redémarrage intempestif et ventilos

[deepo93]

bonjour à tous,

voila j’ai 2 problèmes:

1. mon ordi redémarre (ou se met en veille 2 secondes et redémarre aussitôt) dès que je ne bouge plus la souris pendant 10 minutes.
2. mes ventilos tournent à fond au démarrage mais lorsque l’ordi redémarre intempestivement ils tournent au minimum. J’ai réglé fancontrol mais sans succès… j’ai dépoussiéré tout l’intérieur et laissé le capot ouvert.

Voici ma config

[quote]00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
Subsystem: Hewlett-Packard Company Device 2a78
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0b <?>

00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f8000000-fbffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Capabilities: [88] Subsystem: Intel Corporation Device 0000
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [a0] Express Root Port (Slot+), MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [140] Root Complex Link
Kernel driver in use: pcieport

00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Device 2a78
Flags: bus master, fast devsel, latency 0, IRQ 43
Memory at fdffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [130] Root Complex Link
Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Hewlett-Packard Company Device 2a78
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel
Capabilities: [180] Root Complex Link
Kernel driver in use: pcieport

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fde00000-00000000fdefffff
Capabilities: [50] Subsystem: Hewlett-Packard Company Device 2a78

00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Hewlett-Packard Company Device 2a78
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.2 IDE interface: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device 2a78
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at f900 [size=16]
Capabilities: [70] Power Management version 2
Kernel driver in use: ata_piix

00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 01)
Subsystem: Hewlett-Packard Company Device 2a78
Flags: medium devsel, IRQ 19
I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus

01:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 9300 GE] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Device 1b0a:9004
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
I/O ports at cf00 [size=128]
[virtual] Expansion ROM at fb000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 3
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nouveau

02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 01)
Subsystem: Hewlett-Packard Company Device 2a78
Flags: bus master, fast devsel, latency 0, IRQ 42
I/O ports at de00 [size=256]
Memory at fdbff000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at fdc00000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Capabilities: [48] Vital Product Data
Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+
Capabilities: [60] Express Endpoint, MSI 00
Capabilities: [84] Vendor Specific Information: Len=4c <?>
Capabilities: [100] Advanced Error Reporting
Capabilities: [12c] Virtual Channel
Capabilities: [148] Device Serial Number 05-00-00-00-36-4c-e0-00
Capabilities: [154] Power Budgeting <?>
Kernel driver in use: r8169[/quote]
et ma version

[ul]Linux Host-002 3.2.0-4-amd64 #1 SMP Debian 3.2.65-1+deb7u1 x86_64 GNU/Linux
[/ul]

en espérant que quelqu’un puisse m’aider, je précise que je suis super débutant avec debian… merci pour votre compréhension.

[Zbf]

Donc en gros, la mise en veille (le fait que tu ne bouges plus la souris) te fait capoter ton install.
Ca n’est pas normal.
Juste après que ça arrive, vérifie tes logs.

C’est un ordi de bureau ou portable ?
Quelles options as-tu à disposition pour régler les paramètres de mise en veille depuis ton environnement graphique ?

[deepo93]

bonjour et merci pour la réponse!

Voici le résultat de la commande après redémarrage :

[quote][ 0.172511] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.172514] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.172517] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff]
[ 0.172521] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.172582] pci 0000:02:00.0: [10ec:8136] type 0 class 0x000200
[ 0.172600] pci 0000:02:00.0: reg 10: [io 0xde00-0xdeff]
[ 0.172631] pci 0000:02:00.0: reg 18: [mem 0xfdbff000-0xfdbfffff 64bit]
[ 0.172666] pci 0000:02:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.172743] pci 0000:02:00.0: supports D1 D2
[ 0.172745] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.172766] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with ‘pcie_aspm=force’
[ 0.172776] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.172780] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 0.172784] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff]
[ 0.172789] pci 0000:00:1c.0: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[ 0.172851] pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
[ 0.172855] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.172859] pci 0000:00:1e.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 0.172864] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
[ 0.172867] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.172870] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.172872] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.172875] pci 0000:00:1e.0: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.172877] pci 0000:00:1e.0: bridge window [mem 0xbff00000-0xfebfffff] (subtractive decode)
[ 0.172892] ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PRT]
[ 0.173031] ACPI: PCI Interrupt Routing Table [_SB.PCI0.PEX0.PRT]
[ 0.173081] ACPI: PCI Interrupt Routing Table [_SB.PCI0.HUB0._PRT]
[ 0.173147] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.173151] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 0.173153] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.177698] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 0.177750] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.177801] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 *7 9 10 11 12 14 15)
[ 0.177850] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 0.177900] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.177950] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.178000] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 0.178051] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 0.178163] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.178163] vgaarb: loaded
[ 0.178163] vgaarb: bridge control possible 0000:01:00.0
[ 0.178163] PCI: Using ACPI for IRQ routing
[ 0.184081] PCI: pci_cache_line_size set to 64 bytes
[ 0.184124] reserve RAM buffer: 000000000009f400 - 000000000009ffff
[ 0.184126] reserve RAM buffer: 00000000bfe90000 - 00000000bfffffff
[ 0.184251] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.184256] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.184260] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.188131] Switching to clocksource hpet
[ 0.190099] pnp: PnP ACPI init
[ 0.190120] ACPI: bus type pnp registered
[ 0.190226] pnp 00:00: [bus 00-ff]
[ 0.190229] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.190232] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.190234] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.190236] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.190238] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[ 0.190241] pnp 00:00: [mem 0xbff00000-0xfebfffff window]
[ 0.190305] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.190372] pnp 00:01: [io 0x0010-0x001f]
[ 0.190374] pnp 00:01: [io 0x0022-0x003f]
[ 0.190376] pnp 00:01: [io 0x0044-0x005f]
[ 0.190378] pnp 00:01: [io 0x0062-0x0063]
[ 0.190380] pnp 00:01: [io 0x0065-0x006f]
[ 0.190382] pnp 00:01: [io 0x0074-0x007f]
[ 0.190383] pnp 00:01: [io 0x0091-0x0093]
[ 0.190385] pnp 00:01: [io 0x00a2-0x00bf]
[ 0.190387] pnp 00:01: [io 0x00e0-0x00ef]
[ 0.190389] pnp 00:01: [io 0x04d0-0x04d1]
[ 0.190391] pnp 00:01: [io 0x0800-0x087f]
[ 0.190392] pnp 00:01: [io 0x0290-0x0297]
[ 0.190394] pnp 00:01: [io 0x0880-0x088f]
[ 0.190451] system 00:01: [io 0x04d0-0x04d1] has been reserved
[ 0.190454] system 00:01: [io 0x0800-0x087f] has been reserved
[ 0.190456] system 00:01: [io 0x0290-0x0297] has been reserved
[ 0.190459] system 00:01: [io 0x0880-0x088f] has been reserved
[ 0.190462] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.190475] pnp 00:02: [dma 4]
[ 0.190477] pnp 00:02: [io 0x0000-0x000f]
[ 0.190479] pnp 00:02: [io 0x0080-0x0090]
[ 0.190481] pnp 00:02: [io 0x0094-0x009f]
[ 0.190483] pnp 00:02: [io 0x00c0-0x00df]
[ 0.190512] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.190571] pnp 00:03: [irq 0 disabled]
[ 0.190584] pnp 00:03: [irq 8]
[ 0.190586] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 0.190620] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.190649] pnp 00:04: [io 0x0070-0x0073]
[ 0.190681] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.190691] pnp 00:05: [io 0x0061]
[ 0.190722] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.190732] pnp 00:06: [io 0x00f0-0x00ff]
[ 0.190738] pnp 00:06: [irq 13]
[ 0.190769] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.191028] pnp 00:07: [irq 12]
[ 0.191063] pnp 00:07: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.191088] pnp 00:08: [io 0x0060]
[ 0.191090] pnp 00:08: [io 0x0064]
[ 0.191096] pnp 00:08: [irq 1]
[ 0.191130] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.191150] pnp 00:09: [io 0x0400-0x04bf]
[ 0.191196] system 00:09: [io 0x0400-0x04bf] has been reserved
[ 0.191199] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.191220] pnp 00:0a: [mem 0xffb80000-0xffbfffff]
[ 0.191253] pnp 00:0a: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.191452] pnp 00:0b: [mem 0xe0000000-0xefffffff]
[ 0.191508] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.191511] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.191588] pnp 00:0c: [mem 0x000f0000-0x000fffff]
[ 0.191591] pnp 00:0c: [mem 0xbff00000-0xbfffffff]
[ 0.191593] pnp 00:0c: [mem 0xfed00000-0xfed000ff]
[ 0.191595] pnp 00:0c: [mem 0xbfe90000-0xbfefffff]
[ 0.191597] pnp 00:0c: [mem 0x00000000-0x0009ffff]
[ 0.191599] pnp 00:0c: [mem 0x00100000-0xbfe8ffff]
[ 0.191601] pnp 00:0c: [mem 0xfec00000-0xfec00fff]
[ 0.191603] pnp 00:0c: [mem 0xfed13000-0xfed1dfff]
[ 0.191605] pnp 00:0c: [mem 0xfed20000-0xfed8ffff]
[ 0.191607] pnp 00:0c: [mem 0xfee00000-0xfee00fff]
[ 0.191609] pnp 00:0c: [mem 0xffb00000-0xffb7ffff]
[ 0.191611] pnp 00:0c: [mem 0xfff00000-0xffffffff]
[ 0.191613] pnp 00:0c: [mem 0x000e0000-0x000effff]
[ 0.191672] system 00:0c: [mem 0x000f0000-0x000fffff] could not be reserved
[ 0.191675] system 00:0c: [mem 0xbff00000-0xbfffffff] has been reserved
[ 0.191678] system 00:0c: [mem 0xfed00000-0xfed000ff] has been reserved
[ 0.191681] system 00:0c: [mem 0xbfe90000-0xbfefffff] could not be reserved
[ 0.191684] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.191687] system 00:0c: [mem 0x00100000-0xbfe8ffff] could not be reserved
[ 0.191690] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.191693] system 00:0c: [mem 0xfed13000-0xfed1dfff] has been reserved
[ 0.191696] system 00:0c: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.191699] system 00:0c: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.191701] system 00:0c: [mem 0xffb00000-0xffb7ffff] has been reserved
[ 0.191704] system 00:0c: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.191707] system 00:0c: [mem 0x000e0000-0x000effff] has been reserved
[ 0.191710] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.191717] pnp: PnP ACPI: found 13 devices
[ 0.191719] ACPI: ACPI bus type pnp unregistered
[ 0.198650] PCI: max bus depth: 1 pci_try_num: 2
[ 0.198677] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb01ffff pref]
[ 0.198680] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.198683] pci 0000:00:01.0: bridge window [io 0xc000-0xcfff]
[ 0.198687] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff]
[ 0.198690] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.198696] pci 0000:02:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref]
[ 0.198698] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.198701] pci 0000:00:1c.0: bridge window [io 0xd000-0xdfff]
[ 0.198706] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff]
[ 0.198710] pci 0000:00:1c.0: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[ 0.198715] pci 0000:00:1e.0: PCI bridge to [bus 05-05]
[ 0.198718] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.198723] pci 0000:00:1e.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 0.198727] pci 0000:00:1e.0: bridge window [mem 0xfde00000-0xfdefffff 64bit pref]
[ 0.198749] pci 0000:00:01.0: setting latency timer to 64
[ 0.198758] pci 0000:00:1c.0: setting latency timer to 64
[ 0.198766] pci 0000:00:1e.0: setting latency timer to 64
[ 0.198769] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.198772] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.198774] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.198776] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.198778] pci_bus 0000:00: resource 8 [mem 0xbff00000-0xfebfffff]
[ 0.198781] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
[ 0.198783] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff]
[ 0.198785] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.198788] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 0.198790] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff]
[ 0.198793] pci_bus 0000:02: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[ 0.198795] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.198797] pci_bus 0000:05: resource 1 [mem 0xfdd00000-0xfddfffff]
[ 0.198800] pci_bus 0000:05: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref]
[ 0.198802] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7]
[ 0.198804] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff]
[ 0.198806] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.198809] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000dffff]
[ 0.198811] pci_bus 0000:05: resource 8 [mem 0xbff00000-0xfebfffff]
[ 0.198875] NET: Registered protocol family 2
[ 0.200774] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.202088] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.208152] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.208877] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.208880] TCP reno registered
[ 0.208900] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.208955] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.209154] NET: Registered protocol family 1
[ 0.209201] pci 0000:01:00.0: Boot video device
[ 0.209208] PCI: CLS 64 bytes, default 64
[ 0.209266] Unpacking initramfs…
[ 0.435728] Freeing initrd memory: 10240k freed
[ 0.440914] audit: initializing netlink socket (disabled)
[ 0.440929] type=2000 audit(1422467392.436:1): initialized
[ 0.453060] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.453698] VFS: Disk quotas dquot_6.5.2
[ 0.453729] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.453802] msgmni has been set to 6038
[ 0.453974] alg: No test for stdrng (krng)
[ 0.454006] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.454009] io scheduler noop registered
[ 0.454011] io scheduler deadline registered
[ 0.454027] io scheduler cfq registered (default)
[ 0.454094] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.454127] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.454180] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.454214] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.454299] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.454321] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.454322] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.454641] intel_idle: does not run on family 6 model 15
[ 0.454667] ERST: Table is not found!
[ 0.454669] GHES: HEST is not enabled!
[ 0.454745] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.500478] Linux agpgart interface v0.103
[ 0.500679] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.503023] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.503030] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.503174] mousedev: PS/2 mouse device common for all mice
[ 0.503222] rtc_cmos 00:04: RTC can wake from S4
[ 0.503326] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.503350] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.503362] cpuidle: using governor ladder
[ 0.503364] cpuidle: using governor menu
[ 0.503580] TCP cubic registered
[ 0.503619] NET: Registered protocol family 10
[ 0.504092] Mobile IPv6
[ 0.504095] NET: Registered protocol family 17
[ 0.504100] Registering the dns_resolver key type
[ 0.504241] PM: Hibernation image not present or could not be loaded.
[ 0.504254] registered taskstats version 1
[ 0.504654] rtc_cmos 00:04: setting system clock to 2015-01-28 17:49:52 UTC (1422467392)
[ 0.504691] Initializing network drop monitor service
[ 0.505928] Freeing unused kernel memory: 576k freed
[ 0.506101] Write protecting the kernel read-only data: 6144k
[ 0.508528] Freeing unused kernel memory: 644k freed
[ 0.511259] Freeing unused kernel memory: 688k freed
[ 0.524103] udevd[49]: starting version 175
[ 0.525103] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.557953] SCSI subsystem initialized
[ 0.569941] libata version 3.00 loaded.
[ 0.570390] ata_piix 0000:00:1f.2: version 2.13
[ 0.570423] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 0.570469] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.579563] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 0.579625] r8169 0000:02:00.0: setting latency timer to 64
[ 0.579705] r8169 0000:02:00.0: irq 42 for MSI/MSI-X
[ 0.579833] scsi0 : ata_piix
[ 0.580371] r8169 0000:02:00.0: eth0: RTL8101e at 0xffffc9000063e000, 00:21:85:c2:87:32, XID 94200000 IRQ 42
[ 0.587473] scsi1 : ata_piix
[ 0.588096] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
[ 0.588100] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
[ 0.764152] ata1.00: ATA-8: WDC WD3200AAJS-65B4A0, 01.03A01, max UDMA/133
[ 0.764159] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.764170] ata1.01: ATAPI: Optiarc DVD RW AD-7201S6, 1H9K, max UDMA/100
[ 0.780153] ata1.00: configured for UDMA/133
[ 0.796148] ata1.01: configured for UDMA/100
[ 0.796881] scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAJS-6 01.0 PQ: 0 ANSI: 5
[ 0.798800] scsi 0:0:1:0: CD-ROM Optiarc DVD RW AD-7201S6 1H9K PQ: 0 ANSI: 5
[ 0.805914] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 0.805922] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 0.805929] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 0.806028] sd 0:0:0:0: [sda] Write Protect is off
[ 0.806034] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.806073] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[ 0.806127] sr 0:0:1:0: Attached scsi CD-ROM sr0
[ 0.859618] sda: sda1 sda2 < sda5 >
[ 0.860048] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.862292] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.862359] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 1.302335] PM: Starting manual resume from disk
[ 1.302339] PM: Hibernation image partition 8:5 present
[ 1.302340] PM: Looking for hibernation image.
[ 1.302598] PM: Image not found (code -22)
[ 1.302601] PM: Hibernation image not present or could not be loaded.
[ 1.375568] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 1.440032] Refined TSC clocksource calibration: 2394.311 MHz.
[ 1.440041] Switching to clocksource tsc
[ 3.277163] udevd[306]: starting version 175
[ 3.880086] coretemp coretemp.0: Using relative temperature scale!
[ 3.880103] coretemp coretemp.0: Using relative temperature scale!
[ 3.881741] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 3.881748] ACPI: Power Button [PWRB]
[ 3.881822] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 3.881826] ACPI: Power Button [PWRF]
[ 4.133067] ACPI: Requesting acpi_cpufreq
[ 4.406526] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 4.406564] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 4.428706] [drm] Initialized drm 1.1.0 20060810
[ 4.491027] wmi: Mapper loaded
[ 4.507907] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 4.534750] nouveau 0000:01:00.0: setting latency timer to 64
[ 4.534770] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x298000a2)
[ 4.536384] [drm] nouveau 0000:01:00.0: Checking PRAMIN for VBIOS
[ 4.580432] [drm] nouveau 0000:01:00.0: … appears to be valid
[ 4.580435] [drm] nouveau 0000:01:00.0: Using VBIOS from PRAMIN
[ 4.580439] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 4.580442] [drm] nouveau 0000:01:00.0: Bios version 62.98.29.00
[ 4.580445] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[ 4.580707] [drm] nouveau 0000:01:00.0: MXM: no VBIOS data, nothing to do
[ 4.580709] [drm] nouveau 0000:01:00.0: DCB version 4.0
[ 4.580712] [drm] nouveau 0000:01:00.0: DCB outp 00: 02000300 00000028
[ 4.580715] [drm] nouveau 0000:01:00.0: DCB outp 01: 01000302 00020030
[ 4.580717] [drm] nouveau 0000:01:00.0: DCB outp 02: 02011312 00020010
[ 4.580719] [drm] nouveau 0000:01:00.0: DCB conn 00: 00002030
[ 4.580721] [drm] nouveau 0000:01:00.0: DCB conn 01: 00001161
[ 4.580723] [drm] nouveau 0000:01:00.0: DCB conn 02: 00000362
[ 4.580728] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD40E
[ 4.605819] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xD785
[ 4.612114] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xE02B
[ 4.612122] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xE11D
[ 4.613182] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xE2F9
[ 4.613184] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xE35E
[ 4.633030] [drm] nouveau 0000:01:00.0: 0xE35E: Condition still not met after 20ms, skipping following opcodes
[ 4.633059] intel_rng: FWH not detected
[ 4.635292] [TTM] Zone kernel: Available graphics memory: 1546870 kiB
[ 4.635294] [TTM] Initializing pool allocator
[ 4.635299] [TTM] Initializing DMA pool allocator
[ 4.635310] [drm] nouveau 0000:01:00.0: Detected 256MiB VRAM (DDR2)
[ 4.635903] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 4.647817] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 4.647819] [drm] No driver support for vblank timestamp query.
[ 4.687117] hda_codec: ALC662 rev1: SKU not ready 0x411111f0
[ 4.689206] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
[ 4.693475] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 4.723227] iTCO_vendor_support: vendor-support=0
[ 4.734908] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 4.735017] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0460)
[ 4.735699] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.842938] leds_ss4200: no LED devices found
[ 4.964074] [drm] nouveau 0000:01:00.0: 1 available performance level(s)
[ 4.964079] [drm] nouveau 0000:01:00.0: 3: core 540MHz shader 1300MHz memory 500MHz fanspeed 100%
[ 4.964083] [drm] nouveau 0000:01:00.0: c: core 540MHz shader 1300MHz memory 499MHz fanspeed 30%
[ 5.026515] [drm] nouveau 0000:01:00.0: allocated 1680x1050 fb: 0x310000, bo ffff8800377d6000
[ 5.026600] fbcon: nouveaufb (fb0) is primary device
[ 5.049148] Console: switching to colour frame buffer device 210x65
[ 5.051182] fb0: nouveaufb frame buffer device
[ 5.051184] drm: registered panic notifier
[ 5.051190] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 0
[ 5.203821] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input6
[ 7.359394] Adding 6286332k swap on /dev/sda5. Priority:-1 extents:1 across:6286332k
[ 7.385530] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 7.683981] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 7.858696] loop: module loaded
[ 7.949998] f71882fg: Found f71882fg chip at 0x290, revision 32
[ 7.950125] f71882fg f71882fg.656: Fan: 1 is in duty-cycle mode
[ 7.950145] f71882fg f71882fg.656: Fan: 2 is in duty-cycle mode
[ 7.950165] f71882fg f71882fg.656: Fan: 3 is in duty-cycle mode
[ 7.950185] f71882fg f71882fg.656: Fan: 4 is in duty-cycle mode
[ 9.453739] RPC: Registered named UNIX socket transport module.
[ 9.453743] RPC: Registered udp transport module.
[ 9.453744] RPC: Registered tcp transport module.
[ 9.453746] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 9.505530] FS-Cache: Loaded
[ 9.559916] FS-Cache: Netfs ‘nfs’ registered for caching
[ 9.576291] Installing knfsd (copyright © 1996 okir@monad.swb.de).
[ 13.809844] Bluetooth: Core ver 2.16
[ 13.809876] NET: Registered protocol family 31
[ 13.809878] Bluetooth: HCI device and connection manager initialized
[ 13.809882] Bluetooth: HCI socket layer initialized
[ 13.809885] Bluetooth: L2CAP socket layer initialized
[ 13.809892] Bluetooth: SCO socket layer initialized
[ 13.840297] Bluetooth: RFCOMM TTY layer initialized
[ 13.840302] Bluetooth: RFCOMM socket layer initialized
[ 13.840304] Bluetooth: RFCOMM ver 1.11
[ 13.906146] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.906149] Bluetooth: BNEP filters: protocol multicast
[ 14.803158] r8169 0000:02:00.0: eth0: link down
[ 14.803169] r8169 0000:02:00.0: eth0: link down
[ 14.803974] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.999144] lp: driver loaded but no devices found
[ 15.019800] ppdev: user-space parallel port driver
[ 16.556289] r8169 0000:02:00.0: eth0: link up
[ 16.557077] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.416018] eth0: no IPv6 routers present
[ 50.870239] colord-sane[3684]: segfault at 0 ip 00007f3ac9302294 sp 00007fff4f9a1fb0 error 4 in libc-2.13.so[7f3ac925a000+182000]
[ 1179.973738] PM: Syncing filesystems … done.
[ 1179.978662] PM: Preparing system for mem sleep
[ 1180.044059] Freezing user space processes … (elapsed 0.01 seconds) done.
[ 1180.060114] Freezing remaining freezable tasks … (elapsed 0.01 seconds) done.
[ 1180.076042] PM: Entering mem sleep
[ 1180.076107] Suspending console(s) (use no_console_suspend to debug)
[ 1180.076439] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 1180.076644] sd 0:0:0:0: [sda] Stopping disk
[ 1180.116439] [drm] nouveau 0000:01:00.0: Disabling display…
[ 1180.117324] r8169 0000:02:00.0: eth0: link down
[ 1180.174109] [drm] nouveau 0000:01:00.0: Disabling fbcon…
[ 1180.174117] [drm] nouveau 0000:01:00.0: Unpinning framebuffer(s)…
[ 1180.174158] [drm] nouveau 0000:01:00.0: Evicting buffers…
[ 1180.506867] [drm] nouveau 0000:01:00.0: Idling channels…
[ 1180.507005] [drm] nouveau 0000:01:00.0: Suspending GPU objects…
[ 1181.725016] [drm] nouveau 0000:01:00.0: And we’re gone!
[ 1181.740105] PM: suspend of devices complete after 1663.760 msecs
[ 1181.740350] pcieport 0000:00:1c.0: wake-up capability enabled by ACPI
[ 1181.756141] PM: late suspend of devices complete after 16.029 msecs
[ 1181.756364] ACPI: Preparing to enter system sleep state S3
[ 1181.756708] PM: Saving platform NVS memory
[ 1181.757095] Disabling non-boot CPUs …
[ 1181.860090] CPU 1 is now offline
[ 1181.860606] ACPI: Low-level resume complete
[ 1181.860606] PM: Restoring platform NVS memory
[ 1181.860606] Enabling non-boot CPUs …
[ 1181.860606] Booting Node 0 Processor 1 APIC 0x1
[ 1181.860606] smpboot cpu 1: start_ip = 9a000
[ 1181.758374] Calibrating delay loop (skipped) already calibrated this CPU
[ 1181.892236] NMI watchdog enabled, takes one hw-pmu counter.
[ 1181.896069] CPU1 is up
[ 1181.897026] ACPI: Waking up from system sleep state S3
[ 1181.912340] PM: early resume of devices complete after 15.061 msecs
[ 1181.912399] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 1181.912439] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X
[ 1181.912457] pci 0000:00:1e.0: setting latency timer to 64
[ 1181.912472] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1181.912491] [drm] nouveau 0000:01:00.0: We’re back, enabling device…
[ 1181.912500] nouveau 0000:01:00.0: setting latency timer to 64
[ 1181.912505] [drm] nouveau 0000:01:00.0: POSTing device…
[ 1181.912508] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD40E
[ 1181.913025] pcieport 0000:00:1c.0: wake-up capability disabled by ACPI
[ 1181.914439] sd 0:0:0:0: [sda] Starting disk
[ 1181.937761] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xD785
[ 1181.938634] r8169 0000:02:00.0: eth0: link down
[ 1181.944059] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xE02B
[ 1181.944085] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xE11D
[ 1181.945158] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xE2F9
[ 1181.945160] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xE35E
[ 1181.965051] [drm] nouveau 0000:01:00.0: Restoring GPU objects…
[ 1182.097582] [drm] nouveau 0000:01:00.0: Reinitialising engines…
[ 1182.097857] [drm] nouveau 0000:01:00.0: Restoring mode…
[ 1183.690365] r8169 0000:02:00.0: eth0: link up
[ 1186.952026] ata1: link is slow to respond, please be patient (ready=0)
[ 1187.452153] ata1.01: ACPI cmd ef/03:45:00:00:00:b0 (SET FEATURES) filtered out
[ 1187.452160] ata1.01: ACPI cmd ef/03:45:00:00:00:b0 (SET FEATURES) filtered out
[ 1187.452165] ata1.01: ACPI cmd ef/03:0c:00:00:00:b0 (SET FEATURES) filtered out
[ 1187.452171] ata1.01: ACPI cmd f5/00:00:00:00:00:b0 (SECURITY FREEZE LOCK) filtered out
[ 1187.460152] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1187.460159] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out
[ 1187.460164] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 1187.460170] ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 1187.476157] ata1.00: configured for UDMA/133
[ 1187.492152] ata1.01: configured for UDMA/100
[ 1187.524613] PM: resume of devices complete after 5612.248 msecs
[ 1187.524839] PM: Finishing wakeup.
[ 1187.524840] Restarting tasks … done.
[/quote]

je suis sur un ordi de bureau et pour régler les paramètres en graphique je n’ai que “paramètres système” puis “énergie” et j’ai mis “ne jamais mettre en veille”… je suis dubitatif… d’autant que mes ventilos se mettent toujours à fond au démarrage puis tournent normalement après le redémarrage intempestif

[Zbf]

Donc vers 1180, c’est la mise en veille automatique qui s’est produite…
Et effectivement, il semble s’en éveiller aussitôt.

Risqué d’affirmer ça mais ça ressemble à un bug de l’ACPI.

A quand remonte la dernière mise à jour de ton système ?

[Cluxter]

2) mes ventilos tournent à fond au démarrage mais lorsque l’ordi redémarre intempestivement ils tournent au minimum. J’ai réglé fancontrol mais sans succès… j’ai dépoussiéré tout l’intérieur et laissé le capot ouvert.

Ca peut venir d’un problème de pâte thermique qui est trop vieille. De quand date l’installation (ou l’achat si tu l’as acheté déjà monté) de l’ensemble carte-mère + processeur ?

[deepo93]

bonjour et merci pour vos retours,

la dernière mise à jour je l’ai faite la semaine dernière. Je n’ai pas repéré quand ce problème a commencé en tout cas au début de l’install debian ça ne le faisait pas, ça a commencé il a quelques mois.

Sinon pour la date du PC il a 8 ans… est ce que ça pourrait correspondre à l’usure de la pâte? et si c’est le cas il y a t-il une solution pas trop compliqué car je ne suis pas le roi de la bricole (dixit ma femme:))?
De plus je m’interroge toujours sur le pourquoi ils tournent à fond seulement au début…

[Cluxter]

Sinon pour la date du PC il a 8 ans… est ce que ça pourrait correspondre à l’usure de la pâte? et si c’est le cas il y a t-il une solution pas trop compliqué car je ne suis pas le roi de la bricole (dixit ma femme:))?

Une pâte thermique tient 2 à 3 ans, à partir de 5 ans elle ne sert plus vraiment à grand-chose. J’ai refait celle de mon ordi portable la semaine dernière, il a 6 ans et j’avais ce problème depuis sa 4ème année. Depuis que je l’ai refaite ça tourne impec !

La solution pas trop compliquée c’est de demander à quelqu’un qui l’a déjà fait de te refaire la pâte thermique. Autre solution pas trop compliquée (ça dépend pour qui) : acheter un nouveau PC.

Mais j’ai envie de te dire : n’écoute pas ta femme Comment veux-tu devenir le roi de la bricole si tu n’essaies jamais ?? Voici le lien que j’ai utilisé :

forum-des-portables-asus.fr/ … -gpu.9694/

Il suffit de prendre son temps et de ne pas s’énerver.

De plus je m’interroge toujours sur le pourquoi ils tournent à fond seulement au début…

Ca c’est normal, c’est ton BIOS qui est programmé comme ça. J’imagine que ça fait partie de l’ensemble des tests qu’il effectue pour s’assurer que tout le matériel vital est bien reconnu. Ou alors c’est peut être une sécurité, car lorsque tu lances l’ordi le processeur se met à fonctionner (donc à chauffer) immédiatement, tandis que le ventilateur a une certaine inertie, donc c’est peut être juste au cas où, je ne sais pas. Mais ce qui est sûr c’est que c’est normal et que ça vient de ton BIOS. C’est d’ailleurs ce qui explique pourquoi lorsque tu redémarres les ventilos ne soufflent pas à fond : comme ton ordi est déjà allumé, les tests ont déjà été effectués par le BIOS et donc il garde ça en mémoire (jusqu’à ce que tu l’arrêtes complètement) et ne refait pas les tests.

[deepo93]

bon et bien plus qu’à me lancer.
je vais essayer de regarder tout ça la semaine prochaine.

Un grand merci en tout cas pour vos avis et conseils!.

[Zbf]

Pour la mise à jour, tu es sous Wheezy ?

[Cluxter]

Voici la pâte thermique que j’utilise :

amazon.fr/noctua-NT-H1-Noctu … B00117OV56

J’avais passé du temps à comparer lesquelles existaient, quelles étaient leurs propriétés (plus ou moins grasses, etc., je m’étais pas mal renseigné) et celle-la était celle qui était globalement classée 2ème partout, alors que d’autres étaient parfois 1ère pour certaines tâches mais 3ème ou moins pour d’autres. Donc celle-la est parfaite pour un ordi classique ou même pour un très bon ordi, c’est celle qui est le plus à même de donner de bonnes performances dans à peu près toutes les circonstances.

Si tu as des besoins très précis comme du gaming, du calcul intensif, ou si c’est juste pour pousser ton overclocking au max, il faudra t’intéresser en détail à chaque pâte et tu ne prendras pas la même selon le besoin et selon le matériel. Mais celle-la est largement suffisante pour tous les besoins courants.

[deepo93]

@Zbf: oui sous wheezy

@Cluxter: j’ai une utilisation très classique de mon ordi, juste internet, vidéos, films et un peu de traitement de texte. Rien d’exceptionnel donc je pense rester dans la pâte à tout faire )