[RESOLU] WEBCAM éteinte Phillips après update et upgrade

Je suis si peu clair que ça ??? :question: :question: :smiling_imp:

a la place de ton apt-get install linux-headers-`uname -r` essaye un m-a prepare comme ca plus de probleme si il fonctionne correctement

Si tu regarde la sortie de ton apt-get install linux-headers-`uname -r`Tu verras qu’il n’a rien installé donc pas la peine de continuer

Et je pense que tu devrais pouvoir t’en sortir avec module-assistant pour la suite.

Non, mais ton message était vide, je regarde…

Essaye

boisson.homeip.net/gspca-2.6.18-3-68.ko

Non tu es très clair cher pingoin !

deb:/lib/modules/2.6.18-3-686/misc# mv gspca-2.6.18-3-68.ko gspca.ko deb:/lib/modules/2.6.18-3-686/misc# ls
gspca.ko quickcam.ko
deb:/lib/modules/2.6.18-3-686/misc# depmod -ae
deb:/lib/modules/2.6.18-3-686/misc# modprobe gspca
FATAL: Error inserting gspca (/lib/modules/2.6.18-3-686/misc/gspca.ko): Unknown symbol in module, or unknown parameter (see dmesg)

La même en couleur apparemment :
deb:/lib/modules/2.6.18-3-686/misc# dmesg
Linux version 2.6.18-3-686 (Debian 2.6.18-7) (waldi@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 SMP Mon Dec 4 16:41:14 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002dfb0000 (usable)
BIOS-e820: 000000002dfb0000 - 000000002dfc0000 (ACPI data)
BIOS-e820: 000000002dfc0000 - 000000002dff0000 (ACPI NVS)
BIOS-e820: 000000002dff0000 - 000000002e000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
735MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 188336
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 184240 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000fac80
ACPI: RSDT (v001 A M I OEMRSDT 0x06000524 MSFT 0x00000097) @ 0x2dfb0000
ACPI: FADT (v002 A M I OEMFACP 0x06000524 MSFT 0x00000097) @ 0x2dfb0200
ACPI: MADT (v001 A M I OEMAPIC 0x06000524 MSFT 0x00000097) @ 0x2dfb0390
ACPI: OEMB (v001 A M I AMI_OEM 0x06000524 MSFT 0x00000097) @ 0x2dfc0040
ACPI: DSDT (v001 P4V80 P4V80000 0x00000000 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 2e000000:d1780000)
Detected 2533.795 MHz processor.
Built 1 zonelists. Total pages: 188336
Kernel command line: root=/dev/hda1 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 739000k/753344k available (1543k kernel code, 13768k reserved, 574k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay using timer specific routine… 5073.81 BogoMIPS (lpj=10147636)Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000180 0000441d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking ‘hlt’ instruction… OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
CPU0: Intel® Celeron® CPU 2.53GHz stepping 01
Total of 1 processors activated (5073.81 BogoMIPS).
ENABLING IO-APIC IRQs
…TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs… it is
Freeing initrd memory: 4404k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PRT]
ACPI: PCI Interrupt Routing Table [_SB
.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 © Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try “pci=routeirq”. If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fca00000-feafffff
PREFETCH window: eff00000-f7efffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1172776236.892:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0f03:PS2M] at 0x60,0x64 irq 12
PNP: PS/2 controller doesn’t have KBD irq; using default 1
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
Time: tsc clocksource has been installed.
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 196k freed
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.0, from 10 to 9
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 169, io base 0x0000c000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.1, from 10 to 9
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 169, io base 0x0000c400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.2, from 11 to 9
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 169, io base 0x0000c800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:10.3, from 11 to 9
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 169, io base 0x0000cc00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) -> IRQ 177
eth0: VIA Rhine II at 0x1d400, 00:13:8f:22:a0:aa, IRQ 177.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
sata_via 0000:00:0f.0: version 2.0
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 185
sata_via 0000:00:0f.0: routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 185
ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 185
scsi0 : sata_via
ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xEC07
scsi1 : sata_via
usb 2-2: new low speed USB device using uhci_hcd and address 2
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xE407
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 185
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0…
usb 2-2: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
hda: HDS728080PLAT20, ATA DISK drive
usb 3-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver…
usbcore: registered new driver hiddev
input: USB Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:10.1-2
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1…
input: USB Keyboard as /class/input/input1
input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:10.1-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
hdc: TSSTcorpCD/DVDW SH-W162C, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 160836480 sectors (82348 MB) w/1719KiB Cache, CHS=16383/255/63, UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdc: ATAPI 94X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input2
Linux agpgart interface v0.101 © Dave Jones
agpgart: Detected VIA P4M800CE chipset
agpgart: AGP aperture is 64M @ 0xf8000000
Vendor: Generic Model: 2.0 Reader-CF Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Generic Model: 2.0 Reader-SM/xD Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Generic Model: 2.0 Reader-SD Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Generic Model: 2.0 Reader-MS Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 00
Linux video capture interface: v2.00
usb-storage: device scan complete
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
FDC 0 is a post-1991 82077
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 193
saa7133[0]: found at 0000:00:09.0, rev: 208, irq: 193, latency: 32, mmio: 0xfebff000
saa7133[0]: subsystem: 1043:4862, board: ASUSTeK P7131 Dual [card=78,autodetected]
saa7133[0]: board init: gpio is 0
saa7133[0]: gpio: mode=0x0000000 in=0x0000000 out=0x0000000 [pre-init]
input: saa7134 IR (ASUSTeK P7131 Dual) as /class/input/input4
Real Time Clock Driver v1.12ac
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
sd 2:0:0:0: Attached scsi removable disk sda
sd 2:0:0:1: Attached scsi removable disk sdb
saa7133[0]: i2c eeprom 00: 43 10 62 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: 00 01 20 00 ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d6 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 00 ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
sd 2:0:0:2: Attached scsi removable disk sdc
sd 2:0:0:3: Attached scsi removable disk sdd
ts: Compaq touchscreen protocol output
tuner 1-004b: chip found @ 0x96 (saa7133[0])
tuner 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:11.5 to 64
Adding 650592k swap on /dev/hda5. Priority:-1 extents:1 across:650592k
EXT3 FS on hda1, internal journal
DVB: registering new adapter (saa7133[0]).
DVB: registering frontend 0 (Philips TDA10046H DVB-T)…
quickcam: disagrees about version of symbol video_devdata
quickcam: Unknown symbol video_devdata
quickcam: disagrees about version of symbol video_unregister_device
quickcam: Unknown symbol video_unregister_device
quickcam: disagrees about version of symbol video_register_device
quickcam: Unknown symbol video_register_device
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
apm: overridden by ACPI.
eth0: no IPv6 routers present
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
gspca: disagrees about version of symbol video_devdata
gspca: Unknown symbol video_devdata
gspca: disagrees about version of symbol video_unregister_device
gspca: Unknown symbol video_unregister_device
gspca: disagrees about version of symbol video_device_alloc
gspca: Unknown symbol video_device_alloc
gspca: disagrees about version of symbol video_register_device
gspca: Unknown symbol video_register_device
gspca: disagrees about version of symbol video_device_release
gspca: Unknown symbol video_device_release

Toutes ces fonctions sont définies dans videodev.ko

Que donnes lsmod après le modprobe, essaye de forcer le chargement de videodev avant

modprobe videodev

deb:/home/fr# modprobe videodev
deb:/home/fr# depmod -ae
deb:/home/fr# modprobe gspca
FATAL: Error inserting gspca (/lib/modules/2.6.18-3-686/misc/gspca.ko): Unknown symbol in module, or unknown parameter (see dmesg)
deb:/home/fr# lsmod
Module Size Used by
nls_iso8859_1 4256 1
isofs 32540 1
udf 73156 0
button 6672 0
ac 5188 0
battery 9636 0
autofs4 19748 0
ipv6 226016 8
sd_mod 19040 0
dm_snapshot 15520 0
dm_mirror 19152 0
dm_mod 50232 2 dm_snapshot,dm_mirror
saa7134_dvb 18472 0
dvb_pll 13956 1 saa7134_dvb
video_buf_dvb 6404 1 saa7134_dvb
dvb_core 71464 1 video_buf_dvb
tda1004x 13348 2 saa7134_dvb
firmware_class 9600 2 saa7134_dvb,tda1004x
ide_generic 1408 0 [permanent]
snd_seq_dummy 3844 0
snd_seq_oss 28768 0
snd_seq_midi 8192 0
snd_seq_midi_event 7008 2 snd_seq_oss,snd_seq_midi
snd_seq 45680 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
tsdev 7520 0
snd_via82xx 26008 1
gameport 14632 1 snd_via82xx
snd_ac97_codec 83104 1 snd_via82xx
snd_ac97_bus 2400 1 snd_ac97_codec
evdev 9088 3
tuner 53064 0
snd_pcm_oss 38368 1
snd_mixer_oss 15200 1 snd_pcm_oss
snd_pcm 68644 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_timer 20996 2 snd_seq,snd_pcm
snd_page_alloc 9640 2 snd_via82xx,snd_pcm
snd_mpu401_uart 8064 1 snd_via82xx
snd_rawmidi 22560 2 snd_seq_midi,snd_mpu401_uart
snd_seq_device 7820 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
saa7134 115296 1 saa7134_dvb
video_buf 22820 3 saa7134_dvb,video_buf_dvb,saa7134
compat_ioctl32 1312 1 saa7134
ir_kbd_i2c 8432 1 saa7134
snd 47012 11 snd_seq_oss,snd_seq,snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
pcspkr 3072 0
ir_common 33892 2 saa7134,ir_kbd_i2c
psmouse 35016 0
usbhid 37248 0
usb_storage 71840 0
floppy 53156 0
videodev 24320 1 saa7134
v4l2_common 14816 3 tuner,saa7134,videodev
v4l1_compat 12196 2 saa7134,videodev
via_agp 9664 1
agpgart 29896 1 via_agp
serio_raw 6660 0
parport_pc 32164 0
parport 33256 1 parport_pc
soundcore 9248 2 snd
rtc 12372 0
i2c_viapro 8148 0
i2c_core 19680 7 saa7134_dvb,dvb_pll,tda1004x,tuner,saa7134,ir_kbd_i2c,i2c_viapro
shpchp 33024 0
pci_hotplug 28704 1 shpchp
ext3 119208 1
jbd 52456 1 ext3
mbcache 8356 1 ext3
ide_cd 36064 1
cdrom 32544 1 ide_cd
ide_disk 14848 3
via_rhine 22664 0
mii 5344 1 via_rhine
uhci_hcd 21032 0
via82cxxx 8388 0 [permanent]
usbcore 112676 4 usbhid,usb_storage,uhci_hcd
sata_via 10052 0
generic 5028 0 [permanent]
ide_core 110504 6 ide_generic,usb_storage,ide_cd,ide_disk,via82cxxx,generic
libata 89332 1 sata_via
scsi_mod 124168 3 sd_mod,usb_storage,libata
thermal 13608 0
processor 28840 1 thermal
fan 4804 0

Bon, donne moi le résultat de

$ COLUMNS=132 dpkg -l | grep linux

Il y a un problème avec ton noyau…

Cela donne :

deb:/home/fr# COLUMNS=132 dpkg -l | grep linux
ii doc-linux-fr-text 2005.08-1 Linux docs in French: HOWTOs, MetaFAQs in ASCII format
ii doc-linux-text 2006.12-1 Linux HOWTOs and FAQs in ASCII format
ii libselinux1 1.32-3 SELinux shared libraries
ii linux-headers-2.6.18-3 2.6.18-7 Common header files for Linux 2.6.18
ii linux-headers-2.6.18-3-686 2.6.18-7 Header files for Linux 2.6.18 on PPro/Celeron/PII/PIII/P4
ii linux-image-2.6-686 2.6.18+5 Linux kernel 2.6 image on PPro/Celeron/PII/PIII/P4
ii linux-image-2.6.15-1-686 2.6.15-8 Linux kernel 2.6.15 image on PPro/Celeron/PII/PIII/P4 machines
ii linux-image-2.6.15.060620 2.6.15-8 Linux kernel binary image for version 2.6.15.060620
ii linux-image-2.6.15.060630 2.6.15-8 Linux kernel binary image for version 2.6.15.060630
ii linux-image-2.6.15.060705 2.6.15-8 Linux kernel binary image for version 2.6.15.060705
ii linux-image-2.6.16-2-686 2.6.16-18 Linux kernel 2.6.16 image on PPro/Celeron/PII/PIII/P4 machines
ii linux-image-2.6.17-2-686 2.6.17-9 Linux 2.6.17 image on PPro/Celeron/PII/PIII/P4
ii linux-image-2.6.18-3-686 2.6.18-7 Linux 2.6.18 image on PPro/Celeron/PII/PIII/P4
ii linux-kbuild-2.6.18 2.6.18-1 Kbuild infrastructure for Linux 2.6.18
ii linux-kernel-headers 2.6.18-7 Linux Kernel Headers for development
ii linux-patch-debian-2.6.15 2.6.15-8 Debian patches to version 2.6.15 of the Linux kernel
ii linux-sound-base 1.0.13-4 base package for ALSA and OSS sound systems
ii linux-source-2.6.15 2.6.15-8 Linux kernel source for version 2.6.15 with Debian patches
ii util-linux 2.12r-16 Miscellaneous system utilities
ii v4l-conf 3.95.dfsg.1-1 tool to configure video4linux drivers

Pour info, voilà la où j’ai fait le module:

[quote]ii linux-headers-2.6.18-3 2.6.18-7 Common header files for Linux 2.6.18
ii linux-headers-2.6.18-3-686 2.6.18-7 Header files for Linux 2.6.18 on PPro/Celeron/PII/PIII/P4
ii linux-image-2.6.18-3-686 2.6.18-7 Linux 2.6.18 image on PPro/Celeron/PII/PIII/P4
ii linux-kbuild-2.6.18 2.6.18-1 Kbuild infrastructure for Linux 2.6.18
ii linux-kernel-headers 2.6.18-6 Linux Kernel Headers for development
[/quote]

C’est le même noyau, or moi le module est bien chargé…

Bizarre vraiment, compare

$ md5sum /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
7c939b807ca84c7e6838b29a1f69edad  /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
/boot
$ ls -l /boot/vmlinuz-2.6.18-3-686
-rw-r--r-- 1 root root 1259920 2006-12-04 23:24 /boot/vmlinuz-2.6.18-3-686
/boot
$ md5sum /boot/vmlinuz-2.6.18-3-686
b25f3bd335eefc766d65b808500df9ec  /boot/vmlinuz-2.6.18-3-686
/boot
$ 

deb:/home/fr# md5sum /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
c2d2d1ffb32dc3945d30aa1025508090 /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko

deb:/home/fr# ls -l /boot/vmlinuz-2.6.18-3-686
-rw-r–r-- 1 root root 1259920 2006-12-04 23:24 /boot/vmlinuz-2.6.18-3-686

deb:/home/fr# md5sum /boot/vmlinuz-2.6.18-3-686
b25f3bd335eefc766d65b808500df9ec /boot/vmlinuz-2.6.18-3-686

Est-ce que quelqu’un peut se mettre à mon niveau ?
Je comprends pas où est le problème.
:blush:

[quote]deb:/home/fr# md5sum /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
c2d2d1ffb32dc3945d30aa1025508090 /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko

deb:/home/fr# ls -l /boot/vmlinuz-2.6.18-3-686
-rw-r–r-- 1 root root 1259920 2006-12-04 23:24 /boot/vmlinuz-2.6.18-3-686

deb:/home/fr# md5sum /boot/vmlinuz-2.6.18-3-686
b25f3bd335eefc766d65b808500df9ec /boot/vmlinuz-2.6.18-3-686
[/quote]
pour toi et

[quote]$ md5sum /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
7c939b807ca84c7e6838b29a1f69edad /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
/boot
$ ls -l /boot/vmlinuz-2.6.18-3-686
-rw-r–r-- 1 root root 1259920 2006-12-04 23:24 /boot/vmlinuz-2.6.18-3-686
/boot
$ md5sum /boot/vmlinuz-2.6.18-3-686
b25f3bd335eefc766d65b808500df9ec /boot/vmlinuz-2.6.18-3-686
/boot
$
[/quote]C’est le même noyau mais pas le même videodev.ko. Comme je le pensais, ton module videodev est défectueux. Réinstalle ton noyau ou mieux, charges le videodev sur
http://boisson.homeip.net/sarge/videodev-2.6.18-3-686.ko
(Dsl: je n’avais pas vu ta réponse)

c’est fait:

deb:/home/fr# mv videodev-2.6.18-3-686.ko /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
deb:/home/fr# depmod -ae deb:/home/fr# modprobe gspca FATAL: Error inserting gspca (/lib/modules/2.6.18-3-686/misc/gspca.ko): Unknownsymbol in module, or unknown parameter (see dmesg)
deb:/home/fr# md5sum /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
7c939b807ca84c7e6838b29a1f69edad /lib/modules/2.6.18-3-686/kernel/drivers/media/video/videodev.ko
deb:/home/fr# ls -l /boot/vmlinuz-2.6.18-3-686
-rw-r–r-- 1 root root 1259920 2006-12-04 23:24 /boot/vmlinuz-2.6.18-3-686

quoi d’autres?

Bon, brutal:

récupère http://boisson.homeip.net/sarge/modules2.6.18-3.tgz

et fait

cd /lib/modules

tar xzf /modules2.6.18-3.tgz

depmod -ae

oups !!
deb:/home/fr# cd /lib/modules
deb:/lib/modules# tar xzf /home/fr/modules2.6.18-3.tgz

gzip: stdin: unexpected end of file
tar: Fin prématurée (EOF) rencontrée dans l’archive.
tar: Fin prématurée (EOF) rencontrée dans l’archive.
tar: Erreur non récupérable: fin de l’exécution immédiate

en ajoutant v dans tar

gzip: stdin: unexpected end of file
2.6.18-3-686/kernel/net/sched/sch_hfsc.ko
tar: Fin prématurée (EOF) rencontrée dans l’archive.
tar: Fin prématurée (EOF) rencontrée dans l’archive.
tar: Erreur non récupérable: fin de l’exécution immédiate
deb:/lib/modules# depmode -ae
bash: depmode: command not found
deb:/lib/modules# depmode-ae
bash: depmode-ae: command not found
deb:/lib/modules# depmod-ae
bash: depmod-ae: command not found
deb:/lib/modules# depmod -ae
WARNING: Couldn’t find symtab and strtab in module /lib/modules/2.6.18-3-686/kernel/net/sched/sch_hfsc.ko

A n’y rien comprendre j’ai refais la marche à suivre et finalement ta commande fonctionne sans message d’erreur cette fois!
Ensuite ?
demod -ae
modprobe gspca renvoie toujours pareil

Reboutes la machine, ça devrait marcher.

C’est carré merci beaucoup.

Je te dis pas à bientôt (j’espère que les modifs que tu as faites pour adapter le driver seront un jour dans les releases).
:smiley: