Clef pas detcetée

Support Debian
#1

Bonjour
Je ne réussi plis à voir mes clés et mes disques externes liés en usb
Mais les portes usb sont detcetées:

[quote]sudo lsusb
[sudo] password for carlos:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0ac8:3450 Z-Star Microelectronics Corp.
Bus 001 Device 003: ID 0bc2:0503 Seagate RSS LLC
Bus 001 Device 004: ID 04b8:011f Seiko Epson Corp. Perfection 1670
Bus 006 Device 002: ID 04f3:0234 Elan Microelectronics Corp.
Bus 003 Device 002: ID 03f0:0904 Hewlett-Packard DeskJet 845c
Bus 002 Device 002: ID 0cf2:6230 ENE Technology, Inc.
[/quote]

Une idée’

Merci

#2

As tu essayé sur différent port usb.
Sinon sa peut venir de ton controleur

#3

En gros si je comprends bien le montage des périphs USB ne se fait plus automatiquement.

  • Voir ce qui se passe dans [mono]dmesg[/mono] après branchement d’un périph.
  • Tenter de le monter manuellement: [mono]mount /dev/sdXY /mnt/UnRepertoireExistant[/mono]
#4

Merci de vos réponses
En effet, cela se montait sans problème, avant. Maintenant, non. J’ai deux portes usb3 et deux disques externes usb3, ceux -là elles les montrent, les autres non,telles que les autres portes, usb1 et usb2. Sur la net, il y a qui dise qu’il faut créer des répertoires pour les clés, et ensuite les monter, et qu’elles soient dans fstab, mais ce n’est pas bien cela, mon fichier fstab ne contenait pas des lignes pour des clés et elles étaient ouvertes avant .Qu’en pensez-vous?

#5

Il y a certains logiciels qui font ces montages automatiquement.
Gnome, KDE… tous les gros environnements ont ça.
Donc pour une raison quelconque, cet outil de montage automatique n’est plus fonctionnel chez toi.

Ces outils sont censés être une évolution par rapport à l’usage de fstab. Donc remplir fstab ce serait une régression et moins pratique pour toi.

Par contre, la source du problème n’est pas confirmée.

  • c’est pour ça que je proposais un montage manuel, pour voir si ça fonctionne et si ça n’est pas le support lui-même (donc ta clé USB) qui déconne.
  • mais je penche plutôt sur un problème avec le logiciel qui gère les montages automatiques de ton environnement.

Donc quel est cet environnement de bureau ? As-tu changé qqch dernièrement ?

#6

Bonjour. Merci.
Je suis sous kde. Mais cela se passe sous Gnome (classic)aussi. Et encore: J’ai d’autres versions de Linux installées (J’aime accompagner ce qu’on fait là-dessus) telles que Open Suse et, là aussi, il se passe le même. J’en ai aussi un vieux XP, à cause d’une base de données de l?access, et c’est la même chose: Les deux disques externes usb3 , on les voit sous les portes usb3, pas les autres.Même sur une porte où était branché mon scanner,le disque externe ne se voit pas. C’est très étrange, tout ça.

#7

Donc en gros t’es en train de dire que quel que soit le système d’exploitation, tu n’arrives pas à accéder à tes disques durs ?

C’est effectivement étrange. Sur une autre machine ces disques durs fonctionnent ?

Sous Linux, tu peux coller le résultat de [mono]dmesg[/mono] après les avoir branchés, ça donnera ptet qq indices.

#8

Bonjour
Il ne s’agit pas des disques durs internes, mais de disques externes liés à des portes usb
La commande dmesg n’est pas acceptée par ce forum, son résultat est trop grand.

#9

Donne la fin ou met la en pièce jointe. Donne plus de renseignements notamment le type de système de fichiers sur ces clefs.

#10

Ça me paraît peu probable mais est-ce qu’il ne s’agit pas d’une configuration du bios ?
En tout cas moi j’y remettrais tous les paramètres par défaut. Avec certains bios c’est proposé mais peut-être pas avec tous. Sinon y’a qu’à retirer la pile et la remettre si c’est une tour. Faut toutefois s’assurer avant qu’on a pas plusieurs disques durs internes et noter les ordres de boot.

A+

#11

En voici la dernière partie

[quote].
[ 3.485767] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
[ 4.419262] usb 1-2: New USB device found, idVendor=0bc2, idProduct=0503
[ 4.419265] usb 1-2: New USB device strings: Mfr=54, Product=69, SerialNumber=95
[ 4.419267] usb 1-2: Product: Seagate External Drive
[ 4.419269] usb 1-2: Manufacturer: Jabil Circuit
[ 4.419270] usb 1-2: SerialNumber: SW070101442
[ 4.532017] usb 1-5: new high-speed USB device number 4 using ehci_hcd
[ 4.665596] usb 1-5: New USB device found, idVendor=059b, idProduct=047a
[ 4.665599] usb 1-5: New USB device strings: Mfr=10, Product=11, SerialNumber=3
[ 4.665600] usb 1-5: Product: eGo USB
[ 4.665602] usb 1-5: Manufacturer: Iomega
[ 4.665603] usb 1-5: SerialNumber: 912000003C21
[ 4.996022] usb 6-3: new low-speed USB device number 2 using ohci_hcd
[ 5.173950] usb 6-3: New USB device found, idVendor=04f3, idProduct=0234
[ 5.173953] usb 6-3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 5.173955] usb 6-3: Product: OM
[ 5.218922] udevd[424]: starting version 175
[ 5.440020] usb 4-1: new full-speed USB device number 2 using ohci_hcd
[ 5.628950] usb 4-1: New USB device found, idVendor=03f0, idProduct=0904
[ 5.628953] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.628954] usb 4-1: Product: DeskJet 845C
[ 5.628956] usb 4-1: Manufacturer: Hewlett-Packard
[ 5.628957] usb 4-1: SerialNumber: TH18E1G8DCSX
[ 5.743546] usb 5-2: new SuperSpeed USB device number 2 using xhci_hcd
[ 5.757553] usb 5-2: New USB device found, idVendor=0951, idProduct=1666
[ 5.757556] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.757558] usb 5-2: Product: DataTraveler 3.0
[ 5.757560] usb 5-2: Manufacturer: Kingston
[ 5.757562] usb 5-2: SerialNumber: 60A44C4138D1BD91D33B4113
[ 5.842623] wmi: Mapper loaded
[ 5.970204] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 5.970209] ACPI: Power Button [PWRB]
[ 5.970253] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.970256] ACPI: Power Button [PWRF]
[ 6.313934] ACPI: acpi_idle registered with cpuidle
[ 6.330987] ATK0110 ATK0110:00: Overriding interface detection
[ 6.433715] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 6.480659] parport_pc 00:06: reported by Plug and Play ACPI
[ 6.480727] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 6.481703] hda_intel: Disabling MSI
[ 6.481722] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[ 6.645343] ACPI: resource piix4_smbus [io 0x0b00-0x0b07] conflicts with ACPI region SOR1 [io 0xb00-0xb0f]
[ 6.645345] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 6.674399] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[ 6.674455] SP5100 TCO timer: mmio address 0xfec000f0 already in use
[ 6.776105] [drm] Initialized drm 1.1.0 20060810
[ 6.808773] powernow-k8: Found 1 AMD FX™-4300 Quad-Core Processor (4 cpu cores) (version 2.20.00)
[ 6.808785] powernow-k8: Core Performance Boosting: on.
[ 6.808825] powernow-k8: 0 : pstate 0 (3800 MHz)
[ 6.808826] powernow-k8: 1 : pstate 1 (3400 MHz)
[ 6.808828] powernow-k8: 2 : pstate 2 (2600 MHz)
[ 6.808829] powernow-k8: 3 : pstate 3 (1800 MHz)
[ 6.808830] powernow-k8: 4 : pstate 4 (1400 MHz)
[ 7.057030] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x0904
[ 7.057073] usbcore: registered new interface driver usblp
[ 7.134170] input: OM as /devices/pci0000:00/0000:00:12.1/usb6/6-3/6-3:1.0/input/input4
[ 7.134486] generic-usb 0003:04F3:0234.0001: input,hidraw0: USB HID v1.11 Mouse [OM] on usb-0000:00:12.1-3/input0
[ 7.134524] usbcore: registered new interface driver usbhid
[ 7.134529] usbhid: USB HID core driver
[ 7.306483] Initializing USB Mass Storage driver…
[ 7.306742] scsi6 : usb-storage 1-2:1.0
[ 7.307086] scsi7 : usb-storage 1-5:1.0
[ 7.307315] scsi8 : usb-storage 5-2:1.0
[ 7.307454] usbcore: registered new interface driver usb-storage
[ 7.307459] USB Mass Storage support registered.
[ 7.408087] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 7.440087] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 7.472107] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 7.504036] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 7.520211] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input5
[ 7.520372] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input6
[ 7.520511] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input7
[ 7.520650] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input8
[ 7.522018] nouveau 0000:01:00.0: setting latency timer to 64
[ 7.522049] [drm] nouveau 0000:01:00.0: Detected an NV50 generation card (0x0a8280b1)
[ 7.535762] [drm] nouveau 0000:01:00.0: Checking PRAMIN for VBIOS
[ 7.612098] [drm] nouveau 0000:01:00.0: … appears to be valid
[ 7.612104] [drm] nouveau 0000:01:00.0: Using VBIOS from PRAMIN
[ 7.612111] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 7.612117] [drm] nouveau 0000:01:00.0: Bios version 70.18.5f.00
[ 7.612123] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[ 7.612444] [drm] nouveau 0000:01:00.0: MXM: no VBIOS data, nothing to do
[ 7.612446] [drm] nouveau 0000:01:00.0: DCB version 4.0
[ 7.612449] [drm] nouveau 0000:01:00.0: DCB outp 00: 01000302 00020030
[ 7.612450] [drm] nouveau 0000:01:00.0: DCB outp 01: 02000300 00000000
[ 7.612452] [drm] nouveau 0000:01:00.0: DCB outp 02: 02011362 00020010
[ 7.612453] [drm] nouveau 0000:01:00.0: DCB outp 03: 01022310 00000000
[ 7.612455] [drm] nouveau 0000:01:00.0: DCB conn 00: 00001030
[ 7.612456] [drm] nouveau 0000:01:00.0: DCB conn 01: 00002161
[ 7.612458] [drm] nouveau 0000:01:00.0: DCB conn 02: 00000200
[ 7.612462] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD97D
[ 7.672955] [drm] nouveau 0000:01:00.0: 0xDC4A: Condition still not met after 20ms, skipping following opcodes
[ 7.692801] [drm] nouveau 0000:01:00.0: 0xDC4E: Condition still not met after 20ms, skipping following opcodes
[ 7.692821] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDE28
[ 7.700520] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xE9FB
[ 7.700526] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEA14
[ 7.743021] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEAFB
[ 7.743025] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEB60
[ 7.762869] [drm] nouveau 0000:01:00.0: 0xD7F1: Condition still not met after 20ms, skipping following opcodes
[ 7.765409] [TTM] Zone kernel: Available graphics memory: 432478 kiB
[ 7.765415] [TTM] Zone highmem: Available graphics memory: 2064994 kiB
[ 7.765418] [TTM] Initializing pool allocator
[ 7.765427] [TTM] Initializing DMA pool allocator
[ 7.765443] [drm] nouveau 0000:01:00.0: Detected 1024MiB VRAM (DDR3)
[ 7.770311] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 7.803308] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.803309] [drm] No driver support for vblank timestamp query.
[ 8.120062] [drm] nouveau 0000:01:00.0: 3 available performance level(s)
[ 8.120066] [drm] nouveau 0000:01:00.0: 0: core 135MHz shader 270MHz memory 135MHz voltage 850mV
[ 8.120069] [drm] nouveau 0000:01:00.0: 1: core 405MHz shader 810MHz memory 405MHz voltage 900mV
[ 8.120071] [drm] nouveau 0000:01:00.0: 3: core 589MHz shader 1402MHz memory 600MHz voltage 1000mV
[ 8.120073] [drm] nouveau 0000:01:00.0: c: core 405MHz shader 810MHz memory 405MHz voltage 900mV
[ 8.304437] scsi 8:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6
[ 8.305454] [drm] nouveau 0000:01:00.0: allocated 1920x1080 fb: 0x310000, bo f7046800
[ 8.305514] fbcon: nouveaufb (fb0) is primary device
[ 8.305660] sd 8:0:0:0: Attached scsi generic sg5 type 0
[ 8.308163] scsi 6:0:0:0: Direct-Access Seagate External Drive PQ: 0 ANSI: 0
[ 8.308293] sd 8:0:0:0: [sde] 15360000 512-byte logical blocks: (7.86 GB/7.32 GiB)
[ 8.310560] sd 8:0:0:0: [sde] Write Protect is off
[ 8.310567] sd 8:0:0:0: [sde] Mode Sense: 2b 80 00 08
[ 8.310706] HDMI hot plug event: Codec=1 Pin=5 Presence_Detect=1 ELD_Valid=0
[ 8.311703] sd 8:0:0:0: [sde] Write cache: disabled, read cache: enabled, doesn’t support DPO or FUA
[ 8.316013] HDMI status: Codec=1 Pin=5 Presence_Detect=1 ELD_Valid=1
[ 8.319282] sde: sde1
[ 8.322549] sd 8:0:0:0: [sde] Attached SCSI removable disk
[ 8.330914] Console: switching to colour frame buffer device 240x67
[ 8.334104] fb0: nouveaufb frame buffer device
[ 8.334106] drm: registered panic notifier
[ 8.334109] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 0
[ 8.346616] scsi 7:0:0:0: Direct-Access ST950032 5AS PQ: 0 ANSI: 2 CCS
[ 8.347036] sd 7:0:0:0: Attached scsi generic sg6 type 0
[ 8.347774] sd 6:0:0:0: Attached scsi generic sg7 type 0
[ 8.348396] sd 6:0:0:0: [sdg] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 8.348424] sd 7:0:0:0: [sdf] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 8.349133] sd 7:0:0:0: [sdf] Write Protect is off
[ 8.349141] sd 7:0:0:0: [sdf] Mode Sense: 28 00 00 00
[ 8.349254] sd 6:0:0:0: [sdg] Write Protect is off
[ 8.349264] sd 6:0:0:0: [sdg] Mode Sense: 27 00 00 00
[ 8.349876] sd 7:0:0:0: [sdf] No Caching mode page found
[ 8.349902] sd 7:0:0:0: [sdf] Assuming drive cache: write through
[ 8.350129] sd 6:0:0:0: [sdg] No Caching mode page found
[ 8.350165] sd 6:0:0:0: [sdg] Assuming drive cache: write through
[ 8.359377] sd 7:0:0:0: [sdf] No Caching mode page found
[ 8.359399] sd 7:0:0:0: [sdf] Assuming drive cache: write through
[ 8.359504] sd 6:0:0:0: [sdg] No Caching mode page found
[ 8.359521] sd 6:0:0:0: [sdg] Assuming drive cache: write through
[ 8.391451] sdg: sdg1
[ 8.394372] sd 6:0:0:0: [sdg] No Caching mode page found
[ 8.394396] sd 6:0:0:0: [sdg] Assuming drive cache: write through
[ 8.394415] sd 6:0:0:0: [sdg] Attached SCSI disk
[ 8.426944] sdf: sdf1
[ 8.429627] sd 7:0:0:0: [sdf] No Caching mode page found
[ 8.429647] sd 7:0:0:0: [sdf] Assuming drive cache: write through
[ 8.429662] sd 7:0:0:0: [sdf] Attached SCSI disk
[ 9.092098] HDMI: detected monitor M237WDP at connection type HDMI
[ 9.092106] HDMI: available speakers: FL/FR LFE FC RL/RR RC FLC/FRC RLC/RRC FLW/FRW FLH/FRH TC FCH
[ 9.092114] HDMI: supports coding type AC-3: channels = 6, rates = 32000 44100 48000, max bitrate = 640000
[ 9.092122] HDMI: supports coding type LPCM: channels = 2, rates = 32000 44100 48000, bits = 16 20 24
[ 9.100096] HDMI hot plug event: Codec=1 Pin=5 Presence_Detect=1 ELD_Valid=1
[ 9.108034] HDMI status: Codec=1 Pin=5 Presence_Detect=1 ELD_Valid=1
[ 9.402075] kjournald starting. Commit interval 5 seconds
[ 9.402229] EXT3-fs (sdg1): warning: maximal mount count reached, running e2fsck is recommended
[ 9.403643] EXT3-fs (sdg1): using internal journal
[ 9.403651] EXT3-fs (sdg1): mounted filesystem with ordered data mode
[ 9.888140] HDMI: detected monitor M237WDP at connection type HDMI
[ 9.888149] HDMI: available speakers: FL/FR LFE FC RL/RR RC FLC/FRC RLC/RRC FLW/FRW FLH/FRH TC FCH
[ 9.888157] HDMI: supports coding type AC-3: channels = 6, rates = 32000 44100 48000, max bitrate = 640000
[ 9.888164] HDMI: supports coding type LPCM: channels = 2, rates = 32000 44100 48000, bits = 16 20 24
[ 13.953279] FAT-fs (sde1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 24.476531] FAT-fs (sdf1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 25.419830] Adding 4096536k swap on /dev/sdb1. Priority:-1 extents:1 across:4096536k
[ 25.445658] EXT4-fs (sdb2): re-mounted. Opts: (null)
[ 25.931691] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro
[ 26.064641] loop: module loaded
[ 27.547812] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null)
[ 27.665065] fuse init (API version 7.17)
[ 27.997073] EXT4-fs (sdc3): mounted filesystem with ordered data mode. Opts: (null)
[ 28.116026] EXT4-fs (sdc2): mounted filesystem with ordered data mode. Opts: (null)
[ 28.160926] EXT4-fs (sda3): warning: maximal mount count reached, running e2fsck is recommended
[ 28.178604] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 28.302353] kjournald starting. Commit interval 5 seconds
[ 28.302816] EXT3-fs (sdb4): using internal journal
[ 28.302823] EXT3-fs (sdb4): mounted filesystem with ordered data mode
[ 28.337594] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 29.414851] RPC: Registered named UNIX socket transport module.
[ 29.414856] RPC: Registered udp transport module.
[ 29.414859] RPC: Registered tcp transport module.
[ 29.414863] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 29.443649] FS-Cache: Loaded
[ 29.470848] FS-Cache: Netfs ‘nfs’ registered for caching
[ 29.489074] Installing knfsd (copyright © 1996 okir@monad.swb.de).
[ 29.798349] r8169 0000:03:00.0: firmware: agent aborted loading rtl_nic/rtl8168f-1.fw (not found?)
[ 29.798500] r8169 0000:03:00.0: eth0: unable to load firmware patch rtl_nic/rtl8168f-1.fw (-2)
[ 29.809502] r8169 0000:03:00.0: eth0: link down
[ 29.809513] r8169 0000:03:00.0: eth0: link down
[ 29.809734] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 32.371648] r8169 0000:03:00.0: eth0: link up
[ 32.371847] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 33.817176] Bluetooth: Core ver 2.16
[ 33.817204] NET: Registered protocol family 31
[ 33.817210] Bluetooth: HCI device and connection manager initialized
[ 33.817216] Bluetooth: HCI socket layer initialized
[ 33.817221] Bluetooth: L2CAP socket layer initialized
[ 33.817231] Bluetooth: SCO socket layer initialized
[ 33.844048] Bluetooth: RFCOMM TTY layer initialized
[ 33.844058] Bluetooth: RFCOMM socket layer initialized
[ 33.844063] Bluetooth: RFCOMM ver 1.11
[ 34.400243] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 34.400249] Bluetooth: BNEP filters: protocol multicast
[ 34.444958] lp0: using parport0 (interrupt-driven).
[ 34.810477] ppdev: user-space parallel port driver
[ 42.824074] eth0: no IPv6 routers present
[ 376.053914] sound-juicer: sending ioctl 2285 to a partition!
[ 376.054014] sound-juicer: sending ioctl 2285 to a partition!
[ 376.054090] sound-juicer: sending ioctl 2285 to a partition!
[ 1003.198319] sound-juicer: sending ioctl 2285 to a partition!
[ 1003.198401] sound-juicer: sending ioctl 2285 to a partition!
[/quote]

#12

Encore:

0 [ 1.752607] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.752609] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.752612] usb usb1: Product: EHCI Host Controller [ 1.752613] usb usb1: Manufacturer: Linux 3.2.0-4-686-pae ehci_hcd [ 1.752615] usb usb1: SerialNumber: 0000:00:12.2 [ 1.752721] hub 1-0:1.0: USB hub found [ 1.752726] hub 1-0:1.0: 6 ports detected [ 1.752828] ehci_hcd 0000:00:13.2: EHCI Host Controller [ 1.752837] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [ 1.752845] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround [ 1.752866] ehci_hcd 0000:00:13.2: debug port 1 [ 1.752890] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfcfff400 [ 1.760546] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.764053] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00 [ 1.764069] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.764072] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.764073] usb usb3: Product: EHCI Host Controller [ 1.764075] usb usb3: Manufacturer: Linux 3.2.0-4-686-pae ehci_hcd [ 1.764076] usb usb3: SerialNumber: 0000:00:13.2 [ 1.764153] hub 3-0:1.0: USB hub found [ 1.764157] hub 3-0:1.0: 6 ports detected [ 1.764250] pata_atiixp 0000:00:14.1: setting latency timer to 64 [ 1.764518] scsi0 : pata_atiixp [ 1.765186] scsi1 : pata_atiixp [ 1.766393] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14 [ 1.766397] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15 [ 1.766444] ohci_hcd 0000:00:12.0: OHCI Host Controller [ 1.766455] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4 [ 1.766479] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfcffe000 [ 1.815577] xhci_hcd 0000:02:00.0: irq 44 for MSI/MSI-X [ 1.815581] xhci_hcd 0000:02:00.0: irq 45 for MSI/MSI-X [ 1.815585] xhci_hcd 0000:02:00.0: irq 46 for MSI/MSI-X [ 1.815589] xhci_hcd 0000:02:00.0: irq 47 for MSI/MSI-X [ 1.815592] xhci_hcd 0000:02:00.0: irq 48 for MSI/MSI-X [ 1.815649] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.815651] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.815652] usb usb2: Product: xHCI Host Controller [ 1.815653] usb usb2: Manufacturer: Linux 3.2.0-4-686-pae xhci_hcd [ 1.815655] usb usb2: SerialNumber: 0000:02:00.0 [ 1.815714] xHCI xhci_add_endpoint called for root hub [ 1.815715] xHCI xhci_check_bandwidth called for root hub [ 1.815735] hub 2-0:1.0: USB hub found [ 1.815740] hub 2-0:1.0: 2 ports detected [ 1.815782] xhci_hcd 0000:02:00.0: xHCI Host Controller [ 1.815786] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 5 [ 1.815807] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003 [ 1.815809] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.815810] usb usb5: Product: xHCI Host Controller [ 1.815812] usb usb5: Manufacturer: Linux 3.2.0-4-686-pae xhci_hcd [ 1.815813] usb usb5: SerialNumber: 0000:02:00.0 [ 1.815866] xHCI xhci_add_endpoint called for root hub [ 1.815867] xHCI xhci_check_bandwidth called for root hub [ 1.815885] hub 5-0:1.0: USB hub found [ 1.815889] hub 5-0:1.0: 2 ports detected [ 1.824047] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.824050] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.824051] usb usb4: Product: OHCI Host Controller [ 1.824053] usb usb4: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd [ 1.824054] usb usb4: SerialNumber: 0000:00:12.0 [ 1.824139] hub 4-0:1.0: USB hub found [ 1.824145] hub 4-0:1.0: 3 ports detected [ 1.824200] ohci_hcd 0000:00:12.1: OHCI Host Controller [ 1.824206] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 6 [ 1.824218] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfcffd000 [ 1.884043] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.884046] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.884048] usb usb6: Product: OHCI Host Controller [ 1.884049] usb usb6: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd [ 1.884050] usb usb6: SerialNumber: 0000:00:12.1 [ 1.884141] hub 6-0:1.0: USB hub found [ 1.884147] hub 6-0:1.0: 3 ports detected [ 1.884215] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 1.884222] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 7 [ 1.884241] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfcffc000 [ 1.936448] ata2.00: ATA-8: SAMSUNG HD502HJ, 1AJ100E4, max UDMA/133 [ 1.936450] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.936456] ata2.01: ATAPI: TSSTcorp CDDVDW SH-S223F, SB00, max UDMA/100 [ 1.944021] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.944023] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.944025] usb usb7: Product: OHCI Host Controller [ 1.944026] usb usb7: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd [ 1.944027] usb usb7: SerialNumber: 0000:00:13.0 [ 1.944374] hub 7-0:1.0: USB hub found [ 1.944381] hub 7-0:1.0: 3 ports detected [ 1.944455] ata2.00: configured for UDMA/100 [ 1.944466] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 1.944472] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 8 [ 1.944483] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfcffb000 [ 1.960342] ata2.01: configured for UDMA/100 [ 1.960681] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD502HJ 1AJ1 PQ: 0 ANSI: 5 [ 1.961364] scsi 1:0:1:0: CD-ROM TSSTcorp CDDVDW SH-S223F SB00 PQ: 0 ANSI: 5 [ 2.004042] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.004045] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.004046] usb usb8: Product: OHCI Host Controller [ 2.004048] usb usb8: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd [ 2.004049] usb usb8: SerialNumber: 0000:00:13.1 [ 2.004137] hub 8-0:1.0: USB hub found [ 2.004144] hub 8-0:1.0: 3 ports detected [ 2.004200] ohci_hcd 0000:00:14.5: OHCI Host Controller [ 2.004206] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 9 [ 2.004217] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfcffa000 [ 2.064025] usb usb9: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.064026] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.064028] usb usb9: Product: OHCI Host Controller [ 2.064029] usb usb9: Manufacturer: Linux 3.2.0-4-686-pae ohci_hcd [ 2.064030] usb usb9: SerialNumber: 0000:00:14.5 [ 2.064120] hub 9-0:1.0: USB hub found [ 2.064125] hub 9-0:1.0: 2 ports detected [ 2.064220] ahci 0000:00:11.0: version 3.0 [ 2.064326] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 2.064330] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc [ 2.064730] scsi2 : ahci [ 2.065029] scsi3 : ahci [ 2.065156] scsi4 : ahci [ 2.065256] scsi5 : ahci [ 2.065377] ata3: SATA max UDMA/133 abar m1024@0xfcfffc00 port 0xfcfffd00 irq 22 [ 2.065381] ata4: SATA max UDMA/133 abar m1024@0xfcfffc00 port 0xfcfffd80 irq 22 [ 2.065384] ata5: SATA max UDMA/133 abar m1024@0xfcfffc00 port 0xfcfffe00 irq 22 [ 2.065387] ata6: SATA max UDMA/133 abar m1024@0xfcfffc00 port 0xfcfffe80 irq 22 [ 2.184023] usb 1-2: new high-speed USB device number 3 using ehci_hcd [ 2.264022] Refined TSC clocksource calibration: 3817.137 MHz. [ 2.264025] Switching to clocksource tsc [ 2.384039] ata4: SATA link down (SStatus 0 SControl 300) [ 2.556020] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.556041] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.556060] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.556661] ata3.00: ATA-8: SAMSUNG HD161HJ, GF100-07, max UDMA7 [ 2.556664] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.557135] ata5.00: ATA-8: ST3500418AS, CC46, max UDMA/133 [ 2.557137] ata5.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 2.557303] ata3.00: configured for UDMA/133 [ 2.557387] scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD161HJ GF10 PQ: 0 ANSI: 5 [ 2.558423] ata5.00: configured for UDMA/133 [ 2.558486] scsi 4:0:0:0: Direct-Access ATA ST3500418AS CC46 PQ: 0 ANSI: 5 [ 2.574429] ata6.00: ATA-7: WDC WD3200AAKS-22SBA0, 12.01B01, max UDMA/133 [ 2.574431] ata6.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 2.575169] ata6.00: configured for UDMA/133 [ 2.575232] scsi 5:0:0:0: Direct-Access ATA WDC WD3200AAKS-2 12.0 PQ: 0 ANSI: 5 [ 2.579804] sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 2.583057] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.583059] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.583097] sd 1:0:0:0: [sda] Write Protect is off [ 2.583100] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.583116] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.583160] sr 1:0:1:0: Attached scsi CD-ROM sr0 [ 2.583420] sd 2:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 2.583454] sd 4:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 2.583465] sd 2:0:0:0: [sdb] Write Protect is off [ 2.583467] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.583483] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.583489] sd 4:0:0:0: [sdc] Write Protect is off [ 2.583491] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 2.583498] sd 5:0:0:0: [sdd] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2.583507] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.583539] sd 5:0:0:0: [sdd] Write Protect is off [ 2.583542] sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 2.583559] sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.591501] sda: sda1 sda2 sda3 [ 2.591728] sd 1:0:0:0: [sda] Attached SCSI disk [ 2.597199] sdb: sdb1 sdb2 sdb3 sdb4 [ 2.597523] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 2.597563] sr 1:0:1:0: Attached scsi generic sg1 type 5 [ 2.597584] sd 2:0:0:0: [sdb] Attached SCSI disk [ 2.597600] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 2.597632] sd 4:0:0:0: Attached scsi generic sg3 type 0 [ 2.597664] sd 5:0:0:0: Attached scsi generic sg4 type 0 [ 2.604240] sdd: sdd1 sdd2 < sdd5 > [ 2.604297] sdc: sdc1 sdc2 sdc3 [ 2.604496] sd 5:0:0:0: [sdd] Attached SCSI disk [ 2.604603] sd 4:0:0:0: [sdc] Attached SCSI disk [ 3.444415] PM: Starting manual resume from disk [ 3.444417] PM: Hibernation image partition 8:17 present [ 3.444418] PM: Looking for hibernation image. [ 3.444610] PM: Image not found (code -22) [

#13

Tu n’as pas clarifié cette partie,

[quote=“Zbf”]Donc en gros t’es en train de dire que quel que soit le système d’exploitation, tu n’arrives pas à accéder à tes disques durs ?

C’est effectivement étrange. Sur une autre machine ces disques durs fonctionnent ?
[/quote]

Ton dmesg indique beaucoup de disques durs, mais je ne distingue pas bien ceux qui sont internes de ceux qui sont externes.

Le résultat de [mono]df -T[/mono] clarifierait un peu.

Certains de tes disques demandent à être fsckisés, donc que tu lances [mono]fsck[/mono] dessus.

Aussi, il serait judicieux de ne brancher tes disques durs USB qu’un temps après le démarrage de ton système, et un par un, pour distinguer ce qui se passe dans [mono]dmesg[/mono].

#14

Dans ce que je vois rapidement, tu as

4 disques durs (3 et 4 partitions non étendues, 2 partitions + une étendue, 3 partitions non étendues)

1 disque SCSI une seule partition 7G (!? bizarremais bon)

2 disques de 620 et 1T une seule partition

Il n’y a rien d’autre

#15

Salut
Voici ce que donne df -T

df -T
Sys. fich. Type 1K-blocks Util. Disponible Uti% Monté sur
rootfs rootfs 30233928 16527472 12170644 58% /
udev devtmpfs 10240 0 10240 0% /dev
tmpfs tmpfs 413000 820 412180 1% /run
/dev/disk/by-uuid/a4013b25-f58f-49d9-8752-8b1fab310e2f ext4 30233928 16527472 12170644 58% /
tmpfs tmpfs 5120 0 5120 0% /run/lock
/dev/sde1 ext3 307663800 22771276 269264092 8% /media/usb0
tmpfs tmpfs 1645300 76 1645224 1% /run/shm
/dev/sda3 ext4 22240292 10985364 10125160 53% /media/Arquivo
/dev/sdc5 fuseblk 204796588 50537720 154258868 25% /media/DADOS_XP
/dev/sdb3 ext4 425274720 185458880 218213076 46% /media/Imagens
/dev/sdb2 ext4 50395844 5858052 41977792 13% /media/Lucid
/dev/sdd3 ext4 403706592 60325152 322874256 16% /media/Pessoais
/dev/sda4 ext3 97327372 7092380 85290992 8% /media/dados
/dev/sdd2 ext4 73487608 12860328 59582044 18% /media/sdd2
/dev/sdc1 fuseblk 107763988 24481884 83282104 23% /media/windows
/dev/sdf1 fuseblk 732572532 106541320 626031212 15% /media/TOSHIBA EXT
carlos@nexus:~$
Curieux, il y a un disque IDE externe qui est toujours détecté.
Les difficultés sont surtout avec un hub.

#16

et sdg (320G tout de même?)

Que donne ls -l /dev/sd*

#17

Bonjour
Voici le résultat de la commande:

[quote]$ ls -l /dev/sd*
brw-rw—T 1 root disk 8, 0 mars 20 08:55 /dev/sda
brw-rw—T 1 root disk 8, 1 mars 20 08:55 /dev/sda1
brw-rw—T 1 root disk 8, 2 mars 20 08:55 /dev/sda2
brw-rw—T 1 root disk 8, 3 mars 20 08:55 /dev/sda3
brw-rw—T 1 root disk 8, 16 mars 20 08:55 /dev/sdb
brw-rw—T 1 root disk 8, 17 mars 20 08:55 /dev/sdb1
brw-rw—T 1 root disk 8, 18 mars 20 08:55 /dev/sdb2
brw-rw—T 1 root disk 8, 19 mars 20 08:55 /dev/sdb3
brw-rw—T 1 root disk 8, 20 mars 20 08:55 /dev/sdb4
brw-rw—T 1 root disk 8, 32 mars 20 08:55 /dev/sdc
brw-rw—T 1 root disk 8, 33 mars 20 08:55 /dev/sdc1
brw-rw—T 1 root disk 8, 34 mars 20 08:55 /dev/sdc2
brw-rw—T 1 root disk 8, 35 mars 20 08:55 /dev/sdc3
brw-rw—T 1 root disk 8, 48 mars 20 08:55 /dev/sdd
brw-rw—T 1 root disk 8, 49 mars 20 08:55 /dev/sdd1
brw-rw—T 1 root disk 8, 50 mars 20 08:55 /dev/sdd2
brw-rw—T 1 root disk 8, 53 mars 20 08:55 /dev/sdd5
brw-rw—T 1 root floppy 8, 64 mars 20 08:55 /dev/sde
brw-rw—T 1 root floppy 8, 65 mars 20 08:55 /dev/sde1
brw-rw—T 1 root floppy 8, 80 mars 20 08:55 /dev/sdf
brw-rw—T 1 root floppy 8, 81 mars 20 08:55 /dev/sdf1
[/quote]

#18

les deux disques (1T et 620G) branchés? brw-rw---T 1 root disk 8, 0 mars 20 08:55 /dev/sda disque 3 partitions non étendues brw-rw---T 1 root disk 8, 1 mars 20 08:55 /dev/sda1 brw-rw---T 1 root disk 8, 2 mars 20 08:55 /dev/sda2 brw-rw---T 1 root disk 8, 3 mars 20 08:55 /dev/sda3 brw-rw---T 1 root disk 8, 16 mars 20 08:55 /dev/sdb disque 4 part non étendues brw-rw---T 1 root disk 8, 17 mars 20 08:55 /dev/sdb1 brw-rw---T 1 root disk 8, 18 mars 20 08:55 /dev/sdb2 brw-rw---T 1 root disk 8, 19 mars 20 08:55 /dev/sdb3 brw-rw---T 1 root disk 8, 20 mars 20 08:55 /dev/sdb4 brw-rw---T 1 root disk 8, 32 mars 20 08:55 /dev/sdc disque 3 partitions non étendues brw-rw---T 1 root disk 8, 33 mars 20 08:55 /dev/sdc1 brw-rw---T 1 root disk 8, 34 mars 20 08:55 /dev/sdc2 brw-rw---T 1 root disk 8, 35 mars 20 08:55 /dev/sdc3 brw-rw---T 1 root disk 8, 48 mars 20 08:55 /dev/sdd 2 partitions non étendues + 1 étendue brw-rw---T 1 root disk 8, 49 mars 20 08:55 /dev/sdd1 brw-rw---T 1 root disk 8, 50 mars 20 08:55 /dev/sdd2 brw-rw---T 1 root disk 8, 53 mars 20 08:55 /dev/sdd5 brw-rw---T 1 root floppy 8, 64 mars 20 08:55 /dev/sde disque 7G (?) brw-rw---T 1 root floppy 8, 65 mars 20 08:55 /dev/sde1 brw-rw---T 1 root floppy 8, 80 mars 20 08:55 /dev/sdf était le disque 620G brw-rw---T 1 root floppy 8, 81 mars 20 08:55 /dev/sdf1

qu’y avait-il de branché?

#19

~$ ls -l /dev/sd*
brw-rw—T 1 root disk 8, 0 mars 22 07:43 /dev/sda
brw-rw—T 1 root disk 8, 1 mars 22 07:43 /dev/sda1
brw-rw—T 1 root disk 8, 2 mars 22 07:43 /dev/sda2
brw-rw—T 1 root disk 8, 3 mars 22 07:43 /dev/sda3
brw-rw—T 1 root disk 8, 4 mars 22 07:43 /dev/sda4
brw-rw—T 1 root disk 8, 16 mars 22 07:43 /dev/sdb
brw-rw—T 1 root disk 8, 17 mars 22 07:43 /dev/sdb1
brw-rw—T 1 root disk 8, 18 mars 22 07:43 /dev/sdb2
brw-rw—T 1 root disk 8, 19 mars 22 07:43 /dev/sdb3
brw-rw—T 1 root disk 8, 32 mars 22 07:43 /dev/sdc
brw-rw—T 1 root disk 8, 33 mars 22 07:43 /dev/sdc1
brw-rw—T 1 root disk 8, 34 mars 22 07:43 /dev/sdc2
brw-rw—T 1 root disk 8, 37 mars 22 07:43 /dev/sdc5
brw-rw—T 1 root disk 8, 48 mars 22 07:43 /dev/sdd
brw-rw—T 1 root disk 8, 49 mars 22 07:43 /dev/sdd1
brw-rw—T 1 root disk 8, 50 mars 22 07:43 /dev/sdd2
brw-rw—T 1 root disk 8, 51 mars 22 07:43 /dev/sdd3
brw-rw—T 1 root floppy 8, 64 mars 22 07:43 /dev/sde
brw-rw—T 1 root floppy 8, 65 mars 22 07:43 /dev/sde1
brw-rw—T 1 root floppy 8, 80 mars 22 07:43 /dev/sdf
brw-rw—T 1 root floppy 8, 81 mars 22 07:43 /dev/sdf1
brw-rw—T 1 root floppy 8, 96 mars 22 07:57 /dev/sdg
brw-rw—T 1 root floppy 8, 97 mars 22 07:57 /dev/sdg1

Bonjour
J’ai répété la commande avec ces disques usb branchés:

Un disque externe IDE que l’on voit toujours
Un disque externe branché à une porte usb 3. Celui-là se voit.
Une clé flash drive branché à une porte usb en avant de la tour.
Deux disques externes non IDE branchés à deux portes usb d’un hub. Ceux -là n’apparaissent pas.
/dev/sdg1 c’est la clé
/dev/sdf1 c’est le disque en usb3
/dev/sde1 c’est le disque externe IDE

#20

Le système voit 7 périphériques. Tu en énonces 5. Je suppose donc que tu as 2 disques internes sda et sdb.

Essaye de faire sous root

for i in sde1 sdf1 sdg1 ; do mount /dev/${i} /mnt ls -l /mnt umount /dev/${i} done
ce script monte les périphériques sde1->sdg1 à la main sous /mnt et liste le contenu.
Donne les messages d’erreurs.

(Tu peux copier/coller mais il te faut être root).