage: waiting for device to settle before scanning
[ 8.346251] Marking TSC unstable due to: TSC halts in idle.
[ 8.404242] hdd: 40X12X48 CD-RW 1.00 20020412, ATAPI CD/DVD-ROM drive
[ 8.460268] hdd: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 8.460464] hdd: UDMA/33 mode selected
[ 8.460937] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 8.461054] ide1 at 0x170-0x177,0x376 on irq 15
[ 8.645850] hda: max request size: 128KiB
[ 10.765619] hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63
[ 10.765830] hda: cache flushes supported
[ 10.766035] hda: hda1 hda2 < hda5 hda6 >
[ 10.808605] hdb: max request size: 128KiB
[ 10.809821] hdb: 20005650 sectors (10242 MB) w/512KiB Cache, CHS=19846/16/63
[ 10.809843] hdb: cache flushes not supported
[ 10.810020] hdb: hdb1
[ 10.848104] hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache
[ 10.848129] Uniform CD-ROM driver Revision: 3.20
[ 11.731228] PM: Starting manual resume from disk
[ 11.855806] kjournald starting. Commit interval 5 seconds
[ 11.855875] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.108956] usb-storage: device scan complete
[ 13.117529] scsi 0:0:0:0: Direct-Access Datafab MULTI READER 9732 PQ: 0 ANSI: 0
[ 13.125661] scsi 0:0:0:1: Direct-Access Datafab MULTI READER 9732 PQ: 0 ANSI: 0
[ 13.134213] scsi 0:0:0:2: Direct-Access Datafab MULTI READER 9732 PQ: 0 ANSI: 0
[ 14.505686] udevd version 125 started
[ 17.096912] Driver ‘sd’ needs updating - please use bus_type methods
[ 17.098878] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 17.100687] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[ 17.102457] sd 0:0:0:2: [sdc] Attached SCSI removable disk
[ 19.728993] input: PC Speaker as /class/input/input1
[ 20.684378] Linux agpgart interface v0.103
[ 20.824838] agpgart: Detected an Intel i810 Chipset.
[ 20.842400] agpgart: AGP aperture is 64M @ 0xd0000000
[ 20.858841] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 20.886740] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 21.100240] Intel 82802 RNG detected
[ 22.004561] input: ImPS/2 Generic Wheel Mouse as /class/input/input2
[ 22.710203] input: Power Button (FF) as /class/input/input3
[ 22.739316] ACPI: Power Button (FF) [PWRF]
[ 22.739575] input: Power Button (CM) as /class/input/input4
[ 22.764430] ACPI: Power Button (CM) [PWRB]
[ 22.764701] input: Sleep Button (CM) as /class/input/input5
[ 22.792289] ACPI: Sleep Button (CM) [SLPB]
[ 22.869830] parport_pc 00:0a: reported by Plug and Play ACPI
[ 22.869937] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 26.546611] gameport: NS558 PnP Gameport is pnp00:0e/gameport0, io 0x201, speed 784kHz
[ 30.100267] usb 4-2: reset high speed USB device using ehci_hcd and address 2
[ 30.234627] phy0: Selected rate control algorithm ‘pid’
[ 31.060568] zd1211rw 4-2:1.0: phy0
[ 31.060674] usbcore: registered new interface driver zd1211rw
[ 32.032767] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[ 33.696498] Adding 746980k swap on /dev/hda5. Priority:-1 extents:1 across:746980k
[ 34.041536] EXT3 FS on hda1, internal journal
[ 34.743966] loop: module loaded
[ 35.709364] kjournald starting. Commit interval 5 seconds
[ 35.712477] EXT3 FS on hda6, internal journal
[ 35.712500] EXT3-fs: mounted filesystem with ordered data mode.
[ 38.655766] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 43.326978] NET: Registered protocol family 10
[ 43.329068] lo: Disabled Privacy Extensions
[ 43.923893] lp0: using parport0 (interrupt-driven).
[ 44.035045] ppdev: user-space parallel port driver
[ 48.055052] RPC: Registered udp transport module.
[ 48.055070] RPC: Registered tcp transport module.
[ 48.192177] Installing knfsd (copyright © 1996 okir@monad.swb.de).
[ 48.337759] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 48.358038] NFSD: starting 90-second grace period
[ 53.672083] eth0: no IPv6 routers present
[ 57.910104] NET: Registered protocol family 5
[ 61.226266] [drm] Initialized drm 1.1.0 20060810
[ 61.246634] ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 61.246668] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 61.247212] [drm] Initialized i810 1.4.0 20030605 on minor 0
[ 61.249122] mtrr: base(0xd0000000) is not aligned on a size(0x180000) boundary
[ 61.872732] [drm] Using v1.4 init.
[ 65.060044] [drm:drm_release] ERROR reclaim_buffers_locked() deadlock. Please rework this
[ 65.060057] driver to use reclaim_buffers_idlelocked() instead.
[ 65.060062] I will go on reclaiming the buffers anyway.
[ 6308.814830] usb 4-2: USB disconnect, address 2
[ 6318.548170] usb 4-2: new high speed USB device using ehci_hcd and address 4
[ 6318.681896] usb 4-2: configuration #1 chosen from 1 choice
[ 6318.796268] usb 4-2: reset high speed USB device using ehci_hcd and address 4
[ 6318.936517] phy1: Selected rate control algorithm ‘pid’
[ 6318.939371] zd1211rw 4-2:1.0: phy1
[ 6318.939727] usb 4-2: New USB device found, idVendor=079b, idProduct=0062
[ 6318.939741] usb 4-2: New USB device strings: Mfr=16, Product=32, SerialNumber=0
[ 6318.939751] usb 4-2: Product: 802.11b/g USB WLAN
[ 6318.939759] usb 4-2: Manufacturer: ZyDAS
bene:/home/benedicte#

[/code]

mais c’est de l’hebreux pour moi…

#8 
[b]
ifconfig wlan0 up[/b]
Pour activer le réseau

Dans [b]dmesg[/b] (pour info)
[code]
[ 6318.939371] zd1211rw 4-2:1.0: phy1
[ 6318.939727] usb 4-2: New USB device found, idVendor=079b, idProduct=0062
[ 6318.939741] usb 4-2: New USB device strings: Mfr=16, Product=32, SerialNumber=0
[ 6318.939751] usb 4-2: Product: 802.11b/g USB WLAN
[ 6318.939759] usb 4-2: Manufacturer: ZyDAS[/code]

ça c'est ton dongle USB


ifconfig wlan0 up
Pour activer le réseau

Dans dmesg (pour info)

[ 6318.939371] zd1211rw 4-2:1.0: phy1 [ 6318.939727] usb 4-2: New USB device found, idVendor=079b, idProduct=0062 [ 6318.939741] usb 4-2: New USB device strings: Mfr=16, Product=32, SerialNumber=0 [ 6318.939751] usb 4-2: Product: 802.11b/g USB WLAN [ 6318.939759] usb 4-2: Manufacturer: ZyDAS

ça c’est ton dongle USB

#9

T’as installé le paquet zd1211-firmware
(voir si le module est chargé : lsmod )
++
Cyrille
(mais active déjà le réseau, puis relance iwlist scanning, etc…)

#10

ifconfig wlan0 up

j’ai comme reponse aucun fichier ou repertoire de ce type

!!!

#11

je re précise la reponse à la commande ifconfig wlan0 up

bene:/home/benedicte# ifconfig wlan0 up
SIOCSIFFLAGS: Aucun fichier ou répertoire de ce type

#12

Que sort le lsmod ? Tu as installé le driver de ta clé ?

#13

lsmod

bene:/home/benedicte# lsmod
Module Size Used by
i810 14784 2
drm 65320 3 i810
appletalk 25984 20
nfsd 186928 13
lockd 54568 1 nfsd
nfs_acl 2912 1 nfsd
auth_rpcgss 33952 1 nfsd
sunrpc 162528 11 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 3936 1 nfsd
ppdev 6468 0
lp 8164 0
ipv6 235396 25
cpufreq_ondemand 6476 0
cpufreq_powersave 1856 0
cpufreq_userspace 3172 0
cpufreq_conservative 5960 0
cpufreq_stats 3776 0
freq_table 4224 2 cpufreq_ondemand,cpufreq_stats
loop 12748 0
snd_mpu401 6152 0
snd_cs4232 11380 0
snd_cmipci 28992 1
snd_cs4231_lib 20512 1 snd_cs4232
snd_pcm_oss 32800 0
snd_mixer_oss 12320 1 snd_pcm_oss
snd_pcm 62660 3 snd_cmipci,snd_cs4231_lib,snd_pcm_oss
snd_opl3_lib 9344 2 snd_cs4232,snd_cmipci
snd_hwdep 6212 1 snd_opl3_lib
snd_page_alloc 7816 2 snd_cs4231_lib,snd_pcm
snd_mpu401_uart 6368 3 snd_mpu401,snd_cs4232,snd_cmipci
arc4 1824 2
snd_seq_dummy 2660 0
ecb 2624 2
crypto_blkcipher 15236 1 ecb
snd_seq_oss 24992 0
snd_seq_midi 5728 0
snd_rawmidi 18496 2 snd_mpu401_uart,snd_seq_midi
zd1211rw 39876 0
firmware_class 6816 1 zd1211rw
mac80211 139808 1 zd1211rw
snd_seq_midi_event 6432 2 snd_seq_oss,snd_seq_midi
cfg80211 21608 1 mac80211
snd_seq 41456 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 17800 4 snd_cs4231_lib,snd_pcm,snd_opl3_lib,snd_seq
snd_seq_device 6380 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 45636 17 snd_mpu401,snd_cs4232,snd_cmipci,snd_cs4231_lib,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 6368 1 snd
ns558 3712 0
gameport 10700 3 snd_cmipci,ns558
parport_pc 22500 1
button 6096 0
parport 30988 3 ppdev,lp,parport_pc
serio_raw 4740 0
psmouse 32336 0
intel_rng 4576 0
rng_core 3940 1 intel_rng
shpchp 25528 0
pci_hotplug 23460 1 shpchp
intel_agp 22524 1
agpgart 28808 3 drm,intel_agp
pcspkr 2432 0
evdev 8000 4
sd_mod 22200 3
ext3 105576 2
jbd 39476 1 ext3
mbcache 7108 1 ext3
ide_cd_mod 27684 1
cdrom 30176 1 ide_cd_mod
ide_disk 10496 4
usb_storage 77120 3
floppy 47844 0
piix 6568 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ehci_hcd 28428 0
ide_core 96168 4 ide_cd_mod,ide_disk,piix,ide_pci_generic
via_rhine 18664 0
mii 4896 1 via_rhine
ata_generic 4676 0
uhci_hcd 18672 0
libata 140448 1 ata_generic
usbcore 118224 5 zd1211rw,usb_storage,ehci_hcd,uhci_hcd
scsi_mod 129548 3 sd_mod,usb_storage,libata
dock 8304 1 libata
thermal 15228 0
processor 32576 2 thermal
fan 4196 0
thermal_sys 10856 3 thermal,processor,fan
bene:/home/benedicte#

pour le driver non, car je pensais que comme il l’avait trouvée et reconnue je n’en avais pas besoin…ou puis-je trouver ce driver ?

en tout cas merci pour ton aide
alain

#14

Le module n’est pas chargé.
Pour l’installer

(attention il faut que ton /etc/apt/sources.list contiennent les dépôts non libres. Eventuellement à mettre à jour donc (ne pas oublier un aptitude update ensuite si c’est ton cas)

En tout cas, tout semble plus oumoins expliqué ici, non ?
wiki.debian.org/zd1211rw

Cyrille

#15

Au fait
wiki.debian.org/zd1211rw

Vérifie donc la version de ton noyau ($ uname -a)

#16

ok il est bon :

Linux bene 2.6.26-2-686 #1 SMP Mon Jun 21 05:58:44 UTC 2010 i686 GNU/Linux

#17

cependant comme j’ai fait une netinstall (machine ancienne avec peu de memoire) se pourrait-il qu’il ne soit pas installé ?

je viens d’aller sur la page qur tu as citée…et telecharger wirelesstools et zd1211-firmware, ni l’un ni l’autre ne veulent s’installer formar de fichier non pris en charge

[b]Impossible d’ouvrir « zd1211-firmware_2.21.0.0-0.1_all.deb »

Type d’archive non pris en charge.[/b]

#18

Install le driver :

Vérifie la présence de ton device

Active le

iwlist scanning doit te retourner ta box

Install. Wicd, Ouvre le point d’association et paramètre ton WIFI.
–> Normalement ça doit marcher.

Je continue demain si tu restes bloqué, là au pieu !!!

Bonne soirée ,

Cyrille

#19

bonne soirée à toi…moi aussi au pieu,je suis dessus depuis hier 8 heures du matin

merci

#20

bene:/home/benedicte# aptitude install zd1211-firmware

Lecture des listes de paquets... Fait Construction de l'arbre des dépendances Lecture des informations d'état... Fait Lecture de l'information d'état étendu Initialisation de l'état des paquets... Fait Écriture de l'information d'état étendu... Fait Lecture des descriptions de tâches... Fait
Impossible de trouver un paquet dont le nom ou la description correspond à « zd1211-firmware »
Impossible de trouver un paquet dont le nom ou la description correspond à « zd1211-firmware »

Les paquets suivants seront ENLEVÉS : 
  consolekit{u} dhcdbd{u} libck-connector0{u} libnl1{u} 

*****  j'en suis au même point .....
  libnm-glib-vpn0{u} libnm-util0{u} libpolkit-dbus2{u} 
  libpolkit-gnome0{u} libpolkit-grant2{u} libpolkit2{u} 
  policykit{u} policykit-gnome{u} 
0 paquets mis à jour, 0 nouvellement installés, 12 à enlever et 0 non mis à jour.
Il est nécessaire de télécharger 0o d'archives. Après dépaquetage, 3498ko seront libérés.
Voulez-vous continuer ? [Y/n/?] Y
Écriture de l'information d'état étendu... Fait
(Lecture de la base de données... 104575 fichiers et répertoires déjà installés.)
Suppression de policykit-gnome ...
Suppression de policykit ...
Suppression de consolekit ...
Suppression de dhcdbd ...
Stopping DHCP D-Bus daemon: dhcdbd.
Suppression de libck-connector0 ...
Suppression de libnl1 ...
Suppression de libnm-glib-vpn0 ...
Suppression de libnm-util0 ...
Suppression de libpolkit-gnome0 ...
Suppression de libpolkit-dbus2 ...
Suppression de libpolkit-grant2 ...
Suppression de libpolkit2 ...
Traitement des actions différées (« triggers ») pour « man-db »...
Lecture des listes de paquets... Fait             
Construction de l'arbre des dépendances       
Lecture des informations d'état... Fait
Lecture de l'information d'état étendu       
Initialisation de l'état des paquets... Fait
Écriture de l'information d'état étendu... Fait
Lecture des descriptions de tâches... Fait       
****************************************************************
****************************************************************
bene:/home/benedicte# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

wmaster0  no wireless extensions.

wlan0     IEEE 802.11  ESSID:""  
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated   
          Tx-Power=0 dBm   
          Retry min limit:7   RTS thr:off   Fragment thr=2352 B   
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0