Demarrage impossible avec usb 2.0

Support Debian
#1

Bonjour,

Mon souci est le suivant: Debian (Squeeze) ne démarre pas lorsque j’active l’usb 2.0 dans le bios. Grub se lance normalement, puis j’obtiens un:

Après quoi le pc m’explique que la partition où se trouve le système n’existe pas.

Fstab est pourtant correct, et de toute manière, l’erreur ne se produit pas lorsque je n’active pas l’usb 2.0.

Le système est monté sur un disque dur ide, en fin de disque:
/home/ sdb1
swap sdb2
/ sdb3
J’ai un second disque dur SATA, mais qui ne contient que des données personnelles.

En fouillant dans le forum, la solution serait peut être de modifier le temps de recherche du système au démarrage, en modifiant ou en ajoutant la ligne rootdelay=… dans grub. Mais j’utilise grub2, et tous les tutoriels valent pour les versions précédentes de grub, via menu.lst…

Si quelqu’un pouvait m’indiquer la marche à suivre, ou toute autre solution à mon problème, ça serait sympa (faire des sauvegardes sur un dd usb sans le 2.0 va me faire vieillir)…

Stef

#2

salut

regarde ici il y a des sujet en resolu (solved)

google.com/search?q=ALERT+!+ … +not+exist

#3

Salut,

Un copié-collé du /etc/fstab serait un plus :slightly_smiling:

#4

Salut,

Voici le contenu de fstab

[quote]#
proc /proc proc defaults 0 0

/ was on /dev/hdb3 during installation

/dev/hdb3 / ext3 errors=remount-ro 0 1

/home was on /dev/hdb1 during installation

UUID=ec48e4ff-4714-44cc-99a4-92f0ea5c49a2 /home ext3 defaults 0 2

swap was on /dev/hdb2 during installation

UUID=4675cc34-7230-44a8-ad0c-3627df52d6b0 none swap sw 0 0

swap was on /dev/sda2 during installation

UUID=0ddeece6-b426-4f15-a732-613745924135 none swap sw 0 0
/dev/scd0 /media/cdrom0 udf,iso9660 user,noauto 0 0

/dev/hda /media/cdrom1 udf,iso9660 user,noauto 0 0

/dev/cdrom1 /media/cdrom1 udf,iso9660 user,noauto 0 0
UUID=51b2d8c6-f5e1-41d2-a834-68f991cb018f /mnt/dd1000 ext3 defaults 0 0[/quote]

Je m’aperçois que j’avais modifié le point de montage de / pour essayer de régler le problème. Voici les uuid que me renvoie blkid,

[quote]/dev/sda1: UUID=“ec48e4ff-4714-44cc-99a4-92f0ea5c49a2” SEC_TYPE=“ext2” TYPE=“ext3”
/dev/sda2: UUID=“4675cc34-7230-44a8-ad0c-3627df52d6b0” TYPE=“swap”
/dev/sdb1: UUID=“51b2d8c6-f5e1-41d2-a834-68f991cb018f” SEC_TYPE=“ext2” TYPE=“ext3”
/dev/sdb2: UUID=“0ddeece6-b426-4f15-a732-613745924135” TYPE=“swap”
/dev/sda3: UUID=“a4745518-8edd-4128-ae44-17c353c518b0” TYPE=“ext3” [/quote]

Je vais remettre l’uid d’origine. Mais le message d’erreur porte bien sur l’inexistence de “a4745…”

Je vais jeter un coup d’oeil au lien.

Stef

#5

Also,

J’ai remis l’uuid d’origine dans fstab, sans miracle (on ne sait jamais !). Et les problèmes similaires résolus concernent plutôt des mauvais uuid, ou grub1. Via ce lien,
ubuntuforums.org/showthread.php?t=1355385

j’ai cru qu’il y avait une solution, mais ce que grub m’affiche en mode édition n’y correspond pas tout à fait, et surtout je ne vois pas du tout ce que vient faire le msdos dans cette affaire (??) - j’étais en double boot avec xp pendant très peu de temps mais j’ai formaté la partition pour installer Debian, et installé grub plusieurs fois au cours de mes essais. Bref, voilà ce que ça donne (copié de grub.cfg):

[quote]insmod part_msdos
insmod ext2
set root=’(hd0,msdos3)'
search --no-floppy --fs-uuid --set a4745518-8edd-4128-ae44-17c353c518b0
echo 'Loading Linux 2.6.32-5-686 …'
linux /boot/vmlinuz-2.6.32-5-686 root=UUID=a4745518-8edd-4128-ae44-17c353c518b0 ro quiet
echo 'Loading initial ramdisk …'
initrd /boot/initrd.img-2.6.32-5-686
[/quote]

Voilà voilà…

Stef

#6

Re,

Il ne faut pas mixer les deux systèmes car c’est au moment où tu valide l’usb que les périphériques changent de nom !

#7

Salut Ggoodluck47,

Je ne comprends pas ce que tu veux dire…Le repérage par uuid et identifiant de partition ?

#8

Re,

A titre d’exemple voici le mien :

UUID=fb6e2e52-5e11-4864-9c27-e6bec8917066 /dos ext4 auto,users,rw,exec,noatime 0 0 UUID=6f3ac882-5574-4f05-8860-d9e7e34b9837 /home ext4 defaults,noatime,errors=remoun$ UUID=63a8b1bb-0a5a-4fa1-915b-e9781d621463 /opt ext4 defaults,noatime,errors=remoun$ UUID=c4c62c96-f37f-4243-8455-6af2f733b94b /tmp ext4 defaults,noatime,errors=remoun$ UUID=d04fc157-d7e5-41b7-9a4c-2162b667a656 /usr ext4 defaults,noatime,errors=remoun$ UUID=070e1a91-b6cc-4722-9ff3-a96fd622aaf2 /var ext4 defaults,noatime,errors=remoun$ UUID=ec1a1a7b-0a22-45ef-a717-5e87cc71837c none swap sw 0 0 UUID=50a4fb3c-5846-4927-8f75-b8bfe10a74cd / ext4 defaults,noatime,errors=remoun$ UUID=c1b7f81d-ce06-4b7f-bbd6-40b26262731c /downloads ext4 auto,users,rw,exec,noatime 0 0 UUID=3f87417b-ed92-4705-9f4f-c9ceb6e1a05b /virtual ext4 auto,users,rw,exec,noatime 0 0

#9

Ca devait être le fichier fstab d’origine que je n’avais jamais modifié, contrairement à ce que je croyais…
Je viens de faire un démarrage (avec l’uuid dans fstab), et ça marche.

Merci, et désolé pour le dérangement, j’aurais dû faire plus gaffe.

Stef

#10

Salut,

Autrement dit dans fstab remplacer :

par

Puis

et redémarrer le système.

Remarque : une seule partition swap suffit

:wink:

Edit : j’ai posté sans avoir vu ta réponse ! désolé mais content de ton résultat
a+

#11

Hélas, Re…

Le problème ne semble pas venir de fstab. :12

Le PC ne démarre que si l’usb 2.0 est réglé dans le bios sur fullspeed, et non sur highspeed (12 M annoncés pour le fullspeed, 480 pour le highspeed - j’en doute).

J’ai réussi à redémarrer une seule fois en highspeed, après avoir démarré en fullspeed, et ça ne marche plus. J’ai testé sur une clé usb, et en fullspeed, j’arrive à un débit de 9-10 M, qui a tendance à baisser régulièrement.

C’est beaucoup moins gênant qu’au départ, mais j’aimerais avoir des infos ou une solution. Est ce un problème de matériel ou de compatibilité avec le matériel ?

Pour ceux que ça peut intéresser (là je suis largué), ma carte mère est une asus M2N68-AMPLUS, j’utilise le pilote propriétaire d’Nvidia. Voici ce que donnent les infos sur le matériel…

Sur l’usb

[quote] lsusb
Bus 002 Device 004: ID 0603:00f2 Novatek Microelectronics Corp.
Bus 002 Device 003: ID 046d:c040 Logitech, Inc. Corded Tilt-Wheel Mouse
Bus 002 Device 002: ID 04b8:0005 Seiko Epson Corp. Printer
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[/quote]

Sur le pc en général…

[quote][ 1.864790] pci 0000:00:0d.0: Boot video device
[ 1.864834] Unpacking initramfs…
[ 2.017779] Freeing initrd memory: 8209k freed
[ 2.021511] audit: initializing netlink socket (disabled)
[ 2.021560] type=2000 audit(1280938235.020:1): initialized
[ 2.021777] highmem bounce pool size: 64 pages
[ 2.021815] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.022733] VFS: Disk quotas dquot_6.5.2
[ 2.022804] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.022890] msgmni has been set to 1727
[ 2.023098] alg: No test for stdrng (krng)
[ 2.023193] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.023244] io scheduler noop registered
[ 2.023279] io scheduler anticipatory registered
[ 2.023315] io scheduler deadline registered
[ 2.023375] io scheduler cfq registered (default)
[ 2.023482] pcieport 0000:00:09.0: irq 24 for MSI/MSI-X
[ 2.023487] pcieport 0000:00:09.0: setting latency timer to 64
[ 2.023539] pcieport 0000:00:0b.0: irq 25 for MSI/MSI-X
[ 2.023542] pcieport 0000:00:0b.0: setting latency timer to 64
[ 2.023593] pcieport 0000:00:0c.0: irq 26 for MSI/MSI-X
[ 2.023596] pcieport 0000:00:0c.0: setting latency timer to 64
[ 2.023677] isapnp: Scanning for PnP cards…
[ 2.377159] isapnp: No Plug & Play device found
[ 2.378060] Linux agpgart interface v0.103
[ 2.378249] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.378366] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.378617] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.378748] PNP: No PS/2 controller found. Probing ports directly.
[ 2.379186] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.379226] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.379300] mice: PS/2 mouse device common for all mice
[ 2.379371] rtc_cmos 00:02: RTC can wake from S4
[ 2.379431] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.379503] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 2.379548] cpuidle: using governor ladder
[ 2.379583] cpuidle: using governor menu
[ 2.379620] No iBFT detected.
[ 2.379889] TCP cubic registered
[ 2.380014] NET: Registered protocol family 10
[ 2.380361] lo: Disabled Privacy Extensions
[ 2.380601] Mobile IPv6
[ 2.380635] NET: Registered protocol family 17
[ 2.380683] Using IPI No-Shortcut mode
[ 2.380755] PM: Resume from disk failed.
[ 2.380759] registered taskstats version 1
[ 2.381026] rtc_cmos 00:02: setting system clock to 2010-08-04 16:10:35 UTC (1280938235)
[ 2.381099] Initalizing network drop monitor service
[ 2.381166] Freeing unused kernel memory: 372k freed
[ 2.381390] Write protecting the kernel text: 2492k
[ 2.381447] Write protecting the kernel read-only data: 916k
[ 2.395917] udev: starting version 158
[ 2.464970] usbcore: registered new interface driver usbfs
[ 2.465027] usbcore: registered new interface driver hub
[ 2.465282] usbcore: registered new device driver usb
[ 2.467911] SCSI subsystem initialized
[ 2.469000] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.469353] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 23
[ 2.469401] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 23 (level, low) -> IRQ 23
[ 2.469475] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 2.469477] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 2.469530] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 2.469596] ehci_hcd 0000:00:02.1: debug port 1
[ 2.469638] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 2.469653] ehci_hcd 0000:00:02.1: irq 23, io mem 0xdfffac00
[ 2.480035] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 2.480098] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.480137] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.482612] libata version 3.00 loaded.
[ 2.482862] usb usb1: Product: EHCI Host Controller
[ 2.482899] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 2.482936] usb usb1: SerialNumber: 0000:00:02.1
[ 2.483130] usb usb1: configuration #1 chosen from 1 choice
[ 2.483191] hub 1-0:1.0: USB hub found
[ 2.483230] hub 1-0:1.0: 10 ports detected
[ 2.483311] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 2.483621] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 22
[ 2.483667] forcedeth 0000:00:07.0: PCI INT A -> Link[LMAC] -> GSI 22 (level, low) -> IRQ 22
[ 2.483718] forcedeth 0000:00:07.0: setting latency timer to 64
[ 2.488512] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 2.545211] forcedeth 0000:00:07.0: ifname eth0, PHY OUI 0x732 @ 3, addr e0:cb:4e:f7:b6:6e
[ 2.545265] forcedeth 0000:00:07.0: highdma pwrctl mgmt gbit lnktim msi desc-v3
[ 2.545354] sata_nv 0000:00:08.0: version 3.5
[ 2.545647] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[ 2.545698] sata_nv 0000:00:08.0: PCI INT A -> Link[LSA0] -> GSI 21 (level, low) -> IRQ 21
[ 2.545783] sata_nv 0000:00:08.0: setting latency timer to 64
[ 2.546004] scsi0 : sata_nv
[ 2.546108] scsi1 : sata_nv
[ 2.546239] ata1: SATA max UDMA/133 cmd 0xe400 ctl 0xe080 bmdma 0xd880 irq 21
[ 2.546279] ata2: SATA max UDMA/133 cmd 0xe000 ctl 0xdc00 bmdma 0xd888 irq 21
[ 2.546551] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 20
[ 2.546594] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 20 (level, low) -> IRQ 20
[ 2.546649] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 2.546652] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 2.546696] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 2.546759] ohci_hcd 0000:00:02.0: irq 20, io mem 0xdfffb000
[ 2.602384] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.602427] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.602476] usb usb2: Product: OHCI Host Controller
[ 2.602512] usb usb2: Manufacturer: Linux 2.6.32-5-686 ohci_hcd
[ 2.602549] usb usb2: SerialNumber: 0000:00:02.0
[ 2.602669] usb usb2: configuration #1 chosen from 1 choice
[ 2.602728] hub 2-0:1.0: USB hub found
[ 2.602771] hub 2-0:1.0: 10 ports detected
[ 2.603165] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 23
[ 2.603209] sata_nv 0000:00:08.1: PCI INT B -> Link[LSA1] -> GSI 23 (level, low) -> IRQ 23
[ 2.603292] sata_nv 0000:00:08.1: setting latency timer to 64
[ 2.603359] scsi2 : sata_nv
[ 2.603443] scsi3 : sata_nv
[ 2.603566] ata3: SATA max UDMA/133 cmd 0xd800 ctl 0xd480 bmdma 0xd000 irq 23
[ 2.603606] ata4: SATA max UDMA/133 cmd 0xd400 ctl 0xd080 bmdma 0xd008 irq 23
[ 2.603685] pata_amd 0000:00:06.0: version 0.4.1
[ 2.603723] pata_amd 0000:00:06.0: setting latency timer to 64
[ 2.603844] scsi4 : pata_amd
[ 2.603946] scsi5 : pata_amd
[ 2.604573] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.604612] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.888360] ata5.00: ATAPI: TSSTcorpCD/DVDW TS-H542A, TS07, max UDMA/33
[ 2.888728] ata5.01: HPA detected: current 295231450, native 312581808
[ 2.888772] ata5.01: ATA-6: ST3160021A, 3.04, max UDMA/100
[ 2.888809] ata5.01: 295231450 sectors, multi 16: LBA48
[ 2.888862] ata5: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0c60000) ACPI=0x701f (60:20:0x15)
[ 2.888865] ata5: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc0c60000) ACPI=0x3f01f (60:20:0x15)
[ 2.904324] ata5.00: configured for UDMA/33
[ 2.922297] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.928452] ata5.01: configured for UDMA/100
[ 3.012055] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.020353] ata1.00: ATA-8: ST31000528AS, CC38, max UDMA/133
[ 3.020394] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.036356] ata1.00: configured for UDMA/133
[ 3.036477] scsi 0:0:0:0: Direct-Access ATA ST31000528AS CC38 PQ: 0 ANSI: 5
[ 3.208041] usb 2-2: new full speed USB device using ohci_hcd and address 2
[ 3.426505] usb 2-2: New USB device found, idVendor=04b8, idProduct=0005
[ 3.426548] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.426587] usb 2-2: Product: USB Printer
[ 3.426623] usb 2-2: Manufacturer: EPSON
[ 3.426657] usb 2-2: SerialNumber: HU11X0408311520440
[ 3.426781] usb 2-2: configuration #1 chosen from 1 choice
[ 3.504069] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.512229] ata2.00: ATAPI: TSSTcorp CDDVDW SH-S223C, SB02, max UDMA/100
[ 3.528241] ata2.00: configured for UDMA/100
[ 3.531850] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW SH-S223C SB02 PQ: 0 ANSI: 5
[ 3.732038] usb 2-3: new low speed USB device using ohci_hcd and address 3
[ 3.854300] ata4: SATA link down (SStatus 0 SControl 300)
[ 3.855758] scsi 4:0:0:0: CD-ROM TSSTcorp CD/DVDW TS-H542A TS07 PQ: 0 ANSI: 5
[ 3.855989] scsi 4:0:1:0: Direct-Access ATA ST3160021A 3.04 PQ: 0 ANSI: 5
[ 3.856128] ata6: port disabled. ignoring.
[ 3.864283] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 3.864400] sd 0:0:0:0: [sda] Write Protect is off
[ 3.864438] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.864451] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[ 3.864579] sda:sr0: scsi3-mmc drive: 52x/52x writer dvd-ram cd/rw xa/form2 cdda tray
[ 3.870196] Uniform CD-ROM driver Revision: 3.20
[ 3.870331] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.873737] sr1: scsi3-mmc drive: 0x/40x writer cd/rw xa/form2 cdda tray
[ 3.873878] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 3.873978] sd 4:0:1:0: [sdb] 295231450 512-byte logical blocks: (151 GB/140 GiB)
[ 3.874178] sd 4:0:1:0: [sdb] Write Protect is off
[ 3.874215] sd 4:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 3.874227] sd 4:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[ 3.874339] sdb: sda1 sda2
[ 3.891806] sdb1 sdb2 sdb3
[ 3.902320] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.909959] sdb: p3 size 181181070 exceeds device capacity, enabling native capacity
[ 3.910063] ata5: soft resetting link
[ 3.946554] usb 2-3: New USB device found, idVendor=046d, idProduct=c040
[ 3.946597] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.946637] usb 2-3: Product: USB-PS/2 Optical Mouse
[ 3.946673] usb 2-3: Manufacturer: Logitech
[ 3.946792] usb 2-3: configuration #1 chosen from 1 choice
[ 3.964736] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.965203] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.965283] sr 4:0:0:0: Attached scsi generic sg2 type 5
[ 3.965339] sd 4:0:1:0: Attached scsi generic sg3 type 0
[ 4.192317] ata5.01: n_sectors mismatch 295231450 != 312581808
[ 4.192358] ata5.01: new n_sectors matches native, probably late HPA unlock, n_sectors updated
[ 4.200386] ata5: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0c60000) ACPI=0x701f (60:20:0x15)
[ 4.200390] ata5: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc0c60000) ACPI=0x3f01f (60:20:0x15)
[ 4.220333] ata5.00: configured for UDMA/33
[ 4.240431] ata5.01: configured for UDMA/100
[ 4.240726] ata5: EH complete
[ 4.240870] sd 4:0:1:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 4.241136] sdb: detected capacity change from 151158502400 to 160041885696
[ 4.241178] sdb:
[ 4.252048] usb 2-4: new low speed USB device using ohci_hcd and address 4
[ 4.258154] sdb1 sdb2 sdb3
[ 4.276501] sd 4:0:1:0: [sdb] Attached SCSI disk
[ 4.277713] sdb: detected capacity change from 0 to 160041885696
[ 4.465598] usb 2-4: New USB device found, idVendor=0603, idProduct=00f2
[ 4.465641] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.465682] usb 2-4: Product: USB Keyboard
[ 4.465717] usb 2-4: Manufacturer: NOVATEK
[ 4.465843] usb 2-4: configuration #1 chosen from 1 choice
[ 4.478362] usbcore: registered new interface driver hiddev
[ 4.484768] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-3/2-3:1.0/input/input0
[ 4.484884] generic-usb 0003:046D:C040.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-3/input0
[ 4.489793] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input1
[ 4.489897] generic-usb 0003:0603:00F2.0002: input,hidraw1: USB HID v1.10 Keyboard [NOVATEK USB Keyboard] on usb-0000:00:02.0-4/input0
[ 4.502692] input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.1/input/input2
[ 4.502839] generic-usb 0003:0603:00F2.0003: input,hiddev0,hidraw2: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:02.0-4/input1
[ 4.502914] usbcore: registered new interface driver usbhid
[ 4.502953] usbhid: v2.6:USB HID core driver
[ 4.689563] PM: Starting manual resume from disk
[ 4.689612] PM: Resume from partition 8:2
[ 4.689614] PM: Checking hibernation image.
[ 4.689829] PM: Error -22 checking image file
[ 4.689831] PM: Resume from disk failed.
[ 4.721728] kjournald starting. Commit interval 5 seconds
[ 4.721781] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.739278] udev: starting version 158
[ 7.458198] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 7.458255] ACPI: Power Button [PWRB]
[ 7.458338] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 7.458388] ACPI: Power Button [PWRF]
[ 7.565528] tpm_tis 00:0b: 1.2 TPM (device-id 0xFFFF, rev-id 255)
[ 7.565640] tpm_tis 00:0b: tpm_transmit: tpm_send: error 4294967291
[ 7.565725] tpm_tis 00:0b: tpm_transmit: tpm_send: error 4294967291
[ 7.565793] tpm_tis 00:0b: tpm_transmit: tpm_send: error 4294967291
[ 7.623182] processor LNXCPU:00: registered as cooling_device0
[ 7.623245] processor LNXCPU:01: registered as cooling_device1
[ 7.670225] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 7.822459] parport_pc 00:05: reported by Plug and Play ACPI
[ 7.822541] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 7.992834] i2c i2c-0: nForce2 SMBus adapter at 0x600
[ 7.992889] i2c i2c-1: nForce2 SMBus adapter at 0x700
[ 7.996989] usblp1: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
[ 7.997060] usbcore: registered new interface driver usblp
[ 8.735422] nvidia: module license ‘NVIDIA’ taints kernel.
[ 8.735464] Disabling lock debugging due to kernel taint
[ 9.602095] ACPI: PCI Interrupt Link [LMC9] enabled at IRQ 22
[ 9.602138] nvidia 0000:00:0d.0: PCI INT A -> Link[LMC9] -> GSI 22 (level, low) -> IRQ 22
[ 9.602191] nvidia 0000:00:0d.0: setting latency timer to 64
[ 9.602194] vgaarb: device changed decodes: PCI:0000:00:0d.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 9.602367] NVRM: loading NVIDIA UNIX x86 Kernel Module 195.36.24 Thu Apr 22 09:18:20 PDT 2010
[ 9.896370] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 21
[ 9.896414] HDA Intel 0000:00:05.0: PCI INT B -> Link[LAZA] -> GSI 21 (level, low) -> IRQ 21
[ 9.896465] hda_intel: Disable MSI for Nvidia chipset
[ 9.896518] HDA Intel 0000:00:05.0: setting latency timer to 64
[ 10.452100] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:05.0/input/input6
[ 11.356099] Adding 2040244k swap on /dev/sdb2. Priority:-1 extents:1 across:2040244k
[ 11.369909] Adding 2562356k swap on /dev/sda2. Priority:-2 extents:1 across:2562356k
[ 11.747399] EXT3 FS on sdb3, internal journal
[ 11.848525] loop: module loaded
[ 12.650409] kjournald starting. Commit interval 5 seconds
[ 12.650849] EXT3 FS on sdb1, internal journal
[ 12.650912] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.693959] kjournald starting. Commit interval 5 seconds
[ 12.693968] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 12.694367] EXT3 FS on sda1, internal journal
[ 12.694429] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.014410] forcedeth 0000:00:07.0: irq 27 for MSI/MSI-X
[ 14.113549] fuse init (API version 7.13)
[ 20.945717] Bluetooth: Core ver 2.15
[ 20.945793] NET: Registered protocol family 31
[ 20.945829] Bluetooth: HCI device and connection manager initialized
[ 20.945868] Bluetooth: HCI socket layer initialized
[ 21.046150] Bluetooth: L2CAP ver 2.14
[ 21.046187] Bluetooth: L2CAP socket layer initialized
[ 21.049686] Bluetooth: RFCOMM TTY layer initialized
[ 21.049732] Bluetooth: RFCOMM socket layer initialized
[ 21.049768] Bluetooth: RFCOMM ver 1.11
[ 21.522192] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 21.522233] Bluetooth: BNEP filters: protocol multicast
[ 21.579729] Bridge firewalling registered
[ 22.264495] Bluetooth: SCO (Voice Link) ver 0.6
[ 22.264534] Bluetooth: SCO socket layer initialized
[ 24.480021] eth0: no IPv6 routers present
[ 25.387131] lp0: using parport0 (interrupt-driven).
[ 25.520059] ppdev: user-space parallel port driver
[ 27.579807] powernow-k8: Found 1 AMD Athlon™ II X2 245 Processor processors (2 cpu cores) (version 2.20.00)
[ 27.579819] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
[ 27.579820] [Firmware Bug]: powernow-k8: Try again with latest BIOS.
[ 35.321707] CPU0 attaching NULL sched-domain.
[ 35.321712] CPU1 attaching NULL sched-domain.
[ 35.360146] CPU0 attaching sched-domain:
[ 35.360149] domain 0: span 0-1 level MC
[ 35.360152] groups: 0 1
[ 35.360156] CPU1 attaching sched-domain:
[ 35.360157] domain 0: span 0-1 level MC
[ 35.360159] groups: 1 0
[/quote]

Stef