Faire une borne d'accès wifi

Support Debian
#1

J’ai une clef usb wifi linksys AE1000 , je voudrais savoir si je peux m’en servir pour permettre à tout un tas de petits appareils mobiles de se connecter en wifi grace à la connection de ma Debian Squeeze :

Premièrement : Pour installer le pilote ralink RT_3572 , il semblerait que je doive installer ce paquet : linux-headers-generic qui n’est pas disponible dans mes paquetages . ( je suis les indications de ce fil ubuntu : http://ubuntuforums.org/showpost.php?p=10163301&postcount=7 .

Deuxièmement : il faudra que j’arrive à faire de cette clef une borne d’accès wifi , complètement ouverte ( pas gênant , dans ma cambrousse ) pour que toute la famille puisse se connecter par ce seul moyen .

Pour l’instant , voilà le retour que j’ai à un lsusb , la clef est reconnue :

Bus 001 Device 003: ID 13b1:002f Linksys AE1000 v1 802.11n [Ralink RT3572]

Je me demande si je n’ai pas déjà installé le pilote vu que ça me marque Ralink RT3572 ?

Je vous remercie de tous vos bons conseils éventuels …

#2

Bonjour

A priori le chipset de ta clé est le ralink RT3572, le support est différent selon la version de Debian

pour Wheezy (la prochaine debian stable)
wiki.debian.org/rt2800usb

pour Squeeze
wiki.debian.org/rt2870sta

dans tous les cas, il faut le firmware (paquet firmware-ralink)

Ensuite, une fois la clé reconnue, il te faut créér un point d’accès wifi avec le logiciel hostapd.

Un petit tuto que j’ai écrit sur le sujet (avec un autre modèle de clé wifi mais le principe est le même)
agentoss.wordpress.com/2011/10/3 … ian-linux/

#3

Merci de me répondre ,

Mes paquets firmware-ralink et wireless-tools sont déjà installés , j’avais dû faire ça dans de précédentes tentatives

Malheureusement , quand je tape iwconfig , j’obtiens ça :

[b]lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.[/b]

Quand je fais lsmod , j’obtiens l’affichage ci-dessous , je me demande si le bon module est bien présent ?

kri@cilalos2:~$ lsmod
Module Size Used by
sco 5885 2
ppdev 4058 0
lp 5570 0
bridge 33031 0
stp 996 1 bridge
bnep 7452 2
l2cap 21721 3 bnep
bluetooth 36319 5 sco,bnep,l2cap
acpi_cpufreq 4951 0
rfkill 10264 3 bluetooth
cpufreq_conservative 4018 0
cpufreq_powersave 602 0
cpufreq_userspace 1480 0
cpufreq_stats 1997 0
binfmt_misc 4907 1
fuse 44268 5
loop 9769 0
snd_hda_codec_realtek 163378 1
snd_hda_intel 16823 2
snd_hda_codec 46002 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 4054 1 snd_hda_codec
snd_pcm_oss 28671 0
snd_mixer_oss 10461 1 snd_pcm_oss
snd_pcm 47226 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_midi 3576 0
snd_rawmidi 12513 1 snd_seq_midi
snd_seq_midi_event 3684 1 snd_seq_midi
snd_seq 35463 3 snd_seq_midi,snd_seq_midi_event
snd_timer 12270 2 snd_pcm,snd_seq
parport_pc 15799 1
psmouse 44809 0
snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq
i2c_i801 6462 0
parport 22554 3 ppdev,lp,parport_pc
button 3598 0
rng_core 2178 0
processor 26327 1 acpi_cpufreq
snd 34423 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pcspkr 1207 0
evdev 5609 7
serio_raw 2916 0
nvidia 9842520 60
soundcore 3450 1 snd
i2c_core 12787 2 i2c_i801,nvidia
snd_page_alloc 5045 2 snd_hda_intel,snd_pcm
ext4 256936 2
mbcache 3762 1 ext4
jbd2 56251 1 ext4
crc16 1027 2 l2cap,ext4
usb_storage 31033 0
sg 19937 0
sd_mod 26013 3
crc_t10dif 1012 1 sd_mod
sr_mod 10770 0
cdrom 26487 1 sr_mod
ata_generic 2247 0
ata_piix 17736 2
uhci_hcd 16057 0
thermal 9206 0
floppy 40923 0
thermal_sys 9378 2 processor,thermal
libata 115889 2 ata_generic,ata_piix
ehci_hcd 28689 0
r8169 31333 0
mii 2714 1 r8169
scsi_mod 105001 5 usb_storage,sg,sd_mod,sr_mod,libata
usbcore 99329 4 usb_storage,uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore

Merci pour l’info sur le logiciel hotstapd , j’ai l’impression que c’est ce qui me manquait .

#4

On dirait que le module n’est pas chargé.

essaye

modprobe rt2870sta

essaye aussi un dmesg pour voir ce que ça dit

cf la section “Troubleshooting” du wiki donné plus haut (blacklister le module rt2800usb)

#5

La réponse au dmesg est un peu longue :

[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at e4000000 (gap: e4000000:1ac00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c3000000 s34328 r0 d23016 u1048576
[ 0.000000] pcpu-alloc: s34328 r0 d23016 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 844929
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=da0b1b6a-a8dc-45f1-8310-bc3894639c68 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore… done.
[ 0.000000] Enabling unmasked SIMD FPU exception support… done.
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Initializing HighMem for node 0 (000373fe:000cfee0)
[ 0.000000] Memory: 3363964k/3406720k available (2506k kernel code, 41200k reserved, 1326k data, 380k init, 2501512k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13bf000 - 0xc141e000 ( 380 kB)
[ 0.000000] .data : 0xc1272a57 - 0xc13be4c4 (1326 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1272a57 (2506 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode…Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2800.297 MHz processor.
[ 0.004004] Calibrating delay loop (skipped), value calculated using timer frequency… 5600.59 BogoMIPS (lpj=11201188)
[ 0.004017] Security Framework initialized
[ 0.004021] SELinux: Disabled at boot.
[ 0.004027] Mount-cache hash table entries: 512
[ 0.004124] Initializing cgroup subsys ns
[ 0.004128] Initializing cgroup subsys cpuacct
[ 0.004131] Initializing cgroup subsys devices
[ 0.004133] Initializing cgroup subsys freezer
[ 0.004135] Initializing cgroup subsys net_cls
[ 0.004153] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004155] CPU: L2 cache: 3072K
[ 0.004157] CPU: Physical Processor ID: 0
[ 0.004159] CPU: Processor Core ID: 0
[ 0.004161] mce: CPU supports 6 MCE banks
[ 0.004168] CPU0: Thermal monitoring enabled (TM2)
[ 0.004171] using mwait in idle threads.
[ 0.004176] Performance Events: Core2 events, Intel PMU driver.
[ 0.004181] … version: 2
[ 0.004182] … bit width: 40
[ 0.004184] … generic registers: 2
[ 0.004185] … value mask: 000000ffffffffff
[ 0.004186] … max period: 000000007fffffff
[ 0.004188] … fixed-purpose events: 3
[ 0.004189] … event mask: 0000000700000003
[ 0.004194] Checking ‘hlt’ instruction… OK.
[ 0.021087] ACPI: Core revision 20090903
[ 0.025662] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.025990] …TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.065684] CPU0: Intel® Core™2 Duo CPU E7400 @ 2.80GHz stepping 0a
[ 0.068001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008000] CPU: L2 cache: 3072K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU1: Thermal monitoring enabled (TM2)
[ 0.152059] CPU1: Intel® Core™2 Duo CPU E7400 @ 2.80GHz stepping 0a
[ 0.152065] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.156043] Brought up 2 CPUs
[ 0.156046] Total of 2 processors activated (11200.50 BogoMIPS).
[ 0.157092] CPU0 attaching sched-domain:
[ 0.157096] domain 0: span 0-1 level MC
[ 0.157098] groups: group c3003778 cpus 0 group c3103778 cpus 1
[ 0.157103] CPU1 attaching sched-domain:
[ 0.157105] domain 0: span 0-1 level MC
[ 0.157107] groups: group c3103778 cpus 1 group c3003778 cpus 0
[ 0.157158] devtmpfs: initialized
[ 0.157158] regulator: core version 0.5
[ 0.157158] NET: Registered protocol family 16
[ 0.157158] ACPI: bus type pci registered
[ 0.157158] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
[ 0.157158] PCI: MCFG area at e0000000 reserved in E820
[ 0.157158] PCI: Using MMCONFIG for extended config space
[ 0.157158] PCI: Using configuration type 1 for base access
[ 0.157158] bio: create slab at 0
[ 0.157158] ACPI: EC: Look up EC in DSDT
[ 0.162394] ACPI: Interpreter enabled
[ 0.162401] ACPI: (supports S0 S3 S4 S5)
[ 0.162419] ACPI: Using IOAPIC for interrupt routing
[ 0.165844] ACPI: No dock devices found.
[ 0.165919] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.166000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.166003] pci 0000:00:01.0: PME# disabled
[ 0.166053] pci 0000:00:1b.0: reg 10 64bit mmio: [0xe9100000-0xe9103fff]
[ 0.166088] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.166092] pci 0000:00:1b.0: PME# disabled
[ 0.166143] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.166146] pci 0000:00:1c.0: PME# disabled
[ 0.166200] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.166204] pci 0000:00:1c.3: PME# disabled
[ 0.166243] pci 0000:00:1d.0: reg 20 io port: [0xe000-0xe01f]
[ 0.166284] pci 0000:00:1d.1: reg 20 io port: [0xe100-0xe11f]
[ 0.166325] pci 0000:00:1d.2: reg 20 io port: [0xe200-0xe21f]
[ 0.166365] pci 0000:00:1d.3: reg 20 io port: [0xe300-0xe31f]
[ 0.166404] pci 0000:00:1d.7: reg 10 32bit mmio: [0xe9104000-0xe91043ff]
[ 0.166547] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 000f)
[ 0.166550] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f)
[ 0.166590] pci 0000:00:1f.2: reg 10 io port: [0x00-0x07]
[ 0.166595] pci 0000:00:1f.2: reg 14 io port: [0x00-0x03]
[ 0.166600] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
[ 0.166605] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
[ 0.166610] pci 0000:00:1f.2: reg 20 io port: [0xf000-0xf00f]
[ 0.166630] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.166633] pci 0000:00:1f.2: PME# disabled
[ 0.166672] pci 0000:00:1f.3: reg 20 io port: [0x500-0x51f]
[ 0.166716] pci 0000:01:00.0: reg 10 32bit mmio: [0xe6000000-0xe6ffffff]
[ 0.166724] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.166732] pci 0000:01:00.0: reg 1c 64bit mmio: [0xe4000000-0xe5ffffff]
[ 0.166737] pci 0000:01:00.0: reg 24 io port: [0xc000-0xc07f]
[ 0.166742] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.166837] pci 0000:00:01.0: bridge io port: [0xc000-0xcfff]
[ 0.166840] pci 0000:00:01.0: bridge 32bit mmio: [0xe4000000-0xe7ffffff]
[ 0.166844] pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.166876] pci 0000:00:1c.0: bridge io port: [0xb000-0xbfff]
[ 0.166923] pci 0000:03:00.0: reg 10 io port: [0xd000-0xd0ff]
[ 0.166941] pci 0000:03:00.0: reg 18 64bit mmio pref: [0xe9010000-0xe9010fff]
[ 0.166954] pci 0000:03:00.0: reg 20 64bit mmio pref: [0xe9000000-0xe900ffff]
[ 0.166961] pci 0000:03:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
[ 0.166996] pci 0000:03:00.0: supports D1 D2
[ 0.166998] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.167003] pci 0000:03:00.0: PME# disabled
[ 0.172081] pci 0000:00:1c.3: bridge io port: [0xd000-0xdfff]
[ 0.172086] pci 0000:00:1c.3: bridge 32bit mmio: [0xe8000000-0xe8ffffff]
[ 0.172092] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xe9000000-0xe90fffff]
[ 0.172143] pci 0000:00:1e.0: transparent bridge
[ 0.172147] pci 0000:00:1e.0: bridge io port: [0xa000-0xafff]
[ 0.172170] pci_bus 0000:00: on NUMA node 0
[ 0.172175] ACPI: PCI Interrupt Routing Table [_SB_.PCI0.PRT]
[ 0.172301] ACPI: PCI Interrupt Routing Table [_SB.PCI0.PEX0.PRT]
[ 0.172351] ACPI: PCI Interrupt Routing Table [_SB.PCI0.PEX3.PRT]
[ 0.172401] ACPI: PCI Interrupt Routing Table [_SB.PCI0.HUB0._PRT]
[ 0.180331] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.180406] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.180481] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.180553] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.180627] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.180700] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.180772] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.180845] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.180925] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.180927] vgaarb: loaded
[ 0.180940] PCI: Using ACPI for IRQ routing
[ 0.180940] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.180940] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.180940] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.184016] Switching to clocksource tsc
[ 0.185085] pnp: PnP ACPI init
[ 0.185091] ACPI: bus type pnp registered
[ 0.187178] pnp: PnP ACPI: found 16 devices
[ 0.187180] ACPI: ACPI bus type pnp unregistered
[ 0.187184] PnPBIOS: Disabled by ACPI PNP
[ 0.187191] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.187193] system 00:01: ioport range 0x290-0x29f has been reserved
[ 0.187196] system 00:01: ioport range 0x800-0x87f has been reserved
[ 0.187198] system 00:01: ioport range 0x290-0x294 has been reserved
[ 0.187200] system 00:01: ioport range 0x880-0x88f has been reserved
[ 0.187207] system 00:0c: ioport range 0x400-0x4bf has been reserved
[ 0.187211] system 00:0d: iomem range 0xe0000000-0xe3ffffff has been reserved
[ 0.187216] system 00:0e: iomem range 0xcd200-0xcffff has been reserved
[ 0.187218] system 00:0e: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.187221] system 00:0e: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.187223] system 00:0e: iomem range 0xfc000-0xfffff could not be reserved
[ 0.187226] system 00:0e: iomem range 0xcfee0000-0xcfefffff could not be reserved
[ 0.187228] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 0.187231] system 00:0e: iomem range 0x100000-0xcfedffff could not be reserved
[ 0.187233] system 00:0e: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.187236] system 00:0e: iomem range 0xfed13000-0xfed1dfff has been reserved
[ 0.187238] system 00:0e: iomem range 0xfed20000-0xfed8ffff has been reserved
[ 0.187241] system 00:0e: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.187243] system 00:0e: iomem range 0xffb00000-0xffb7ffff has been reserved
[ 0.187246] system 00:0e: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.187248] system 00:0e: iomem range 0xe0000-0xeffff has been reserved
[ 0.221904] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.221907] pci 0000:00:01.0: IO window: 0xc000-0xcfff
[ 0.221910] pci 0000:00:01.0: MEM window: 0xe4000000-0xe7ffffff
[ 0.221914] pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
[ 0.221917] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.221920] pci 0000:00:1c.0: IO window: 0xb000-0xbfff
[ 0.221924] pci 0000:00:1c.0: MEM window: 0xe9200000-0xe93fffff
[ 0.221928] pci 0000:00:1c.0: PREFETCH window: 0x000000e9400000-0x000000e95fffff
[ 0.221934] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:03
[ 0.221936] pci 0000:00:1c.3: IO window: 0xd000-0xdfff
[ 0.221941] pci 0000:00:1c.3: MEM window: 0xe8000000-0xe8ffffff
[ 0.221944] pci 0000:00:1c.3: PREFETCH window: 0x000000e9000000-0x000000e90fffff
[ 0.221950] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[ 0.221952] pci 0000:00:1e.0: IO window: 0xa000-0xafff
[ 0.221956] pci 0000:00:1e.0: MEM window: disabled
[ 0.221959] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.221970] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.221973] pci 0000:00:01.0: setting latency timer to 64
[ 0.221980] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.221983] pci 0000:00:1c.0: setting latency timer to 64
[ 0.221990] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.221994] pci 0000:00:1c.3: setting latency timer to 64
[ 0.221999] pci 0000:00:1e.0: setting latency timer to 64
[ 0.222002] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.222004] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.222006] pci_bus 0000:01: resource 0 io: [0xc000-0xcfff]
[ 0.222009] pci_bus 0000:01: resource 1 mem: [0xe4000000-0xe7ffffff]
[ 0.222011] pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.222013] pci_bus 0000:02: resource 0 io: [0xb000-0xbfff]
[ 0.222015] pci_bus 0000:02: resource 1 mem: [0xe9200000-0xe93fffff]
[ 0.222018] pci_bus 0000:02: resource 2 pref mem [0xe9400000-0xe95fffff]
[ 0.222020] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff]
[ 0.222022] pci_bus 0000:03: resource 1 mem: [0xe8000000-0xe8ffffff]
[ 0.222024] pci_bus 0000:03: resource 2 pref mem [0xe9000000-0xe90fffff]
[ 0.222026] pci_bus 0000:04: resource 0 io: [0xa000-0xafff]
[ 0.222029] pci_bus 0000:04: resource 3 io: [0x00-0xffff]
[ 0.222031] pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffff]
[ 0.222053] NET: Registered protocol family 2
[ 0.222118] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.222326] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.222612] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.222759] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.222761] TCP reno registered
[ 0.222813] NET: Registered protocol family 1
[ 0.222900] pci 0000:01:00.0: Boot video device
[ 0.222932] Unpacking initramfs…
[ 0.423596] Freeing initrd memory: 8507k freed
[ 0.426952] audit: initializing netlink socket (disabled)
[ 0.426964] type=2000 audit(1331189041.423:1): initialized
[ 0.429948] highmem bounce pool size: 64 pages
[ 0.429952] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.431055] VFS: Disk quotas dquot_6.5.2
[ 0.431097] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.431157] msgmni has been set to 1703
[ 0.431306] alg: No test for stdrng (krng)
[ 0.431344] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.431347] io scheduler noop registered
[ 0.431348] io scheduler anticipatory registered
[ 0.431350] io scheduler deadline registered
[ 0.431376] io scheduler cfq registered (default)
[ 0.431465] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.431470] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.431550] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.431556] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.431648] pcieport 0000:00:1c.3: irq 26 for MSI/MSI-X
[ 0.431654] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.431821] isapnp: Scanning for PnP cards…
[ 0.784640] isapnp: No Plug & Play device found
[ 0.785679] Linux agpgart interface v0.103
[ 0.785775] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.785860] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.786128] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.786281] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.786682] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.786688] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.786754] mice: PS/2 mouse device common for all mice
[ 0.786811] rtc_cmos 00:04: RTC can wake from S4
[ 0.786848] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.786871] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.786887] cpuidle: using governor ladder
[ 0.786889] cpuidle: using governor menu
[ 0.786894] No iBFT detected.
[ 0.787186] TCP cubic registered
[ 0.787292] NET: Registered protocol family 10
[ 0.787867] Mobile IPv6
[ 0.787870] NET: Registered protocol family 17
[ 0.787881] Using IPI No-Shortcut mode
[ 0.787929] PM: Resume from disk failed.
[ 0.787937] registered taskstats version 1
[ 0.788166] rtc_cmos 00:04: setting system clock to 2012-03-08 06:44:01 UTC (1331189041)
[ 0.788204] Initalizing network drop monitor service
[ 0.788224] Freeing unused kernel memory: 380k freed
[ 0.788374] Write protecting the kernel text: 2508k
[ 0.788391] Write protecting the kernel read-only data: 920k
[ 0.800598] udev[56]: starting version 164
[ 0.803774] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.887351] usbcore: registered new interface driver usbfs
[ 0.887371] usbcore: registered new interface driver hub
[ 0.887667] usbcore: registered new device driver usb
[ 0.899448] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 0.899467] r8169 0000:03:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 0.899509] r8169 0000:03:00.0: setting latency timer to 64
[ 0.899556] r8169 0000:03:00.0: irq 27 for MSI/MSI-X
[ 0.900066] r8169 0000:03:00.0: eth0: RTL8168c/8111c at 0xf7d06000, 00:24:1d:14:f7:44, XID 1c4000c0 IRQ 27
[ 0.901281] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 0.901301] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.901309] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.901312] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.901326] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.901342] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.902080] SCSI subsystem initialized
[ 0.905232] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.905347] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe9104000
[ 0.918126] Floppy drive(s): fd0 is 1.44M
[ 0.920127] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.920155] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.920157] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.920159] usb usb1: Product: EHCI Host Controller
[ 0.920161] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 0.920163] usb usb1: SerialNumber: 0000:00:1d.7
[ 0.920254] usb usb1: configuration #1 chosen from 1 choice
[ 0.920305] hub 1-0:1.0: USB hub found
[ 0.920311] hub 1-0:1.0: 8 ports detected
[ 0.920835] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.920866] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.920873] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.920875] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.920883] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.920904] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e000
[ 0.920928] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.920930] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.920932] usb usb2: Product: UHCI Host Controller
[ 0.920934] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 0.920936] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.920984] usb usb2: configuration #1 chosen from 1 choice
[ 0.921005] hub 2-0:1.0: USB hub found
[ 0.921010] hub 2-0:1.0: 2 ports detected
[ 0.921045] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.921050] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.921053] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.921058] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.921084] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e100
[ 0.921108] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.921110] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.921112] usb usb3: Product: UHCI Host Controller
[ 0.921114] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 0.921115] usb usb3: SerialNumber: 0000:00:1d.1
[ 0.921117] libata version 3.00 loaded.
[ 0.921162] usb usb3: configuration #1 chosen from 1 choice
[ 0.921184] hub 3-0:1.0: USB hub found
[ 0.921189] hub 3-0:1.0: 2 ports detected
[ 0.921223] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.921228] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.921231] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.921236] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.921261] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e200
[ 0.921286] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.921288] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.921290] usb usb4: Product: UHCI Host Controller
[ 0.921292] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 0.921293] usb usb4: SerialNumber: 0000:00:1d.2
[ 0.921338] usb usb4: configuration #1 chosen from 1 choice
[ 0.921359] hub 4-0:1.0: USB hub found
[ 0.921364] hub 4-0:1.0: 2 ports detected
[ 0.921398] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.921402] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.921405] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.921410] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.921435] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e300
[ 0.921459] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.921461] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.921463] usb usb5: Product: UHCI Host Controller
[ 0.921465] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 0.921466] usb usb5: SerialNumber: 0000:00:1d.3
[ 0.921511] usb usb5: configuration #1 chosen from 1 choice
[ 0.921532] hub 5-0:1.0: USB hub found
[ 0.921536] hub 5-0:1.0: 2 ports detected
[ 0.923226] ata_piix 0000:00:1f.2: version 2.13
[ 0.923237] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.923241] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 0.923270] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.923581] scsi0 : ata_piix
[ 0.923670] scsi1 : ata_piix
[ 0.924261] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 0.924263] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 0.935451] FDC 0 is a post-1991 82077
[ 1.089636] ata1.00: HPA detected: current 240119615, native 240121728
[ 1.089642] ata1.00: ATA-7: Maxtor 6L120M0, BANC1E00, max UDMA/133
[ 1.089646] ata1.00: 240119615 sectors, multi 16: LBA NCQ (not used)
[ 1.105134] ata1.00: configured for UDMA/133
[ 1.105243] scsi 0:0:0:0: Direct-Access ATA Maxtor 6L120M0 BANC PQ: 0 ANSI: 5
[ 1.208294] ata2.00: ATAPI: DVD-ROM DDU1622, VER AS72, max UDMA/66
[ 1.208322] ata2.01: ATAPI: SONY DVD RW DW-Q28A, KYS1, max UDMA/66
[ 1.224206] ata2.00: configured for UDMA/66
[ 1.232512] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 1.240211] ata2.01: configured for UDMA/66
[ 1.241068] scsi 1:0:0:0: CD-ROM SONY DVD-ROM DDU1622 AS72 PQ: 0 ANSI: 5
[ 1.242019] scsi 1:0:1:0: CD-ROM SONY DVD RW DW-Q28A KYS1 PQ: 0 ANSI: 5
[ 1.250229] sr0: scsi3-mmc drive: 16x/40x cd/rw xa/form2 cdda tray
[ 1.250232] Uniform CD-ROM driver Revision: 3.20
[ 1.250369] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.251966] sd 0:0:0:0: [sda] 240119615 512-byte logical blocks: (122 GB/114 GiB)
[ 1.252018] sd 0:0:0:0: [sda] Write Protect is off
[ 1.252020] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.252038] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[ 1.252175] sda:sr1: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 1.254111] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 1.274390] sda1 sda2 sda3 sda4 < sda5 sda6 >
[ 1.290390] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.294212] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.294237] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.294260] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 1.369087] usb 1-1: New USB device found, idVendor=05e3, idProduct=0710
[ 1.369091] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 1.369095] usb 1-1: Product: USB Storage
[ 1.369097] usb 1-1: SerialNumber: 000000009144
[ 1.369177] usb 1-1: configuration #1 chosen from 1 choice
[ 1.375197] Initializing USB Mass Storage driver…
[ 1.375341] scsi2 : SCSI emulation for USB Mass Storage devices
[ 1.375398] usbcore: registered new interface driver usb-storage
[ 1.375400] USB Mass Storage support registered.
[ 1.375524] usb-storage: device found at 2
[ 1.375526] usb-storage: waiting for device to settle before scanning
[ 1.480513] usb 1-3: new high speed USB device using ehci_hcd and address 3
[ 1.630806] usb 1-3: New USB device found, idVendor=13b1, idProduct=002f
[ 1.630810] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.630813] usb 1-3: Product: Linksys AE1000
[ 1.630816] usb 1-3: Manufacturer: Linksys
[ 1.630898] usb 1-3: configuration #1 chosen from 1 choice
[ 1.939865] EXT4-fs (sda5): mounted filesystem with ordered data mode
[ 3.946494] udev[442]: starting version 164
[ 5.907988] nvidia: module license ‘NVIDIA’ taints kernel.
[ 5.907991] Disabling lock debugging due to kernel taint
[ 6.372528] usb-storage: device scan complete
[ 6.373763] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9144 PQ: 0 ANSI: 0
[ 6.375006] scsi 2:0:0:1: Direct-Access Generic STORAGE DEVICE 9144 PQ: 0 ANSI: 0
[ 6.376254] scsi 2:0:0:2: Direct-Access Generic STORAGE DEVICE 9144 PQ: 0 ANSI: 0
[ 6.377507] scsi 2:0:0:3: Direct-Access Generic STORAGE DEVICE 9144 PQ: 0 ANSI: 0
[ 6.377984] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 6.378195] sd 2:0:0:1: Attached scsi generic sg4 type 0
[ 6.378402] sd 2:0:0:2: Attached scsi generic sg5 type 0
[ 6.378611] sd 2:0:0:3: Attached scsi generic sg6 type 0
[ 6.390122] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[ 6.395944] sd 2:0:0:3: [sde] Attached SCSI removable disk
[ 6.403871] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 6.404870] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[ 6.548394] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 6.560619] ACPI: SSDT cfee6d80 0022A (v01 PmRef Cpu0Ist 00003000 INTL 20040311)
[ 6.560915] processor LNXCPU:00: registered as cooling_device0
[ 6.561082] ACPI: SSDT cfee7240 00152 (v01 PmRef Cpu1Ist 00003000 INTL 20040311)
[ 6.792570] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 6.792578] nvidia 0000:01:00.0: setting latency timer to 64
[ 6.792582] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 6.792685] processor LNXCPU:01: registered as cooling_device1
[ 6.792821] NVRM: loading NVIDIA UNIX x86 Kernel Module 195.36.31 Tue Jun 1 22:08:27 PDT 2010
[ 6.844054] rt3572sta: disagrees about version of symbol module_layout
[ 6.845062] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 6.845106] ACPI: Power Button [PWRB]
[ 6.845156] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 6.845175] ACPI: Power Button [PWRF]
[ 6.848723] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 6.850668] intel_rng: FWH not detected
[ 6.944221] parport_pc 00:09: reported by Plug and Play ACPI
[ 6.944263] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 7.403846] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.403868] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 7.496602] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
[ 7.650936] input: ImExPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 8.811110] loop: module loaded
[ 9.241758] EXT4-fs (sda6): mounted filesystem with ordered data mode
[ 10.465215] fuse init (API version 7.13)
[ 14.618023] r8169 0000:03:00.0: eth0: link down
[ 14.618031] r8169 0000:03:00.0: eth0: link down
[ 14.618186] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.221350] r8169 0000:03:00.0: eth0: link up
[ 16.221574] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.969187] Bluetooth: Core ver 2.15
[ 17.969702] NET: Registered protocol family 31
[ 17.969705] Bluetooth: HCI device and connection manager initialized
[ 17.969708] Bluetooth: HCI socket layer initialized
[ 18.024266] Bluetooth: L2CAP ver 2.14
[ 18.024269] Bluetooth: L2CAP socket layer initialized
[ 18.268950] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 18.268954] Bluetooth: BNEP filters: protocol multicast
[ 18.339153] Bridge firewalling registered
[ 18.516730] lp0: using parport0 (interrupt-driven).
[ 18.591083] ppdev: user-space parallel port driver
[ 18.869370] Bluetooth: SCO (Voice Link) ver 0.6
[ 18.869373] Bluetooth: SCO socket layer initialized
[ 26.852006] eth0: no IPv6 routers present
[ 388.960933] CPU0 attaching NULL sched-domain.
[ 388.960938] CPU1 attaching NULL sched-domain.
[ 388.988566] CPU0 attaching sched-domain:
[ 388.988570] domain 0: span 0-1 level MC
[ 388.988573] groups: group c3003778 cpus 0 group c3103778 cpus 1
[ 388.988581] CPU1 attaching sched-domain:
[ 388.988583] domain 0: span 0-1 level MC
[ 388.988586] groups: group c3103778 cpus 1 group c3003778 cpus 0
[22285.305812] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[22285.312082] rtusb init —>
[22285.312132] usbcore: registered new interface driver rt2870

!! Avec tous mes compliments si tu arrives à t’y retrouver .

Voilà à présent la réponse à # modprobe rt2870sta :

WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.

Là ç’est plus court mais ça ne rigole pas , c’est grave ?

#6

J’ai créé un fichier /etc/modprobe.d/rt2870sta dans lequel j’ai écrit :

blacklist rt2870sta

Voilà où j’en suis .

#7

Ne faut-il pas que j’écrive un truc dans blacklist.conf ?

#8

maintenant , j’ai redémarré et ça me donne ça :

root@cilalos2:/home/kri# modprobe rt2870sta
WARNING: All config files need .conf: /etc/modprobe.d/rt2870sta, it will be ignored in a future release.
WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.

#9

c’est pas bon, il ne faut justement pas blacklister ce module!

à priori il était reconnu au démarrage

annule tes modifs, reboote et essaye

ifup wlan0

et/ou

ifconfig wlan0

parfois ça suffit pour faire apparaitre l’interface wlan0

#10

“Reconnue”, ça ne veut pas dire grand chose. Ici, elle est simplement détectée par le sous-système USB du noyau et identifiée par lsusb, car ses identifiants sont présents dans la base de données que lsusb utilise. Cela ne présume pas de sa prise en charge par un pilote de périphérique présent.

D’après les logs du noyau lors du chargement du module rt2870sta, ce dernier ne semble pas reconnaitre la clé comme un des périphériques qu’il sait gérer. Autrement il y aurait d’autres lignes.

#11

Pour agentsteel ,

J’ai effacé le fichier /etc/modprobe.d/rt2870sta

J’ai rebooté et voilà ce que j’obtiens :

root@cilalos2:/home/kri# modprobe rt2870sta
WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release.
root@cilalos2:/home/kri# ifup wlan0
Ignoring unknown interface wlan0=wlan0.
root@cilalos2:/home/kri# ifconfig wlan0
wlan0: erreur lors de la recherche d’infos sur l’interface: Périphérique non trouvé

Pour PascalHambourg : merci pour ces détails .

#12

J’oubliais : concernant le warning de modprobe, il prévient simplement que dans une future version les fichiers dans /etc/modprobe.d/ devront avoir l’extension .conf sinon ils seront ignorés.

#13

Les difficultés confirment que cette clef ne soit pas placée dans la liste ici : http://wiki.debian.org/rt2870sta .

Mais différentes contributions de forum montrent que certains ont réussi à faire tourner cette clef sous Ubuntu ou Debian comme ici : ubuntuforums.org/showpost.php?p= … ostcount=7

Que faire ?

#14

Il faut essayer un kernel plus récent (le 3.2.x), via les backports.

backports-master.debian.org/Instructions/

ainsi ta clé devrait être supportée via le module rt2800usb

#15

Merci pour tous ces conseils .

Mais j’ai une carte graphique nvidia et donc j’ai un truc comme nvidia-kernel-common .

J’en suis à la version 2.6.32… il faut donc un sacré saut jusqu’à 3.2… Je peux l’installer sans encombres sur une distribution ?

#16

J’ai localisé les paquets linux-image dans synaptic mais je me demande si je vais devoir trouver les paquets nvidia-kernel-common correspondants …

#17

Je ferai volontiers la mise à jour du noyau dès que j’aurai l’assurance de pouvoir conserver un système en bon fonctionnement .

J’hésite un peu à passer en 3.2 vu mon niveau . Car pour l’instant , malgré la quantité faramineuse de logiciels que j’installe ou que je désinstalle , ma Debian tient bon . Bien que j’aimerais tout de même lui faire un petit nettoyage car j’ai Iceweasel qui devient un peu spécial .

Enfin , bref , je voudrais être sûr de ne pas tout casser …

#18

Tu peux faire une image disque de ton système, avec Clonezilla ou Redo backup (si tu as un disque externe ou une autre machine en réseau avec un dossier partagé via samba)

#19

Installer un nouveau noyau ne supprime pas les noyaux déjà installés.

#20

D’après ce que je lis ça le là , Grub pourrait me proposer de démarrer sur l’un ou l’autre des noyaux . Si ça bugue , je redémarre sur le noyau 2.6.32 .