Bonjour,
J’ai parametré mon ftab de manière à monter plusieur disques dur dans le dossier /media
Le problème est que parfois, quand je fait
J’ai :
[quote]Disk /dev/hda: 61.4 GB, 61492838400 bytes
255 heads, 63 sectors/track, 7476 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x11febea3
Device Boot Start End Blocks Id System
/dev/hda1 7295 7476 1461915 82 Linux swap / Solaris
/dev/hda2 * 1 1216 9767488+ 83 Linux
/dev/hda3 1217 7294 48821535 83 Linux
Partition table entries are not in disk order
Disk /dev/hdb: 40.0 GB, 40020664320 bytes
255 heads, 63 sectors/track, 4865 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x0f8000b1
Device Boot Start End Blocks Id System
/dev/hdb1 1 4865 39078081 83 Linux
Disk /dev/hde: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x000e83cc
Device Boot Start End Blocks Id System
/dev/hde1 1 60801 488384001 fd Linux raid autodetect
Disk /dev/hdg: 500.1 GB, 500107862016 bytes
255 heads, 63 sectors/track, 60801 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x0000d186
Device Boot Start End Blocks Id System
/dev/hdg1 1 60801 488384001 fd Linux raid autodetect
Disk /dev/md0: 1000.2 GB, 1000210300928 bytes
2 heads, 4 sectors/track, 244191968 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Disk identifier: 0x00000000
Disk /dev/md0 doesn’t contain a valid partition table
Disk /dev/sde: 400.0 GB, 400088457216 bytes
255 heads, 63 sectors/track, 48641 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x52ea3501
Device Boot Start End Blocks Id System
/dev/sde1 1 48641 390708801 83 Linux
Disk /dev/sdf: 81.9 GB, 81964302336 bytes
255 heads, 63 sectors/track, 9964 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x99609960
Device Boot Start End Blocks Id System
/dev/sdf1 1 9964 80035798+ 83 Linux
SCSERVER:/home/flamme/Desktop#
[/quote]
Et que, et bien parfois, ça change, par exemple :
/dev/sdf1 devient /dev/sda1
/dev/sde1 devient /dev/sdb1
Bref, Les disques qui changent, sont en externe, raccordé en USB. J’allume toujous ces disques avant l’ordinateur, qui m’as fois est rarement éteint, puisqu’il fait office de serveur.
On m’as parlé de fixer, les disques avec un id. Je ne connais pas cette méthode, mais si vous en savez un peu plus que moi…
Es-ce le fameux Disk identifier en dessous ?
Comment dois-je configurer mon fstab
Merci d’avance.