Petit nouveau

Pause Café
#1

Et bien bonjour à tous
j’ai fait le grand saut d’une ubuntu 5.10 à Lenny à l’occasion de la reception de mon Vostro1700.

  • Je suis passé par le driver NVidia (et non pas par la procédure debian) pour ma carte 8600MGT

  • J’ai eu quelques souci avec le son :
    aplay -l
    **** List of PLAYBACK Hardware Devices ****
    card 0: Intel [HDA Intel], device 0: STAC92xx Analog [STAC92xx Analog]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    réglé par la compil du kernel 2.6.22.9 avec le son en dur

  • J’ai encore des soucis avec le touchpad (il semblerait que ce ne soit pas un synaptics…) :
    cat /var/log/Xorg.0.log |grep synaptics
    (II) LoadModule: “synaptics”
    (II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
    (II) Module synaptics: vendor=“X.Org Foundation”
    (II) LoadModule: “synaptics”
    (II) Reloading /usr/lib/xorg/modules/input//synaptics_drv.so
    Synaptics Touchpad no synaptics event device found (checked 18 nodes)
    (EE) Synaptics Touchpad no synaptics touchpad detected and no repeater device
    (II) UnloadModule: “synaptics”

J’ai encore des ennuis avec le wifi (ipw3945 installé avec m-a sur mon kernel 2.6.22.9) mais je m’accroche
voila

#2

[size=150]Olà [/size]et Bienvenue 8)

#3

Bonjour,
Je suis en 2.6.22-4 de debian, avec nvidia et ipw3945 compilés à la mode debian qui fonctionnent nickel.
Pour info, les sources de kernel.org ne sont pas patchées avec les patchs spécifiques debian qui leur permettent de bien fonctionner sous debian, et le pilote nvidia trouvé sur le site supprime des choses en s’installant et gène le bon fonctionnement d’apt sur certaines mises à jour. il ne faut donc utiliser ni l’un ni l’autre si on veut fonctionner longtemps avec des mises à jour régulières.

#4

merci mattotop
c’est probablement ce que je vais faire sous peu. Le Vostro est tout neuf et avant de l’utiliser en production, je comptais expérimenter un peu tout azimut sans risquer quoi que ce soit point de vue ‘taf’.

Au fait as tu le même type de config que moi? Je me pose actuellement pas mal de questions (pardon si c’est questions ont été déjà traitées) Est ce que le kernel 2.6.22-4 a réglé le probleme avec le driver nvidia et le son (cela ne me semble pas évident sans passage à alsa 1.0.15 ou compilation en dur du driver, je me trompe?)? La nvidia 8600MGT est compatible avec une compil “à la debian” des drivers du dépots (je n’ai que les legacy 1.0.7185 et le kernel common de 2005), j’ai installé la version NVIDIA-linux-X86.100.14.19 ? Est ce qu’il sera possible d’activer le suspend si je n’utilise pas cette dernière version?

A toute fin utile, voici ma config
lspci -vv
00:00.0 Host bridge: Intel Corporation Mobile Memory Controller Hub (rev 0c)
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information

00:01.0 PCI bridge: Intel Corporation Mobile PCI Express Root Port (rev 0c) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-feafffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [88] Subsystem: Dell Unknown device 0229
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41c1
Capabilities: [a0] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise-
Slot: Number 1, PowerLimit 75.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Virtual Channel
Capabilities: [140] Unknown (5)

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f20 [size=32]

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 6f00 [size=32]

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 2, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41c9
Capabilities: [90] Subsystem: Dell Unknown device 0229
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)

00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: f9f00000-f9ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41d1
Capabilities: [90] Subsystem: Dell Unknown device 0229
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)

00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f9c00000-f9efffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 4
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 5, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41d9
Capabilities: [90] Subsystem: Dell Unknown device 0229
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f80 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 6f60 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 6f40 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: f9b00000-f9bfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Dell Unknown device 0229

00:1f.0 ISA bridge: Intel Corporation Mobile LPC Interface Controller (rev 02)
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information

00:1f.1 IDE interface: Intel Corporation Mobile IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 6fa0 [size=16]

00:1f.2 IDE interface: Intel Corporation Mobile SATA IDE Controller (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 6eb0 [size=8]
Region 1: I/O ports at 6eb8 [size=4]
Region 2: I/O ports at 6ec0 [size=8]
Region 3: I/O ports at 6ec8 [size=4]
Region 4: I/O ports at 6ee0 [size=16]
Region 5: I/O ports at eff0 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at febfbf00 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 10c0 [size=32]

01:00.0 VGA compatible controller: nVidia Corporation Unknown device 0407 (rev a1) (prog-if 00 [VGA])
Subsystem: Dell Unknown device 0229
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at df00 [size=128]
[virtual] Expansion ROM at fea00000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <512ns, L1 <4us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x16, ASPM L0s L1, Port 0
Link: Latency L0s <512ns, L1 <4us
Link: ASPM L0s L1 Enabled RCB 128 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
Capabilities: [600] Unknown (11)

03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
Subsystem: Dell Unknown device 01f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f9bfe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832 (rev 05) (prog-if 10 [OHCI])
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f9bfd800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+

03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) (prog-if 01)
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
Region 0: Memory at f9bfd400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 12)
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f9bfd500 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f9bfd600 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

03:01.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
Subsystem: Dell Unknown device 0229
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at f9bfd700 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

0c:00.0 Network controller: Intel Corporation Unknown device 4229 (rev 61)
Subsystem: Intel Corporation Unknown device 1121
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f9ffe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <512ns, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number 1d-64-82-ff-ff-e8-13-00

#5

Installer les sources kernel.org et le nvidia du site, c’est plutot ça qui relève de l’experimentation sous debian.
Pour ce qui est des similarités entre nos configs, je crois qu’elles sont fortuites: je suis sur un acer 9423WSMi, et il y a des extensions Dell que je n’ai pas.
Pour ta 8600, elle est supportée, mais il faudra prendre le pilote sid.
Celà ne nécessite pas une install en sid, mais pour un usage laptop, la sid est plutot bien: elle n’a d’unstable que le nom, et les petites douleurs que ça provoque n’ont rien de comparable avec les grosses baffe qu’on se prend sur une famille d’OS que je ne nommerais pas, et sont largement compensées par une panoplie de fonctionnalités pour portable disponibles uniquement en sid (detection pnp ameliorée).
Pour le nvidia, comme l’ipw3945, je dois dire que les dernières mises à jour ne se sont pas faites forcément toute seules, mais à force on y arrive.
Sur un Dell, le suspend doit être plus normalisé que sur d’autres archis, mais je ne parierais rien.
Ah oui: je suis bien sûr en 64bits.
sinon:

roc@roc:~/.freeciv/saves$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: nVidia Corporation G72M [Quadro NVS 110M/GeForce Go 7300] (rev a1) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02) 0a:06.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:06.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) 0a:06.3 Generic system peripheral [0805]: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller

#6

merci pour tes conseils mattotop
je vais donc entrer dans mon sources.list les references à sid et voir ce que cela donne.

#7

[quote=“douarn”]merci pour tes conseils mattotop
je vais donc entrer dans mon sources.list les references à sid et voir ce que cela donne.[/quote]Attends, lis ça:
forum.debian-fr.org/viewtopic.php?t=5659

#8

merci, ça va m’être bien util

#9

tsalu! et oulà heureusement que tu est un “ptit nouveau”

#10

tsalu eartells,
tu t’es trouvé un pmp ?

#11

c’est quoi un pmp?

#12

(PMP: portable multimedia player) le lecteur multimedia à disque dur que tu cherchais.

#13

oh, bon je chercheis un multimedia mais pas forcement à disque dur… j’ai fini pour penser que c’est mieux flash pour des petites quantités de données (et pour mon portemonais)

j’ai pas encore trouvé, non. hier soir après avoir mis sur un forum l’annonce de vente de mon zen micro par pieces et ses accesoires j’ai essaié a nouveau s’il marche. pendant quelques heures j’ai cru qu’il marchait!!!
ce matin il est à nouveau bloqué.
Je suis très très degoutée

d’un autre coté… j’aurai ptetre un ptit jouet nouveau…
et un gros trou sur mes économies

#14

Salut et bienvenue :slightly_smiling:

#15

quote="eartells"
c’est mieux flash pour des petites quantités de données (et pour mon portemonais)
(…)[/quote]En plus, c’est moins fragile, parcequ’il n’y a pas de pièces mécaniques.

#16

c’est souvent comme cela que ça se passe (le principe des vases communicants à ce qu’on dit) :unamused:

J’en reviens à mon V43, ses 128Mo de ram, de son DD de 30Go, de ses formats de lecture (mp3, ogg, wma, wmv, divx, …) et de la bidouille qu’il est possible de faire (attention mode geek)
jbmm.fr/forum/index.php?show … ntry142323
En plus, avec le portage de X11, il devient possible de le piloter à la souris et au clavier et d’utiliser les applications de la debian sarge mipsel… (la seule limitation embêtante c’est la taille de l’écran (480x272)). j’ai testé d’abord antiword puis matchbox, endeavour2, gqview et xvkbd… ça marche, j’ai pas testé en profondeur mais les premiers tests laissent à penser que cela devrait être assez simple en terme de portage …

(je ne suis pas actionnaire de digital cube, juste impressionné par les possibilités du bidules et désapointé par la confidentialité qui l’entoure en France (en fait il faudrait plutôt dire dans tout le monde sauf en Corée du Sud))

#17

C’est sûr un DD c’est fragile… mais cela se change.
Je me suis acheté un toshiba de 20go pour faire mes tests. Je l’ai formaté à l’image du DD d’origine, ouvert le bidule et … ça marche (merci Philou du tuyau). Bon d’accord la garantie n’est plus. Mais entre nous j’avais eu un souci au début et renvoyé en Corée parce qu’il était sous garantie et franchement j’ai attendu 4 mois pour le revoir… Alors la garantie… :confused:
Ce que j’aimerais maintenant c’est y mettre

  • streamtuner pour la webradio
  • il y a les modules pour la cynergyt² dans le kernel 2.6.11 pour la tnt
  • il y a le module pl2303 pour un gps mouse holux
    Enfin voila je ne sais pas quand mais je vais essayer tout ça. :unamused:
#18

Les PC Dell ça m’a toujours fait penser à ça :

Hit Dell to Enter Setup

#19

le probleme avec ce truc est le prix… vraiment si je depense 500 euros je m’achette un nouveau Nil moi!

#20

Je comprend … fait au mieux